Refer to DTC P036511.
Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>P036511
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P03652A | Camshaft Position Sensor "B" Bank 1 Signal Stuck in Range | No camshaft position sensor (for exhaust camshaft) signal to ECM while engine cranking (1 trip detection logic). | ·
Open or short in camshaft position sensor (for exhaust camshaft) circuit ·
Camshaft position sensor (for exhaust camshaft) ·
Exhaust camshaft ·
ECM |
Comes on | DTC stored | SAE Code: P0365 |
| P036531 | Camshaft Position Sensor "B" Bank 1 No Signal | No camshaft position sensor (for exhaust camshaft) signal for 5 seconds at an engine speed of 600 rpm or higher (1 trip detection logic). | ·
Open or short in camshaft position sensor (for exhaust camshaft) circuit ·
Camshaft position sensor (for exhaust camshaft) ·
Exhaust camshaft ·
ECM |
Comes on | DTC stored | SAE Code: P0365 |
Reference: Inspection using an oscilloscope.
Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>P034011
If no pulse signal is transmitted by the camshaft position sensor (for exhaust camshaft) despite the camshaft rotating, or the rotation of the camshaft and the crankshaft is not synchronized, the ECM interprets this as a malfunction of the sensor.
| Required Sensors/Components (Main) | Camshaft position sensor (for exhaust camshaft) |
| Required Sensors/Components (Related) | Crankshaft position sensor |
| Frequency of Operation | Continuous |
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the power switch off and wait for at least 30 seconds.
Turn the power switch on (IG).
Turn the GTS on.
Put the engine in Inspection Mode (Maintenance Mode).
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE
Start the engine [A].
Idle the engine for 10 seconds or more [B].
Enter the following menus: Powertrain / Engine / Trouble Codes [C].
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P03652A or P036531.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
If the judgment result is NORMAL, the system is normal.
If the judgment result is ABNORMAL, the system is malfunctioning.
If the judgment result is INCOMPLETE, perform steps [B] through [C] again.
Refer to DTC P036511.
Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>P036511
Vehicle Control History may be stored in the hybrid vehicle control ECU assembly if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the freeze frame data and Vehicle Control History can be useful for troubleshooting.
- for Nickel Metal Hydride: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>VEHICLE CONTROL HISTORY
- for Lithium-ion Battery: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY)>VEHICLE CONTROL HISTORY
(Select Powertrain in Health Check and then check the time stamp data.)
If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU assembly, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.
- for Nickel Metal Hydride: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>VEHICLE CONTROL HISTORY
- for Lithium-ion Battery: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY)>VEHICLE CONTROL HISTORY
If no problem is found through this diagnostic troubleshooting procedure, there may be a mechanical problem with the engine.
Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
| *a | Front view of wire harness connector
(to Camshaft Position Sensor (for Exhaust Camshaft)) |
Make sure that the connector is properly connected. If it is not, securely connect it and check for DTCs again.
Disconnect the camshaft position sensor (for exhaust camshaft) connector.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C77-3 (VC2) - Body ground | Power switch on (IG) | 4.5 to 5.5 V |
| C77-1 (VVE+) - Body ground | Power switch on (IG) | 3.0 to 5.0 V |
Turn the power switch off and wait for at least 30 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C77-3 (VC2) - C77-1 (VVE+) | Power switch off | 1.425 to 1.575 kΩ |
| C77-2 (VVE-) - Body ground | Power switch off | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Clearance |
Visually check the camshaft position sensor (for exhaust camshaft) for damage.
Check the camshaft position sensor (for exhaust camshaft) installation condition.
The camshaft position sensor (for exhaust camshaft) does not have any damage and is installed properly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the timing rotor of the exhaust camshaft.
Camshaft timing rotor does not have any cracks or deformation.
Perform "Inspection After Repair" after replacing the exhaust camshaft.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the camshaft position sensor (for exhaust camshaft) connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C77-1 (VVE+) - C100-91 (EV1+) | Always | Below 1 Ω |
| C77-2 (VVE-) - C100-114 (EV1-) | Always | Below 1 Ω |
| C77-3 (VC2) - C100-113 (VCE1) | Always | Below 1 Ω |
| C77-1 (VVE+) or C100-91 (EV1+) - Body ground and other terminals | Always | 10 kΩ or higher |
| C77-2 (VVE-) or C100-114 (EV1-) - Body ground and other terminals | Always | 10 kΩ or higher |
| C77-3 (VC2) or C100-113 (VCE1) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG