Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM (w/ Automatic Headlight Beam Level Control System) › from 2020.08
RM33C0E _59 Vehicle Exterior _065472 LIGHTING (EXT) _0331112 LIGHTING SYSTEM(w/ Automatic Headlight Beam Level Control System) J

LIGHTING (EXT)  LIGHTING SYSTEM(w/ Automatic Headlight Beam Level Control System)  Back-up Light Circuit  


DESCRIPTION

The hybrid vehicle control ECU assembly controls the back-up lights via the BKUP LP relay.

WIRING DIAGRAM

E371563E03
0.99,1.719 2.417,2.208 1.427,0.49 10 false Hybrid Vehicle Control ECU Assembly 1.917,1.083 2.146,1.313 0.229,0.229 10 false BL 2.167,0.979 2.396,1.208 0.229,0.229 10 false 2 0.938,3.323 1.281,3.552 0.344,0.229 10 false W15 3.667,1.083 3.896,1.313 0.229,0.229 10 false 3C 3.656,0.906 3.885,1.135 0.229,0.229 10 false 19 4.563,1.354 5.26,1.615 0.698,0.26 10 false BKUP LP 4.583,0.458 5.281,0.719 0.698,0.26 10 false BKUP LP 5.677,0.313 7.052,0.677 1.375,0.365 10 false from IG1-NO. 1 Relay 3.656,2.219 3.885,2.448 0.229,0.229 10 false 3B 3.698,2.042 3.927,2.271 0.229,0.229 10 false 3 3.656,2.698 3.885,2.927 0.229,0.229 10 false 3D 3.656,2.531 3.885,2.76 0.229,0.229 10 false 10 4.219,4.427 7.063,4.698 2.844,0.271 10 false Instrument Panel Junction Block Assembly 0.938,3.458 2.656,3.792 1.719,0.333 10 false Rear Light Assembly LH 0.938,4.75 2.823,5.115 1.885,0.365 10 false Rear Light Assembly LH 0.938,6.031 2.635,6.385 1.698,0.354 10 false Rear Light Assembly RH 0.927,7.323 2.583,7.677 1.656,0.354 10 false Rear Light Assembly RH 2.135,2.583 2.365,2.813 0.229,0.229 10 false B 2.125,3.885 2.354,4.115 0.229,0.229 10 false B 2.135,5.177 2.365,5.406 0.229,0.229 10 false B 2.125,6.469 2.354,6.698 0.229,0.229 10 false B 0.979,2.594 1.208,2.823 0.229,0.229 10 false E 0.958,3.896 1.188,4.125 0.229,0.229 10 false E 0.969,5.177 1.198,5.406 0.229,0.229 10 false E 0.969,6.479 1.198,6.708 0.229,0.229 10 false E 1.208,2.885 2.49,3.25 1.281,0.365 10 false Back-up Light 1.188,4.198 2.469,4.563 1.281,0.365 10 false Back-up Light 1.198,5.469 2.479,5.833 1.281,0.365 10 false Back-up Light 1.208,6.771 2.49,7.135 1.281,0.365 10 false Back-up Light 0.979,1.583 1.406,1.802 0.427,0.219 10 false A29 0.927,4.615 1.271,4.844 0.344,0.229 10 false W17 0.927,5.896 1.271,6.125 0.344,0.229 10 false W14 0.927,7.177 1.271,7.406 0.344,0.229 10 false W16 2.344,2.583 2.573,2.813 0.229,0.229 10 false 2 2.333,3.875 2.563,4.104 0.229,0.229 10 false 2 2.333,5.167 2.563,5.396 0.229,0.229 10 false 2 2.333,6.458 2.563,6.688 0.229,0.229 10 false 2 0.792,2.604 1.021,2.833 0.229,0.229 10 false 4 0.792,3.896 1.021,4.125 0.229,0.229 10 false 1 0.792,5.177 1.021,5.406 0.229,0.229 10 false 4 0.802,6.469 1.031,6.698 0.229,0.229 10 false 1 4.354,6.635 6.417,7.01 2.063,0.375 10 false *2: for Bulb Type Back-up Light 4.354,6.302 6.51,6.688 2.156,0.385 10 false *1: for LED Type Back-up Light 2.677,2.604 2.906,2.833 0.229,0.229 10 false *1 2.698,5.177 2.927,5.406 0.229,0.229 10 false *1 2.688,3.896 2.917,4.125 0.229,0.229 10 false *2 2.698,6.458 2.927,6.688 0.229,0.229 10 false *2

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the hybrid vehicle control ECU assembly, refer to Service Bulletin.



PROCEDURE

1.CHECK FOR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


e.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397

Result:
Result Proceed to
Hybrid control system DTCs are not output A
Hybrid control system DTCs are output B



A

2.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BODY GROUND)

B

2.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BODY GROUND)
a.

Disconnect the 3B instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3B-3 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 3C instrument panel junction block assembly connector.


b.

Disconnect the A29 hybrid vehicle control ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A29-2 (BL) - 3C-19 Always Below 1 Ω
A29-2 (BL) or 3C-19 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HYBRID VEHICLE CONTROL ECU ASSEMBLY (OUTPUT VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HYBRID VEHICLE CONTROL ECU ASSEMBLY (OUTPUT VOLTAGE)
E356599C05
0.938,1.677 1.208,1.938 0.271,0.26 0.99,1.729 1.302,1.927 0.313,0.198 10 false 3C 0.458,0.208 0.771,0.406 0.313,0.198 10 false *a
*a Component with harness connected
(Instrument Panel Junction Block Assembly)


a.

Connect the A29 hybrid vehicle control ECU assembly connector.


b.

Connect the 3B and 3C instrument panel junction block assembly connectors.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3C-19 - Body ground Power switch off, shift lever not in R Below 1 V
3C-19 - Body ground Power switch on (IG), shift lever in R 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (OUTPUT VOLTAGE)

NG

REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY

5.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (OUTPUT VOLTAGE)
E356599C06
0.875,0.74 1.146,1 0.271,0.26 0.927,0.792 1.24,0.99 0.313,0.198 10 false 3D 0.458,0.208 0.771,0.406 0.313,0.198 10 false *a
*a Component with harness connected
(Instrument Panel Junction Block Assembly)


a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3D-10 - Body ground Power switch off, shift lever not in R Below 1 V
3D-10 - Body ground Power switch on (IG), shift lever in R 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY