In accordance with the shift lever position, each shift position indicator light will turn on.
Turn the power switch on (ACC).
Check that each shift position indicator light turns on correctly.
| Result | Proceed to |
|---|---|
| All shift position indicator lights turn on simultaneously | A |
| Shift position indicator lights other than corresponding one turn on | B |
| Corresponding shift position indicator light does not turn on | C |
| No shift position indicator lights turn on | D |
Turn the power switch off.
A
B
C
D
Disconnect the K69 and K70 hybrid vehicle control ECU assembly connector.
| *a | Rear view of wire harness connector
(to Hybrid Vehicle Control ECU Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K70-13 (INDP) - Body ground and other terminals | Always | 10 kΩ or higher |
| K69-8 (INDR) - Body ground and other terminals | Always | 10 kΩ or higher |
| K70-12 (INDN) - Body ground and other terminals | Always | 10 kΩ or higher |
| K70-11 (INDD) - Body ground and other terminals | Always | 10 kΩ or higher |
| K70-10 (INDM) - Body ground and other terminals | Always | 10 kΩ or higher |
Reconnect the K69 and K70 hybrid vehicle control ECU assembly connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K69 and K70 hybrid vehicle control ECU assembly connector.
Disconnect the K79 shift position indicator connector.
| *a | Rear view of wire harness connector
(to Hybrid Vehicle Control ECU Assembly) |
| *b | Front view of wire harness connector
(to Shift Position Indicator) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K70-13 (INDP) or K79-4 (P) - Body ground and other terminals | Always | 10 kΩ or higher |
| K69-8 (INDR) or K79-3 (R) - Body ground and other terminals | Always | 10 kΩ or higher |
| K70-12 (INDN) or K79-2 (N) - Body ground and other terminals | Always | 10 kΩ or higher |
| K70-11 (INDD) or K79-1 (D) - Body ground and other terminals | Always | 10 kΩ or higher |
| K70-10 (INDM) or K79-8 (S) - Body ground and other terminals | Always | 10 kΩ or higher |
Reconnect the K79 shift position indicator connector.
Reconnect the K69 and K70 hybrid vehicle control ECU assembly connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K79 shift position indicator connector.
Turn the power switch on (ACC).
| *a | Front view of wire harness connector
(to Shift Position Indicator) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K79-10 (PWR) - Body ground | Power switch on (ACC) | 11 to 14 V |
Turn the power switch off.
Reconnect the K79 shift position indicator connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the power switch on (ACC).
| *a | Component with harness connected
(Hybrid Vehicle Control ECU Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A28-22 (ACCI) - Body ground | Power switch on (ACC) | 11 to 14 V |
Turn the power switch off.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K69 and K70 hybrid vehicle control ECU assembly connector.
Turn the power switch on (ACC).
| *a | Rear view of wire harness connector
(to Hybrid Vehicle Control ECU Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K70-13 (INDP) - Body ground and other terminals | Power switch on (ACC) | 11 to 14 V |
| K69-8 (INDR) - Body ground and other terminals | Power switch on (ACC) | 11 to 14 V |
| K70-12 (INDN) - Body ground and other terminals | Power switch on (ACC) | 11 to 14 V |
| K70-11 (INDD) - Body ground and other terminals | Power switch on (ACC) | 11 to 14 V |
| K70-10 (INDM) - Body ground and other terminals | Power switch on (ACC) | 11 to 14 V |
Turn the power switch off.
Reconnect the K69 and K70 hybrid vehicle control ECU assembly connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K69 and K70 hybrid vehicle control ECU assembly connector.
Disconnect the K79 shift position indicator connector.
| *a | Rear view of wire harness connector
(to Hybrid Vehicle Control ECU Assembly) |
| *b | Front view of wire harness connector
(to Shift Position Indicator) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K70-13 (INDP) - K79-4 (P) | Always | Below 1 Ω |
| K69-8 (INDR) - K79-3 (R) | Always | Below 1 Ω |
| K70-12 (INDN) - K79-2 (N) | Always | Below 1 Ω |
| K70-11 (INDD) - K79-1 (D) | Always | Below 1 Ω |
| K70-10 (INDM) - K79-8 (S) | Always | Below 1 Ω |
Reconnect the K79 shift position indicator connector.
Reconnect the K69 and K70 hybrid vehicle control ECU assembly connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG