Home › Engine / Hybrid System › A25A-FXS (ENGINE CONTROL) › SFI SYSTEM (w/o Canister Pump Module) › from 2020.08
RM33C0E _51 Engine / Hybrid System _065419 A25A-FXS ENGINE CONTROL _0331447 SFI SYSTEM(w/o Canister Pump Module) C

A25A-FXS ENGINE CONTROL  SFI SYSTEM(w/o Canister Pump Module)  P123513  High Pressure Fuel Pump Circuit Open  


DESCRIPTION

The high-pressure direct injection fuel system consists of a spill control valve, check valve, fuel relief valve, fuel pressure sensor (for high pressure side), fuel pump assembly (for high pressure side) and direct fuel injector assemblies. The spill control valve adjusts the return volume of the high-pressure fuel. The check valve mechanically opens and closes the paths to the fuel delivery pipes. The relief valve releases the fuel back to the fuel tank if the high-pressure fuel system malfunctions. The fuel pump assembly (for high pressure side) is installed to the cylinder head cover and operated by a cam installed to the end of the exhaust camshaft. Rotation of the camshaft moves the pump plunger inside the fuel pump assembly (for high pressure side) up and down, pressurizing the fuel. The pressurized fuel opens the check valve and is pumped into the fuel delivery pipe.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P123513 High Pressure Fuel Pump Circuit Open Open or short in fuel pump assembly (for high pressure side) circuit detected 60 times or more (1 trip detection logic).
·

Open or short in fuel pump assembly (for high pressure side) circuit

·

Fuel pump assembly (for high pressure side)

·

ECM


Comes on DTC stored SAE Code: P1235

MONITOR DESCRIPTION

If an open or short in the fuel pump assembly (for high pressure side) circuit is detected after the engine is started, the ECM will illuminate the MIL and store this DTC.

MONITOR STRATEGY

Required Sensors/Components (Main) Fuel pump assembly (for high pressure side)
Required Sensors/Components (Related) Injector driver (ECM)
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG).

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the power switch off and wait for at least 30 seconds.

6.

Turn the power switch on (IG).

7.

Turn the GTS on.

8.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

9.

Start the engine [A].

10.

Idle the engine for 10 seconds [B].

11.

Enter the following menus: Powertrain / Engine / Trouble Codes [C].

12.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



13.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

14.

Input the DTC: P123513.

15.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system has a malfunction.

·

If the judgment result is INCOMPLETE, perform steps [B] through [C] again.




WIRING DIAGRAM

A404929E03
0.51,2.01 0.854,2.302 0.344,0.292 10 false C31 0.521,2.198 3.594,2.51 3.073,0.313 10 false Fuel Pump Assembly (for High Pressure Side) 1.813,0.646 1.99,0.896 0.177,0.25 10 false 1 1.427,0.656 1.865,0.927 0.438,0.271 10 false FP+ 1.823,1.344 1.979,1.542 0.156,0.198 10 false 2 1.448,1.354 1.906,1.552 0.458,0.198 10 false FP- 5,0.667 5.313,0.865 0.313,0.198 10 false 19 5.271,0.813 5.865,1.083 0.594,0.271 10 false FP1+ 5.01,1.344 5.323,1.542 0.313,0.198 10 false 18 5.271,1.458 5.844,1.708 0.573,0.25 10 false FP1- 5.375,2.042 5.719,2.333 0.344,0.292 10 false C100 5.823,2.042 6.333,2.365 0.51,0.323 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:
·

Vehicle Control History may be stored in the hybrid vehicle control ECU assembly if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the freeze frame data and Vehicle Control History can be useful for troubleshooting.

- for Nickel Metal Hydride: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>VEHICLE CONTROL HISTORY

- for Lithium-ion Battery: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY)>VEHICLE CONTROL HISTORY

(Select Powertrain in Health Check and then check the time stamp data.)

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>DTC CHECK / CLEAR

·

If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU assembly, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.

- for Nickel Metal Hydride: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>VEHICLE CONTROL HISTORY

- for Lithium-ion Battery: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY)>VEHICLE CONTROL HISTORY



HINT:
·

If the current from the D INJ relay is cut because DTC P062D13 is stored, DTC P123513 will be stored even if the fuel pump assembly (for high pressure side) is normal.

·

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.INSPECT FUEL(ENGINE ROOM SIDE) PUMP ASSEMBLY (FOR HIGH PRESSURE SIDE)
a.

Inspect the fuel pump assembly (for high pressure side).

Click hereEngine / Hybrid System>A25A-FXS (FUEL)>FUEL PUMP (for High Pressure)>INSPECTION


HINT:

Perform "Inspection After Repair" after replacing the fuel pump assembly (for high pressure side).

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>INITIALIZATION


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (FUEL PUMP ASSEMBLY (FOR HIGH PRESSURE SIDE) - ECM)

NG

REPLACE FUEL(ENGINE ROOM SIDE) PUMP ASSEMBLY (FOR HIGH PRESSURE SIDE)

2.CHECK HARNESS AND CONNECTOR (FUEL PUMP ASSEMBLY (FOR HIGH PRESSURE SIDE) - ECM)
a.

Disconnect the fuel pump assembly (for high pressure side) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C31-1 (FP+) - C100-19 (FP1+) Always Below 1 Ω
C31-2 (FP-) - C100-18 (FP1-) Always Below 1 Ω
C31-1 (FP+) or C100-19 (FP1+) - Body ground and other terminals Always 10 kΩ or higher
C31-2 (FP-) or C100-18 (FP1-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR