1.INSPECT SPIRAL CABLE SUB-ASSEMBLY (w/o Occupant Classification System)
Do not remove the steering sensor from the spiral cable sub-assembly when inspecting the spiral cable sub-assembly.
Remove the steering sensor from the spiral cable sub-assembly only when replacing the spiral cable sub-assembly.
Visually check the spiral cable sub-assembly for defects.
The defects are as follows:
Scratches
Small cracks
Dents
Chips
Cracks or other damage to the connector
No defects are found.
If any of the defects is found, replace the spiral cable sub-assembly with a new one.
Check the spiral cable sub-assembly.
| *A | w/o Heated Steering Wheel System | *B | w/ Heated Steering Wheel System |
| *a | Component without harness connected
(Spiral Cable Sub-assembly) |
- | - |
|
Interlock | - | - |
When rotating the spiral cable sub-assembly, make sure to push on the interlock shown in the illustration to release the interlock mechanism.
As the spiral cable sub-assembly may break, do not rotate the spiral cable sub-assembly more than the specified amount.
Set the spiral cable sub-assembly to the center position.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSTALLATION
Measure the resistance between each terminal of the spiral cable sub-assembly according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
*: w/ Heated Steering Wheel System |
||
| K22-1 (SDN) - z4-4 (SDN) | Always | 3 Ω or less |
| K22-2 (ECC) - z4-3 (ECC) | Always | 3 Ω or less |
| K22-2 (ECC) - z1-12 (ECC) | Always | 3 Ω or less |
| K22-4 (EAU) - z1-10 (EAU) | Always | 3 Ω or less |
| K22-5 (AU2) - z1-9 (AU2) | Always | 3 Ω or less |
| K22-6 (DIST) - z1-8 (DIST) | Always | 3 Ω or less |
| K22-7 (HO) - A (HO) | Always | 3 Ω or less |
| K22-8 (SUP) - z4-2 (SUP) | Always | 3 Ω or less |
| K22-9 (IL-2) - z1-6 (IL-2) | Always | 3 Ω or less |
| K22-10 (+DP2) - z1-5 (+DP2) | Always | 3 Ω or less |
| K22-11 (+DP) - z1-4 (+DP) | Always | 3 Ω or less |
| K22-12 (AU1) - z1-3 (AU1) | Always | 3 Ω or less |
| K22-13 (CCS) - z1-2 (CCS) | Always | 3 Ω or less |
| K22-14 (IL+2) - z1-1 (IL+2) | Always | 3 Ω or less |
| K24-1 (D+) - z9-2 (D+) | Always | Below 1 Ω |
| K24-2 (D-) - z9-1 (D-) | Always | Below 1 Ω |
| K150-2 (EHT) - z29-1 (EHT)* | Always | Below 0.1 Ω |
| K150-4 (BHT) - z29-4 (BHT)* | Always | Below 0.1 Ω |
After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise, and measure the resistance according to the value(s) in the table below. Then rotate the spiral cable sub-assembly 5 times counterclockwise, and measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
*: w/ Heated Steering Wheel System |
||
| K22-1 (SDN) - z4-4 (SDN) | Always | 3 Ω or less |
| K22-2 (ECC) - z4-3 (ECC) | Always | 3 Ω or less |
| K22-2 (ECC) - z1-12 (ECC) | Always | 3 Ω or less |
| K22-4 (EAU) - z1-10 (EAU) | Always | 3 Ω or less |
| K22-5 (AU2) - z1-9 (AU2) | Always | 3 Ω or less |
| K22-6 (DIST) - z1-8 (DIST) | Always | 3 Ω or less |
| K22-7 (HO) - A (HO) | Always | 3 Ω or less |
| K22-8 (SUP) - z4-2 (SUP) | Always | 3 Ω or less |
| K22-9 (IL-2) - z1-6 (IL-2) | Always | 3 Ω or less |
| K22-10 (+DP2) - z1-5 (+DP2) | Always | 3 Ω or less |
| K22-11 (+DP) - z1-4 (+DP) | Always | 3 Ω or less |
| K22-12 (AU1) - z1-3 (AU1) | Always | 3 Ω or less |
| K22-13 (CCS) - z1-2 (CCS) | Always | 3 Ω or less |
| K22-14 (IL+2) - z1-1 (IL+2) | Always | 3 Ω or less |
| K24-1 (D+) - z9-2 (D+) | Always | Below 1 Ω |
| K24-2 (D-) - z9-1 (D-) | Always | Below 1 Ω |
| K150-2 (EHT) - z29-1 (EHT)* | Always | Below 0.1 Ω |
| K150-4 (BHT) - z29-4 (BHT)* | Always | Below 0.1 Ω |
After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise. Then while rotating the spiral cable sub-assembly 5 times counterclockwise, measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
*: w/ Heated Steering Wheel System |
||
| K22-1 (SDN) - z4-4 (SDN) | Always | 3 Ω or less |
| K22-2 (ECC) - z4-3 (ECC) | Always | 3 Ω or less |
| K22-2 (ECC) - z1-12 (ECC) | Always | 3 Ω or less |
| K22-4 (EAU) - z1-10 (EAU) | Always | 3 Ω or less |
| K22-5 (AU2) - z1-9 (AU2) | Always | 3 Ω or less |
| K22-6 (DIST) - z1-8 (DIST) | Always | 3 Ω or less |
| K22-7 (HO) - A (HO) | Always | 3 Ω or less |
| K22-8 (SUP) - z4-2 (SUP) | Always | 3 Ω or less |
| K22-9 (IL-2) - z1-6 (IL-2) | Always | 3 Ω or less |
| K22-10 (+DP2) - z1-5 (+DP2) | Always | 3 Ω or less |
| K22-11 (+DP) - z1-4 (+DP) | Always | 3 Ω or less |
| K22-12 (AU1) - z1-3 (AU1) | Always | 3 Ω or less |
| K22-13 (CCS) - z1-2 (CCS) | Always | 3 Ω or less |
| K22-14 (IL+2) - z1-1 (IL+2) | Always | 3 Ω or less |
| K24-1 (D+) - z9-2 (D+) | Always | Below 1 Ω |
| K24-2 (D-) - z9-1 (D-) | Always | Below 1 Ω |
| K150-2 (EHT) - z29-1 (EHT)* | Always | Below 0.1 Ω |
| K150-4 (BHT) - z29-4 (BHT)* | Always | Below 0.1 Ω |
If the result is not as specified, replace the spiral cable sub-assembly.
2.INSPECT SPIRAL CABLE SUB-ASSEMBLY (w/ Occupant Classification System)
Do not remove the steering sensor from the spiral cable sub-assembly when inspecting the spiral cable sub-assembly.
Remove the steering sensor from the spiral cable sub-assembly only when replacing the spiral cable sub-assembly.
Visually check the spiral cable sub-assembly for defects.
The defects are as follows:
Scratches
Small cracks
Dents
Chips
Cracks or other damage to the connector
No defects are found.
If any of the defects is found, replace the spiral cable sub-assembly with a new one.
Check the spiral cable sub-assembly.
| *a | Component without harness connected
(Spiral Cable Sub-assembly) |
*b | Color: Light Green |
| *c | Color: Black | - | - |
|
Interlock | - | - |
When rotating the spiral cable sub-assembly, make sure to push on the interlock shown in the illustration to release the interlock mechanism.
As the spiral cable sub-assembly may break, do not rotate the spiral cable sub-assembly more than the specified amount.
Set the spiral cable sub-assembly to the center position.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSTALLATION
Measure the resistance between each terminal of the spiral cable sub-assembly according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K22-2 (ECC) - z1-12 (ECC) | Always | 3 Ω or less |
| K22-4 (EAU) - z1-10 (EAU) | Always | 3 Ω or less |
| K22-5 (AU2) - z1-9 (AU2) | Always | 3 Ω or less |
| K22-6 (DIST) - z1-8 (DIST) | Always | 3 Ω or less |
| K22-7 (HO) - A (HO) | Always | 3 Ω or less |
| K22-9 (IL-2) - z1-6 (IL-2) | Always | 3 Ω or less |
| K22-10 (+DP2) - z1-5 (+DP2) | Always | 3 Ω or less |
| K22-11 (+DP) - z1-4 (+DP) | Always | 3 Ω or less |
| K22-12 (AU1) - z1-3 (AU1) | Always | 3 Ω or less |
| K22-13 (CCS) - z1-2 (CCS) | Always | 3 Ω or less |
| K22-14 (IL+2) - z1-1 (IL+2) | Always | 3 Ω or less |
| K24-1 (D+) - z2-2 (D+) | Always | Below 1 Ω |
| K24-2 (D-) - z2-1 (D-) | Always | Below 1 Ω |
| K24-3 (D2-) - z3-1 (D2-) | Always | Below 1 Ω |
| K24-4 (D2+) - z3-2 (D2+) | Always | Below 1 Ω |
After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise, and measure the resistance according to the value(s) in the table below. Then rotate the spiral cable sub-assembly 5 times counterclockwise, and measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K22-2 (ECC) - z1-12 (ECC) | Always | 3 Ω or less |
| K22-4 (EAU) - z1-10 (EAU) | Always | 3 Ω or less |
| K22-5 (AU2) - z1-9 (AU2) | Always | 3 Ω or less |
| K22-6 (DIST) - z1-8 (DIST) | Always | 3 Ω or less |
| K22-7 (HO) - A (HO) | Always | 3 Ω or less |
| K22-9 (IL-2) - z1-6 (IL-2) | Always | 3 Ω or less |
| K22-10 (+DP2) - z1-5 (+DP2) | Always | 3 Ω or less |
| K22-11 (+DP) - z1-4 (+DP) | Always | 3 Ω or less |
| K22-12 (AU1) - z1-3 (AU1) | Always | 3 Ω or less |
| K22-13 (CCS) - z1-2 (CCS) | Always | 3 Ω or less |
| K22-14 (IL+2) - z1-1 (IL+2) | Always | 3 Ω or less |
| K24-1 (D+) - z2-2 (D+) | Always | Below 1 Ω |
| K24-2 (D-) - z2-1 (D-) | Always | Below 1 Ω |
| K24-3 (D2-) - z3-1 (D2-) | Always | Below 1 Ω |
| K24-4 (D2+) - z3-2 (D2+) | Always | Below 1 Ω |
After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise. Then while rotating the spiral cable sub-assembly 5 times counterclockwise, measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K22-2 (ECC) - z1-12 (ECC) | Always | 3 Ω or less |
| K22-4 (EAU) - z1-10 (EAU) | Always | 3 Ω or less |
| K22-5 (AU2) - z1-9 (AU2) | Always | 3 Ω or less |
| K22-6 (DIST) - z1-8 (DIST) | Always | 3 Ω or less |
| K22-7 (HO) - A (HO) | Always | 3 Ω or less |
| K22-9 (IL-2) - z1-6 (IL-2) | Always | 3 Ω or less |
| K22-10 (+DP2) - z1-5 (+DP2) | Always | 3 Ω or less |
| K22-11 (+DP) - z1-4 (+DP) | Always | 3 Ω or less |
| K22-12 (AU1) - z1-3 (AU1) | Always | 3 Ω or less |
| K22-13 (CCS) - z1-2 (CCS) | Always | 3 Ω or less |
| K22-14 (IL+2) - z1-1 (IL+2) | Always | 3 Ω or less |
| K24-1 (D+) - z2-2 (D+) | Always | Below 1 Ω |
| K24-2 (D-) - z2-1 (D-) | Always | Below 1 Ω |
| K24-3 (D2-) - z3-1 (D2-) | Always | Below 1 Ω |
| K24-4 (D2+) - z3-2 (D2+) | Always | Below 1 Ω |
If the result is not as specified, replace the spiral cable sub-assembly.