Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING VALVE › from 2021.02
RM33C0E _53 Suspension _065440 TIRE PRESSURE MONITORING _0329004 TIRE PRESSURE WARNING VALVE A

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING VALVE  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during tire pressure warning valve and transmitter removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Tire pressure warning valve and transmitter
·

Register Transmitter ID

·

Initialize tire pressure warning system


·

When DTC detection conditions of "transmitter ID not received" DTC are met, TPWS indicator blinks for 1 minute, and then illuminates.

·

Tire pressure warning function


(Click here)for Registration
(Click here)for Initialization

PROCEDURE

Hide 1.REMOVE WHEEL ASSEMBLY

Hide 42607 2.REMOVE TIRE PRESSURE WARNING VALVE AND TRANSMITTER (for Type A)

a.

Remove the tire valve cap.

NOTICE:

Keep the removed tire valve cap.



b.

Remove the valve core to release the air from the tire.

NOTICE:

Make sure that a sufficient amount of air has been released.



c.
C180021C06
0.531,0.885 0.979,0.885 false 2.427,0.885 2.958,0.885 false 0.302,0.823 0.604,1.01 0.302,0.188 10 false *1 2.99,0.833 3.302,0.99 0.313,0.156 10 false *a 2.094,1.781 2.406,1.938 0.313,0.156 10 false *b
*1 Tire
*a Shoe
*b 10 to 20 mm (0.394 to 0.787 in.)


Using a tire remover, remove the tire from the disc wheel.

NOTICE:
·

Be careful not to damage the tire pressure warning valve and transmitter due to interference between the valve and the tire bead.

·

Set the tire remover shoe as shown in the illustration.




d.
C402143

Using a T10 "TORX" driver, remove the bolt and tire pressure monitor sensor from the tubeless tire valve.


e.
C402144C01
0.458,2.354 1,2.354 false 0.271,2.281 0.583,2.479 0.313,0.198 10 false *1
*1 Tubeless Tire Valve
V100155

Cutting Area


Cut the tubeless tire valve and remove it by pulling from the outer side of the disc wheel as shown in the illustration.


Hide 42607 3.REMOVE TIRE PRESSURE WARNING VALVE AND TRANSMITTER (for Type B)

a.

Remove the tire valve cap.

NOTICE:

Keep the removed tire valve cap.



b.

Remove the valve core to release the air from the tire.

NOTICE:

Make sure that a sufficient amount of air has been released.



c.

Using a 11 mm deep socket wrench, remove the nut and washer.


d.

Drop the tire pressure warning valve and transmitter with grommet into the tire.

HINT:

The grommet may remain attached to the rim.



e.
C180021C11
0.531,0.885 0.979,0.885 false 2.427,0.885 2.958,0.885 false 0.396,0.781 0.698,0.969 0.302,0.188 10 false *1 3.01,0.781 3.323,0.938 0.313,0.156 10 false *a 2.094,1.771 2.406,1.927 0.313,0.156 10 false *b
*1 Tire
*a Shoe
*b 10 to 20 mm (0.394 to 0.787 in.)


Using a tire remover, remove the tire from the disc wheel.

NOTICE:
·

Be careful not to damage the tire pressure warning valve and transmitter due to interference between the valve and the tire bead.

·

Set the tire remover shoe as shown in the illustration.




f.

Take out the tire pressure warning valve and transmitter with grommet from the tire.


g.

Remove the grommet from the tire pressure warning valve and transmitter.


h.
C411111

Using a T10 "TORX" driver, remove the bolt and tire pressure monitor sensor from the tubeless tire valve.