53156G
1.INSTALL NO. 2 RADIATOR GRILLE SEAL
When installing the No. 2 radiator grille seal, heat the radiator shutter using a heat light.
| Item | Temperature |
|---|---|
| Radiator Shutter | 20 to 30°C (68 to 86°F) |
| *a | Heated Part |
| *b | Heat Light |
Do not touch the heat light and heated parts, touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
Do not heat the radiator shutter excessively.
Clean the radiator shutter surface.
Using a heat light, heat the radiator shutter surface.
Remove any remaining double-sided tape from the radiator shutter.
Wipe off any tape adhesive residue with cleaner.
Remove the release paper from a new No. 2 radiator grille seal.
After removing the release paper, keep the exposed adhesive free from foreign matter.
Install the No. 2 radiator grille seal.
If the No. 2 radiator grille seal has been removed, it must be replaced with a new one as it may be deformed or the strength of its adhesive may be deteriorated.
Press the No. 2 radiator grille seal firmly to install it.
53155J
2.INSTALL NO. 1 RADIATOR GRILLE SEAL
When installing the No. 1 radiator grille seal, heat the radiator shutter using a heat light.
| Item | Temperature |
|---|---|
| Radiator Shutter | 20 to 30°C (68 to 86°F) |
| *a | Heated Part |
| *b | Heat Light |
Do not touch the heat light and heated parts, touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
Do not heat the radiator shutter excessively.
Clean the radiator shutter surface.
Using a heat light, heat the radiator shutter surface.
Remove any remaining double-sided tape from the radiator shutter.
Wipe off any tape adhesive residue with cleaner.
Using a heat light, heat the radiator shutter.
Remove the release paper from a new No. 1 radiator grille seal.
After removing the release paper, keep the exposed adhesive free from foreign matter.
Install the No. 1 radiator grille seal.
If the No. 1 radiator grille seal has been removed, it must be replaced with a new one as it may be deformed or the strength of its adhesive may be deteriorated.
Press the No. 1 radiator grille seal firmly to install it.
53157C
3.INSTALL NO. 3 RADIATOR GRILLE SEAL
When installing the No. 3 radiator grille seal, heat the radiator shutter using a heat light.
Use the same procedure for the RH side and LH side.
| Item | Temperature |
|---|---|
| Radiator Shutter | 20 to 30°C (68 to 86°F) |
| *a | Heated Part |
| *b | Heat Light |
Do not touch the heat light and heated parts, touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
Do not heat the radiator shutter excessively.
Clean the radiator shutter surface.
Using a heat light, heat the radiator shutter surface.
Remove any remaining double-sided tape from the radiator shutter.
Wipe off any tape adhesive residue with cleaner.
Remove the release paper from a new No. 3 radiator grille seal.
After removing the release paper, keep the exposed adhesive free from foreign matter.
Install the No. 3 radiator grille seal.
If the No. 3 radiator grille seal has been removed, it must be replaced with a new one as it may be deformed or the strength of its adhesive may be deteriorated.
Press the No. 3 radiator grille seal firmly to install it.
82090A
4.INSTALL EXTENSION WIRE ASSEMBLY
Connect the connector.
Engage the 2 clamps to install the extension wire assembly.