Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY) › from 2020.08
RM33C0E _51 Engine / Hybrid System _065433 HYBRID / BATTERY CONTROL _0442440 HYBRID CONTROL SYSTEM(for LITHIUM-ION BATTERY) J

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM(for LITHIUM-ION BATTERY)  ECU Power Source Circuit  


DESCRIPTION

If the power switch is on (IG), the hybrid vehicle control ECU assembly applies current to the MREL terminal to turn the IGCT relay on. This supplies power to the +B1 and +B2 terminals.

WIRING DIAGRAM

A406719E04
1.083,1 1.615,1.26 0.531,0.26 10 false IGCT 0.031,2.667 1.26,3 1.229,0.333 10 false Auxiliary Battery 2.646,1.146 3.563,1.344 0.917,0.198 10 false IGCT 3.896,1.031 4.813,1.229 0.917,0.198 10 false PM-IGCT 0.656,1.469 1.833,1.927 1.177,0.458 10 false Fusible Link Block Assembly 2.229,1.479 3.521,1.979 1.292,0.5 10 false No. 6 Relay Block 0.531,0.833 0.865,1.021 0.333,0.188 10 false A 3.135,0.313 3.469,0.5 0.333,0.188 10 false 1 1.75,0.844 2.146,1.052 0.396,0.208 10 false R117 1.875,0.656 2.208,0.844 0.333,0.188 10 false 1 2.354,0.302 2.688,0.49 0.333,0.188 10 false 2 2.344,0.74 2.677,0.927 0.333,0.188 10 false 3 3.146,0.74 3.479,0.927 0.333,0.188 10 false 5 3.76,0.74 4.094,0.927 0.333,0.188 10 false 1 4.51,0.729 4.844,0.917 0.333,0.188 10 false 2 5.708,0.219 6.042,0.406 0.333,0.188 10 false 6 5.646,0.427 5.979,0.615 0.333,0.188 10 false A29 5.708,0.635 6.042,0.823 0.333,0.188 10 false 4 5.646,0.833 5.979,1.021 0.333,0.188 10 false A29 5.698,1.083 6.031,1.271 0.333,0.188 10 false 1 5.635,1.281 5.969,1.469 0.333,0.188 10 false A28 5.708,2.344 6.042,2.531 0.333,0.188 10 false 5 5.625,2.542 5.958,2.729 0.333,0.188 10 false K69 5.635,2.979 5.969,3.167 0.333,0.188 10 false K70 4.698,3.5 7.135,3.802 2.438,0.302 10 false Hybrid Vehicle Control ECU Assembly 5.969,0.865 6.885,1.063 0.917,0.198 10 false +B1 5.979,1.302 6.896,1.5 0.917,0.198 10 false +B2 5.969,0.427 6.885,0.625 0.917,0.198 10 false MREL 5.969,1.698 6.885,1.896 0.917,0.198 10 false E1 5.979,2.104 6.896,2.302 0.917,0.198 10 false E12 5.969,2.552 6.885,2.75 0.917,0.198 10 false E01 5.969,2.979 6.885,3.177 0.917,0.198 10 false E02 3.646,1.479 4.938,1.979 1.292,0.5 10 false No. 4 Relay Block 5.688,1.49 6.021,1.677 0.333,0.188 10 false 6 5.698,1.917 6.031,2.104 0.333,0.188 10 false 4 5.708,2.771 6.042,2.958 0.333,0.188 10 false 5 5.635,2.125 5.969,2.313 0.333,0.188 10 false K70 5.646,1.698 5.979,1.885 0.333,0.188 10 false K69

CAUTION / NOTICE / HINT

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

1.CHECK HYBRID VEHICLE CONTROL ECU ASSEMBLY (+B1, +B2 VOLTAGE)
a.

Turn the power switch on (IG).


b.
A321140C15
0.677,0.969 1.083,1.167 0.406,0.198 1.229,0.969 1.635,1.167 0.406,0.198 1.938,2.417 1.396,1.708 true 1.229,2.427 1,1.698 true 0.771,0.99 1.229,1.188 0.458,0.198 10 false A28 1.167,2.479 1.625,2.677 0.458,0.198 10 false +B2 0.188,0.333 0.5,0.49 0.313,0.156 10 false *a 1.302,0.99 1.76,1.188 0.458,0.198 10 false A29 1.854,2.469 2.313,2.667 0.458,0.198 10 false +B1
*a Component with harness connected
(Hybrid Vehicle Control ECU Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A29-4 (+B1) - Body ground Power switch on (IG) 11 to 14 V
A28-1 (+B2) - Body ground Power switch on (IG) 11 to 14 V



c.

Turn the power switch off.


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU ASSEMBLY - BODY GROUND)

NG

3.CHECK HYBRID VEHICLE CONTROL ECU ASSEMBLY (MREL VOLTAGE)
2.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU ASSEMBLY - BODY GROUND)
a.

Disconnect the K69 and K70 hybrid vehicle control ECU assembly connectors.


b.
A389532C07
2.417,0.5 2.833,0.75 0.417,0.25 1.833,0.5 2.25,0.75 0.417,0.25 1.198,3.135 1.813,2.354 true 1.625,3.135 1.896,2.375 true 2.313,3.146 2.604,2.365 true 2.979,3.146 2.677,2.365 true 0.177,0.135 0.49,0.292 0.313,0.156 10 false *a 1.104,3.146 1.417,3.302 0.313,0.156 10 false E1 1.521,3.156 1.833,3.313 0.313,0.156 10 false E01 2.167,3.156 2.479,3.313 0.313,0.156 10 false E02 2.906,3.146 3.219,3.302 0.313,0.156 10 false E12 1.948,0.542 2.26,0.74 0.313,0.198 10 false K69 2.531,0.542 2.844,0.74 0.313,0.198 10 false K70
*a Rear view of wire harness connector
(to Hybrid Vehicle Control ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K69-6 (E1) - Body ground Always Below 1 Ω
K69-5 (E01) - Body ground Always Below 1 Ω
K70-5 (E02) - Body ground Always Below 1 Ω
K70-4 (E12) - Body ground Always Below 1 Ω



c.

Reconnect the K69 and K70 hybrid vehicle control ECU assembly connectors.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HYBRID VEHICLE CONTROL ECU ASSEMBLY (MREL VOLTAGE)
a.

Turn the power switch on (IG).


b.
A321140C16
1.229,0.969 1.635,1.167 0.406,0.198 1,2.448 1.25,1.708 true 0.188,0.333 0.5,0.49 0.313,0.156 10 false *a 1.302,0.99 1.76,1.188 0.458,0.198 10 false A29 0.854,2.49 1.313,2.677 0.458,0.188 10 false MREL
*a Component with harness connected
(Hybrid Vehicle Control ECU Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A29-6 (MREL) - Body ground Power switch on (IG) 11 to 14 V



c.

Turn the power switch off.


Result:
Proceed to
OK
NG



OK

4.CHECK FUSE (PM-IGCT)

NG

REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY

4.CHECK FUSE (PM-IGCT)
a.
A406730C02
2.823,1.635 2.271,1.385 true 0.792,0.292 1.104,0.448 0.313,0.156 10 false *1 2.896,1.646 3.208,1.802 0.313,0.156 10 false *2
*1 No. 4 Relay Block
*2 PM-IGCT Fuse


Remove the PM-IGCT fuse from the No. 4 relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
PM-IGCT fuse terminals Always Below 1 Ω



c.

Install the PM-IGCT fuse.


Result:
Proceed to
OK
NG



OK

5.CHECK FUSIBLE LINK BLOCK ASSEMBLY (IGCT FUSE)

NG

12.CHECK HARNESS AND CONNECTOR (NO. 4 RELAY BLOCK - HYBRID VEHICLE CONTROL ECU ASSEMBLY)
5.CHECK FUSIBLE LINK BLOCK ASSEMBLY (IGCT FUSE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the cable from the positive (+) auxiliary battery terminal.


c.
A407368N04
1.75,1.25 2.167,1.479 0.417,0.229 1.76,1.281 2.135,1.458 0.375,0.177 10 true R117

Disconnect the R117 fusible link block assembly connector.


d.
A407369C03
1.208,0.344 1.521,0.552 0.313,0.208 0.344,3.385 0.729,3.667 0.385,0.281 0.479,0.219 0.792,0.375 0.313,0.156 10 false *1 0.583,2.646 0.896,2.802 0.313,0.156 10 false *a 1.333,0.385 1.49,0.583 0.156,0.198 10 false A 0.375,3.438 0.729,3.677 0.354,0.24 10 false R117
*1 Fusible Link Block Assembly
*a Component without harness connected
(Fusible Link Block Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R117-1 - A-1 (Positive (+) auxiliary battery terminal) Power switch off Below 1 Ω



e.

Reconnect the R117 fusible link block assembly connector.


f.

Reconnect the cable to the positive (+) auxiliary battery terminal.


g.

Reconnect the cable to the negative (-) auxiliary battery terminal.


Result:
Proceed to
OK
NG



OK

6.INSPECT RELAY (IGCT)

NG

13.CHECK HARNESS AND CONNECTOR (FUSIBLE LINK BLOCK ASSEMBLY - NO. 6 RELAY BLOCK)
6.INSPECT RELAY (IGCT)
a.
A413714C01
2.396,2.031 2.115,1.396 true 1.146,4.156 1.396,3.604 true 0.177,0.083 0.521,0.365 0.344,0.281 12 false *A 0.188,2.49 0.5,2.802 0.313,0.313 12 false *B 0.229,0.323 0.542,0.479 0.313,0.156 10 false *1 2.385,2.052 2.698,2.208 0.313,0.156 10 false *2 1.042,4.188 1.354,4.344 0.313,0.156 10 false *2 0.229,2.698 0.542,2.854 0.313,0.156 10 false *1
*A for LHD
*B for RHD
*1 No. 6 Relay Block
*2 IGCT Relay


Remove the IGCT relay from the No. 6 relay block.


b.
A253297C01
0.146,0.056 0.409,0.261 0.263,0.205 10 *1
*1 IGCT Relay


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Auxiliary battery voltage not applied between terminals 1 and 2 10 kΩ or higher
Auxiliary battery voltage applied between terminals 1 and 2 Below 1 Ω



c.

Install the IGCT relay.


Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (NO. 4 RELAY BLOCK - HYBRID VEHICLE CONTROL ECU ASSEMBLY)

NG

REPLACE RELAY (IGCT)

7.CHECK HARNESS AND CONNECTOR (NO. 4 RELAY BLOCK - HYBRID VEHICLE CONTROL ECU ASSEMBLY)
a.

Disconnect the A28 and A29 hybrid vehicle control ECU assembly connectors.


b.

Remove the PM-IGCT fuse from the No. 4 relay block.


c.

Measure the resistance according to the value(s) in the table below.

A406731C02
4.094,0.646 4.5,0.938 0.406,0.292 4.729,0.646 5.135,0.938 0.406,0.292 4.083,3.115 4.521,2.365 true 4.688,3.125 4.99,2.375 true 0.615,0.469 0.927,0.625 0.313,0.156 10 false *1 2.458,1.875 2.771,2.031 0.313,0.156 10 false *2 3.479,0.531 3.792,0.688 0.313,0.156 10 false *a 3.865,3.167 4.25,3.427 0.385,0.26 10 false +B2 4.531,3.167 4.917,3.427 0.385,0.26 10 false +B1 4.167,0.708 4.552,0.969 0.385,0.26 10 false A28 4.802,0.708 5.188,0.969 0.385,0.26 10 false A29
*1 No. 4 Relay Block *2 PM-IGCT Fuse
*a Rear view of wire harness connector
(to Hybrid Vehicle Control ECU Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
A29-4 (+B1) - 2 (PM-IGCT fuse) Always Below 1 Ω
A28-1 (+B2) - 2 (PM-IGCT fuse) Always Below 1 Ω



d.

Reconnect the A28 and A29 hybrid vehicle control ECU assembly connectors.


e.

Install the PM-IGCT fuse.


Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (NO. 6 RELAY BLOCK - NO. 4 RELAY BLOCK)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (NO. 6 RELAY BLOCK - NO. 4 RELAY BLOCK)
a.

Remove the IGCT relay from the No. 6 relay block.


b.

Remove the PM-IGCT fuse from the No. 4 relay block.


c.

Measure the resistance according to the value(s) in the table below.

A409123C01
1.813,3.417 1.646,3 true 2.167,1.75 2,1.333 true 0.385,0.177 0.698,0.333 0.313,0.156 12 false *A 0.385,2.01 0.719,2.24 0.333,0.229 12 false *B 0.396,0.365 0.708,0.521 0.313,0.156 10 false *1 3.771,0.375 4.083,0.531 0.313,0.156 10 false *2 2.125,1.792 2.438,1.948 0.313,0.156 10 false *3 5.698,1.865 6.01,2.021 0.313,0.156 10 false *4 1.854,3.427 2.167,3.583 0.313,0.156 10 false *3 0.396,2.219 0.708,2.375 0.313,0.156 10 false *1
*A for LHD *B for RHD
*1 No. 6 Relay Block *2 No. 4 Relay Block
*3 IGCT Relay *4 PM-IGCT Fuse


Standard Resistance:
Tester Connection Condition Specified Condition
5 (IGCT relay) - 1 (PM-IGCT fuse) Always Below 1 Ω



d.

Install the PM-IGCT fuse.


e.

Install the IGCT relay.


Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (FUSIBLE LINK BLOCK ASSEMBLY - NO. 6 RELAY BLOCK)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (FUSIBLE LINK BLOCK ASSEMBLY - NO. 6 RELAY BLOCK)
a.

Disconnect the R117 fusible link block assembly connector.


b.

Remove the IGCT relay from the No. 6 relay block.

A409124C01
6.01,0.427 6.427,0.74 0.417,0.313 4.281,2.021 4.042,1.573 true 2.135,2.073 1.74,1.583 true 0.052,0.396 0.375,0.615 0.323,0.219 12 false *A 3.021,0.396 3.333,0.583 0.313,0.188 12 false *B 0.073,0.646 0.385,0.802 0.313,0.156 10 false *1 4.24,2.031 4.552,2.188 0.313,0.156 10 false *2 5.563,0.938 5.875,1.094 0.313,0.156 10 false *a 2.115,2.104 2.427,2.26 0.313,0.156 10 false *2 6.052,0.51 6.427,0.688 0.375,0.177 10 false R117 3.052,0.635 3.365,0.792 0.313,0.156 10 false *1
*A for LHD *B for RHD
*1 No. 6 Relay Block *2 IGCT Relay
*a Front view of wire harness connector
(to Fusible Link Block Assembly)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (IGCT relay) - R117-1 Always Below 1 Ω



d.

Install the IGCT relay.


e.

Reconnect the R117 fusible link block assembly connector.


Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU ASSEMBLY - NO. 6 RELAY BLOCK)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU ASSEMBLY - NO. 6 RELAY BLOCK)
a.

Disconnect the A29 hybrid vehicle control ECU assembly connector.


b.

Remove the IGCT relay from the No. 6 relay block.


c.

Measure the resistance according to the value(s) in the table below.

A409125C01
4.677,0.719 5.094,1 0.417,0.281 2.146,1.677 1.969,1.354 true 1.823,3.354 1.646,3.031 true 4.552,3 4.792,2.313 true 0.375,0.115 0.708,0.302 0.333,0.188 12 false *A 0.438,2.188 0.781,2.385 0.344,0.198 12 false *B 0.438,2.396 0.75,2.552 0.313,0.156 10 false *1 2.094,1.719 2.406,1.875 0.313,0.156 10 false *2 3.5,1.01 3.813,1.167 0.313,0.156 10 false *a 0.385,0.323 0.542,0.479 0.156,0.156 10 false *1 1.865,3.396 2.177,3.552 0.313,0.156 10 false *2 4.771,0.781 5.125,0.99 0.354,0.208 10 false A29 4.208,3.083 4.802,3.313 0.594,0.229 10 false MREL
*A for LHD *B for RHD
*1 No. 6 Relay Block *2 IGCT Relay
*a Rear view of wire harness connector
(to Hybrid Vehicle Control ECU Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
A29-6 (MREL) - 1 (IGCT relay) Always Below 1 Ω
A29-6 (MREL) or 1 (IGCT relay) - Body ground and other terminals Always 10 kΩ or higher



d.

Install the IGCT relay.


e.

Reconnect the A29 hybrid vehicle control ECU assembly connector.


Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (NO. 6 RELAY BLOCK - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (NO. 6 RELAY BLOCK - BODY GROUND)
a.

Remove the IGCT relay from the No. 6 relay block.


b.
A409126C01
2.26,2.083 2.052,1.594 true 1.844,4.115 1.635,3.625 true 0.229,0.167 0.552,0.396 0.323,0.229 12 false *A 0.333,2.365 0.688,2.646 0.354,0.281 12 false *B 0.25,0.344 0.563,0.5 0.313,0.156 10 false *1 2.198,2.094 2.51,2.25 0.313,0.156 10 false *2 1.781,4.177 2.094,4.333 0.313,0.156 10 false *2 0.354,2.573 0.667,2.729 0.313,0.156 10 false *1
*A for LHD
*B for RHD
*1 No. 6 Relay Block
*2 IGCT Relay


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (IGCT relay) - Body ground Always Below 1 Ω



c.

Install the IGCT relay.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (NO. 4 RELAY BLOCK - HYBRID VEHICLE CONTROL ECU ASSEMBLY)
a.

Remove the PM-IGCT fuse from the No. 4 relay block.


b.

Disconnect the A28 and A29 hybrid vehicle control ECU assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

A406731C02
4.094,0.646 4.5,0.938 0.406,0.292 4.729,0.646 5.135,0.938 0.406,0.292 4.083,3.115 4.521,2.365 true 4.688,3.125 4.99,2.375 true 0.615,0.469 0.927,0.625 0.313,0.156 10 false *1 2.458,1.875 2.771,2.031 0.313,0.156 10 false *2 3.479,0.531 3.792,0.688 0.313,0.156 10 false *a 3.865,3.167 4.25,3.427 0.385,0.26 10 false +B2 4.531,3.167 4.917,3.427 0.385,0.26 10 false +B1 4.167,0.708 4.552,0.969 0.385,0.26 10 false A28 4.802,0.708 5.188,0.969 0.385,0.26 10 false A29
*1 No. 4 Relay Block *2 PM-IGCT Fuse
*a Rear view of wire harness connector
(to Hybrid Vehicle Control ECU Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
A29-4 (+B1) or 2 (PM-IGCT fuse) - Body ground and other terminals Always 10 kΩ or higher
A28-1 (+B2) or 2 (PM-IGCT fuse) - Body ground and other terminals Always 10 kΩ or higher



d.

Reconnect the A28 and A29 hybrid vehicle control ECU assembly connectors.


e.

Install the PM-IGCT fuse.


Result:
Proceed to
OK
NG



OK

REPLACE FUSE (PM-IGCT)

NG

15.REPAIR OR REPLACE HARNESS OR CONNECTOR
13.CHECK HARNESS AND CONNECTOR (FUSIBLE LINK BLOCK ASSEMBLY - NO. 6 RELAY BLOCK)
a.

Disconnect the R117 fusible link block assembly connector.


b.

Remove the IGCT relay from the No. 6 relay block.


c.

Measure the resistance according to the value(s) in the table below.

A409124C01
6.01,0.427 6.427,0.74 0.417,0.313 4.281,2.021 4.042,1.573 true 2.135,2.073 1.74,1.583 true 0.052,0.396 0.375,0.615 0.323,0.219 12 false *A 3.021,0.396 3.333,0.583 0.313,0.188 12 false *B 0.073,0.646 0.385,0.802 0.313,0.156 10 false *1 4.24,2.031 4.552,2.188 0.313,0.156 10 false *2 5.563,0.938 5.875,1.094 0.313,0.156 10 false *a 2.115,2.104 2.427,2.26 0.313,0.156 10 false *2 6.052,0.51 6.427,0.688 0.375,0.177 10 false R117 3.052,0.635 3.365,0.792 0.313,0.156 10 false *1
*A for LHD *B for RHD
*1 No. 6 Relay Block *2 IGCT Relay
*a Front view of wire harness connector
(to Fusible Link Block Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
3 (IGCT relay) or R117-1 - Body ground and other terminals Always 10 kΩ or higher


d.

Install the IGCT relay.


e.

Reconnect the R117 fusible link block assembly connector.


Result:
Proceed to
OK
NG



OK

14.CHECK HARNESS AND CONNECTOR (NO. 6 RELAY BLOCK - NO. 4 RELAY BLOCK)

NG

16.REPAIR OR REPLACE HARNESS OR CONNECTOR
14.CHECK HARNESS AND CONNECTOR (NO. 6 RELAY BLOCK - NO. 4 RELAY BLOCK)
a.

Remove the IGCT relay from the No. 6 relay block.


b.

Remove the PM-IGCT fuse from the No. 4 relay block.


c.

Measure the resistance according to the value(s) in the table below.

A409123C01
1.813,3.417 1.646,3 true 2.167,1.75 2,1.333 true 0.385,0.177 0.698,0.333 0.313,0.156 12 false *A 0.385,2.01 0.719,2.24 0.333,0.229 12 false *B 0.396,0.365 0.708,0.521 0.313,0.156 10 false *1 3.771,0.375 4.083,0.531 0.313,0.156 10 false *2 2.125,1.792 2.438,1.948 0.313,0.156 10 false *3 5.698,1.865 6.01,2.021 0.313,0.156 10 false *4 1.854,3.427 2.167,3.583 0.313,0.156 10 false *3 0.396,2.219 0.708,2.375 0.313,0.156 10 false *1
*A for LHD *B for RHD
*1 No. 6 Relay Block *2 No. 4 Relay Block
*3 IGCT Relay *4 PM-IGCT Fuse


Standard Resistance:
Tester Connection Condition Specified Condition
5 (IGCT relay) or 1 (PM-IGCT fuse) - Body ground and other terminals Always 10 kΩ or higher



d.

Install the PM-IGCT fuse.


e.

Install the IGCT relay.


Result:
Proceed to
OK
NG



OK

REPLACE FUSIBLE LINK BLOCK ASSEMBLY (IGCT FUSE)

NG

17.REPAIR OR REPLACE HARNESS OR CONNECTOR
15.REPAIR OR REPLACE HARNESS OR CONNECTOR
Result:
Proceed to
NEXT



NEXT

REPLACE FUSE (PM-IGCT)

16.REPAIR OR REPLACE HARNESS OR CONNECTOR
Result:
Proceed to
NEXT



NEXT

REPLACE FUSIBLE LINK BLOCK ASSEMBLY (IGCT FUSE)

17.REPAIR OR REPLACE HARNESS OR CONNECTOR
Result:
Proceed to
NEXT



NEXT

REPLACE FUSIBLE LINK BLOCK ASSEMBLY (IGCT FUSE)