Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › FRONT DRIVE SHAFT ASSEMBLY › from 2021.02
RM33C0E _52 Drivetrain _065435 DRIVE SHAFT / PROPELLER SHAFT _0328128 FRONT DRIVE SHAFT ASSEMBLY A

DRIVE SHAFT / PROPELLER SHAFT  FRONT DRIVE SHAFT ASSEMBLY  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1.INSTALL FRONT AXLE OUTBOARD JOINT BOOT

a.

Secure the drive shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



b.
C166359C04
1.917,0.885 2.427,0.375 2.427,0.375 2.792,0.375 false 2.823,0.281 3.177,0.49 0.354,0.208 10 *a
*a Protective Tape


Wrap the splines of the front drive outboard joint shaft assembly with protective tape to prevent the boot from being damaged.


c.
C274280C01
1.115,1.719 1.115,1.427 false 1.656,1.74 1.656,1.479 false 2.344,1.74 2.344,1.438 false 2.979,1.75 2.979,1.229 false 1.063,1.781 1.375,1.938 0.313,0.156 10 *1 1.604,1.792 1.917,1.948 0.313,0.156 10 *2 2.281,1.781 2.594,1.938 0.313,0.156 10 *3 2.948,1.792 3.26,1.948 0.313,0.156 10 *4
*1 Front Drive Outboard Joint Shaft Assembly
*2 Front No. 2 Axle Outboard Joint Boot Clamp
*3 Front Axle Outboard Joint Boot
*4 Front Axle Outboard Joint Boot Clamp
V100135

Outboard Joint Side
V100136

Inboard Joint Side


Install new parts to the front drive outboard joint shaft assembly in the following order:

i.

Front No. 2 axle outboard joint boot clamp


ii.

Front axle outboard joint boot


iii.

Front axle outboard joint boot clamp



d.

Pack the joint portion of the front drive outboard joint shaft assembly and front axle outboard joint boot with grease.

Standard Grease Capacity:

171 to 181 g (6.04 to 6.38 oz)



e.

Install the front axle outboard joint boot to the front drive outboard joint shaft assembly groove.

NOTICE:
·

Do not allow grease to adhere to the boot clamp track of the outboard joint boot.

·

Keep the inside of the outboard joint boot free of foreign matter.




Hide 43447F 2.INSTALL FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP

CAUTION:
·

Wear protective gloves when installing the front No. 2 axle outboard joint boot clamp.

·

If protective gloves are not worn, injuries may occur.



a.
C415871C01
2.156,1.5 2.677,1.5 false 0.833,1.24 1.354,1.24 false 1.917,2.031 2.438,2.031 false 2.708,1.438 3.021,1.594 0.313,0.156 10 false *a 0.667,1.177 0.979,1.333 0.313,0.156 10 false *b 1.729,1.948 2.042,2.104 0.313,0.156 10 false *c
*a Fulcrum Point
*b Lever Push Position
*c Band Support Position


Install the front No. 2 axle outboard joint boot clamp to the front axle outboard joint boot and temporarily fold back the lever at the fulcrum point.

NOTICE:
·

Set the lever to the guide groove correctly and install the clamp as far to the inside of the vehicle as possible.

·

Check the band and the lever for any deformation before folding back the lever.

·

The lever folds easily at the fulcrum point when pushed at the position shown in the illustration.

·

When folding back the lever, do not push at the end of the lever.

C415873C01
6.771,1.49 6.125,1.49 true 5.948,1.417 6.26,1.573 0.313,0.156 10 false *a
*a Temporary Claw - -


·

If the lever bends in the middle, it may not engage with the temporary claws or may not be held in the correct position.




b.

As shown in the illustration, while pressing the outboard joint area against the work surface, firmly press the lever into place by rolling the outboard joint area forward from the folded fulcrum point to the temporary claw area until a click sound is heard.

C415872C01
3.604,1.052 3.135,1.406 3.135,1.406 3.708,1.042 true 2.083,1.49 1.594,1.49 true 1.958,2.281 1.688,2.281 1.688,2.281 1.448,1.906 true 5.927,2.229 5.646,1.938 5.646,1.938 5.49,1.938 true 3.823,0.292 4.135,0.448 0.313,0.156 10 false *a 4.104,1.302 4.417,1.458 0.313,0.156 10 false *b 5.24,0.583 5.552,0.74 0.313,0.156 10 false *c 2.979,1.354 3.292,1.51 0.313,0.156 10 false *d 1.208,2.365 1.521,2.521 0.313,0.156 10 false *b 1.427,1.417 1.74,1.573 0.313,0.156 10 false *d 2.01,2.219 2.323,2.375 0.313,0.156 10 false *e 5.281,1.875 5.594,2.031 0.313,0.156 10 false *d
*a Press down *b Contact Point
*c Roll forward *d Temporary Claw
*e Fulcrum Point - -


NOTICE:
·

Do not damage the deflector.

·

Make sure that the outboard joint is in direct contact with the work surface.




c.
C265825C08
1.698,3.75 1.031,4.448 1.031,4.448 1.917,3.802 true 0.865,4.396 1.146,4.583 0.281,0.188 10 false *a
*a Buckle


Using a plastic hammer, bend the buckle to secure the lever and confirm that the tip of the lever is aligned with the buckle as shown in the illustration.

NOTICE:
·

Do not use excessive force when tapping with the plastic hammer.

·

Do not damage the front axle outboard joint boot.




Hide 43447E 3.INSTALL FRONT AXLE OUTBOARD JOINT BOOT CLAMP

CAUTION:
·

Wear protective gloves when installing the front axle outboard joint boot clamp.

·

If protective gloves are not worn, injuries may occur.



a.
C107948

Install the front axle outboard joint boot clamp to the front axle outboard joint boot and partially bend down the lever.

NOTICE:
·

Make sure that the front axle outboard joint boot clamp is correctly positioned within the groove.

·

Confirm that the front axle outboard joint boot clamp and lever are not deformed or damaged.




b.
C158356C01
2.469,0.938 2.771,1.219 0.302,0.281 10 false *a
*a Place the tip near the center of the lever


Using water pump pliers, temporarily secure the front axle outboard joint boot clamp by pinching the front axle outboard joint boot clamp until a click sound is heard.

NOTICE:

Do not damage the front axle outboard joint boot.



c.
C264475C11
1.375,3.552 1.073,4.313 1.073,4.313 1.646,3.563 true 0.906,4.281 1.219,4.479 0.313,0.198 10 false *a
*a Buckle


Using a plastic hammer, bend the buckle to secure the lever and confirm that the tip of the lever is aligned with the buckle as shown in the illustration.

NOTICE:
·

Do not use excessive force when tapping with the plastic hammer.

·

Do not damage the front axle outboard joint boot.




Hide 43474E 4.INSTALL FRONT DRIVE SHAFT DAMPER

a.
C378898C01
1.417,1.688 1.417,1.313 false 0.729,1.688 0.729,1.375 false 0.208,1.688 0.208,1.313 false 1.521,0.323 1.677,0.521 0.156,0.198 10 false A 1.365,1.698 1.677,1.896 0.313,0.198 10 false *1 0.667,1.698 0.979,1.896 0.313,0.198 10 false *2 0.125,1.698 0.438,1.896 0.313,0.198 10 false *1
*1 Front Drive Shaft Damper Clamp
*2 Front Drive Shaft Damper


Temporarily install the front drive shaft damper and 2 new front drive shaft damper clamps to the front drive outboard joint shaft assembly as shown in the illustration.


b.

Set the dimension (A) as specified below.

Dimension (A):
for LH Side 256.9 to 260.9 mm (10.12 to 10.27 in.)
for RH Side 261.4 to 265.4 mm (10.30 to 10.44 in.)



Hide 43474G 5.INSTALL FRONT DRIVE SHAFT DAMPER CLAMP

a.

Secure the drive shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



b.

Install the 2 front drive shaft damper clamps to the front drive shaft damper.

NOTICE:

Be sure to install the clamps in the correct position.



c.
C314741C05
0.51,1.844 0.698,1.938 0.698,1.938 1,1.76 false 0.635,1.938 0.948,2.094 0.313,0.156 10 false *a
*a Claw


Using needle-nose pliers, engage each claw to install the 2 front drive shaft damper clamps as shown in the illustration.

NOTICE:
·

Be sure to install the clamps in the correct position.

·

Do not damage the front drive shaft damper.

·

Do not damage the claws.




Hide 43040 6.INSTALL FRONT DRIVE INBOARD JOINT ASSEMBLY

a.
C274277C02
0.688,1.875 0.688,1.333 false 1.698,1.854 1.698,1.615 false 2.49,1.875 2.49,1.667 false 2.927,1.885 2.927,1.25 false 0.625,1.896 0.938,2.052 0.313,0.156 10 *1 1.635,1.896 1.948,2.052 0.313,0.156 10 *2 2.417,1.906 2.729,2.063 0.313,0.156 10 *3 2.875,1.896 3.188,2.052 0.313,0.156 10 *a
*1 Front Axle Inboard Joint Boot Clamp
*2 Front Axle Inboard Joint Boot
*3 Front No. 2 Axle Inboard Joint Boot Clamp
*a Protective Tape
V100135

Outboard Joint Side
V100136

Inboard Joint Side


Install new parts to the front drive outboard joint shaft assembly in the following order:

i.

Front axle inboard joint boot clamp


ii.

Front axle inboard joint boot


iii.

Front No. 2 axle inboard joint boot clamp



b.

Secure the drive shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



c.

Remove the protective tape.


d.
C378927C01
1.438,1.656 2.177,1.969 2.177,1.969 2.021,1.344 true 2.219,1.927 2.531,2.125 0.313,0.198 10 false *a
*a Matchmark


Align the matchmarks and install the tripod joint to the front drive outboard joint shaft assembly.

NOTICE:

Face the serrated side of the tripod joint outward and install it to the outboard joint end.



e.

Using a brass bar and a hammer, install the tripod joint to the front drive outboard joint shaft assembly.

NOTICE:
·

Do not tap the rollers.

·

Keep the tripod joint free of foreign matter.

·

Make sure to install the tripod joint in the correct direction.




f.
F045046

Using a snap ring expander, install a new shaft snap ring to the front drive outboard joint shaft assembly.


g.

Pack the front drive inboard joint assembly and front axle inboard boot with grease.

Standard Grease Capacity:

205 to 215 g (7.24 to 7.58 oz)



h.
C374772C02
1.74,0.896 1.198,0.292 1.198,0.292 2.042,0.521 false 1,0.167 1.313,0.365 0.313,0.198 10 false *a
*a Matchmark


Align the matchmarks and install the front drive inboard joint assembly to the front drive outboard joint shaft assembly.


Hide 7.INSTALL FRONT AXLE INBOARD JOINT BOOT

a.

When a jig is supplied with the front drive shaft inboard joint boot kit:

i.
C377237C01
0.094,0.156 0.406,0.354 0.313,0.198 10 false *A 0.146,2.552 0.458,2.75 0.313,0.198 10 true *B
*A for LH Side
*B for RH Side
V100144

Jig


Using a jig, install the front axle inboard joint boot to the front drive inboard joint assembly.

NOTICE:
·

Keep the grooves free of grease.

·

Keep the inside of the front axle inboard joint boot free of foreign matter.

·

If the front axle inboard joint boot is not installed at the position indicated by the jig, damage to the front axle inboard joint boot may result.

·

Place the jig at several points around the circumference of the front drive inboard joint assembly to check that the front axle inboard joint boot is installed to the correct position.





b.

When a jig is not supplied with the front drive shaft inboard joint boot kit:

i.

Install the front axle inboard joint boot to the front drive inboard joint assembly.


ii.
C375417C01
0.271,0.271 0.646,0.51 0.375,0.24 10 false *A 0.24,2 0.615,2.24 0.375,0.24 10 false *B 1.885,0.313 2.26,0.542 0.375,0.229 10 false A 1.927,1.938 2.302,2.167 0.375,0.229 10 false A
*A for LH Side
*B for RH Side


Adjust the position of the front axle inboard joint boot so that the dimension (A) is as specified.

Dimension (A):
for LH Side 51.8 to 52.2 mm (2.04 to 2.05 in.)
for RH Side 66.8 to 67.2 mm (2.63 to 2.64 in.)


NOTICE:
·

Keep the grooves free of grease.

·

Keep the inside of the front axle inboard joint boot free of foreign matter.

·

If the front axle inboard joint boot is installed while the dimension (A) is not as specified, damage to the front axle inboard joint boot may result.





Hide 8.INSTALL FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP

CAUTION:
·

Wear protective gloves when installing the front No. 2 axle inboard joint boot clamp.

·

If protective gloves are not worn, injuries may occur.



NOTICE:

New front No. 2 axle inboard joint boot clamp is coated with lubricant. Do not remove the lubricant.


a.

Install the front No. 2 axle inboard joint boot clamp to the front axle inboard joint boot.

HINT:
C375365C01
1.688,0.531 1.958,0.302 false 0.677,0.833 1.083,0.833 false 0.406,2.656 0.938,2.656 false 2,0.188 2.365,0.406 0.365,0.219 10 false *a 0.5,0.729 0.813,0.927 0.313,0.198 10 false *1 0.229,2.552 0.542,2.75 0.313,0.198 10 false *2 1.698,1.094 2.01,1.281 0.313,0.188 10 false A 2.729,3.021 3.042,3.208 0.313,0.188 10 false A 0.635,3.021 0.948,3.208 0.313,0.188 10 false A
*1 Front No. 2 Axle Inboard Joint Boot Clamp
*2 Front Axle Inboard Joint Boot
*a Bending Point


To make installation easier, align the bending point of the lever of the front No. 2 axle inboard joint boot clamp with any of the positions indicated by the arrows (A) shown in the illustration.



b.
C375366C01
1.042,0.781 1.667,0.781 true 0.865,0.677 1.177,0.875 0.313,0.198 10 false *a
*a Welded Area


Temporarily bend the lever of the front No. 2 axle inboard joint boot clamp.

NOTICE:
·

Make sure the front No. 2 axle inboard joint boot clamp is positioned correctly within the groove of the front axle inboard joint boot as far toward the inside of the vehicle as possible.

·

Before bending the lever, confirm that the front No. 2 axle inboard joint boot clamp and the lever are not deformed or damaged.



HINT:

When temporarily bending the lever, push the lever at the welded area.



c.
C375368

Using water pump pliers, temporarily secure the front No. 2 axle inboard joint boot clamp by pinching the front No. 2 axle inboard joint boot clamp until a click sound is heard.

NOTICE:
·

Do not damage the front axle inboard joint boot.

·

To avoid deformation of the front No. 2 axle inboard joint boot clamp, set one tip of the water pump pliers on the welded area of the lever.



HINT:
·

As the front No. 2 axle inboard joint boot clamp is tightened, the tip of the water pump pliers will slide along the front No. 2 axle inboard joint boot clamp until it contacts the protrusion.

·

Set the water pump pliers to an appropriate size before tightening the front No. 2 axle inboard joint boot clamp.




d.
C378931C01
2.594,0.635 2.073,0.271 2.073,0.271 2.792,0.625 true 1.885,0.177 2.177,0.417 0.292,0.24 10 false *a
*a Buckle


Using a plastic hammer, bend the buckle to secure the lever.

NOTICE:
·

Do not use excessive force when tapping with the plastic hammer.

·

Do not damage the front axle inboard joint boot.

·

Check the front axle inboard joint boot is installed to the correct position.




Hide 43448F 9.INSTALL FRONT AXLE INBOARD JOINT BOOT CLAMP

NOTICE:

New front axle inboard joint boot clamp is coated with lubricant. Do not remove the lubricant.


a.
C375254C01
0.271,0.333 0.646,0.573 0.375,0.24 10 false *A 0.146,1.635 0.521,1.875 0.375,0.24 10 false *B 1.448,1.188 1.677,1.5 0.229,0.313 10 false A 1.49,2.531 1.719,2.844 0.229,0.313 10 false A
*A for LH Side
*B for RH Side


Check whether the dimension (A) of each drive shaft is within specification.

Dimension (A):
for LH Side 598.2 to 608.2 mm (1.97 to 1.99 ft.)
for RH Side 897.0 to 907.0 mm (2.95 to 2.97 ft.)



b.

Install the front axle inboard joint boot clamp to the front axle inboard joint boot.


c.
C379252

Using a screwdriver, install the front axle inboard joint boot clamp.

NOTICE:

Do not damage the front axle inboard joint boot.