Home › Engine / Hybrid System › A25A-FXS (ENGINE CONTROL) › SFI SYSTEM (w/ Canister Pump Module) › 2021.02–2022.01
RM33C0E _51 Engine / Hybrid System _065419 A25A-FXS ENGINE CONTROL _0332275 SFI SYSTEM(w/ Canister Pump Module) C

A25A-FXS ENGINE CONTROL  SFI SYSTEM(w/ Canister Pump Module)  P059A71  Active Grille Air Shutter "A" Actuator Stuck  P059A79  Active Grille Air Shutter "A" Mechanical Linkage Failure  


DESCRIPTION

The grille shutter system is composed of the radiator shutter sub-assembly and swing grille actuator assembly.

When the certain vehicle conditions are met, the grille shutter system operates the swing grille actuator assembly to open and close the radiator shutter sub-assembly and control the volume of air flowing through the radiator assembly into the engine compartment. This results in increased thermal efficiency and increased fuel economy due to reduced aerodynamic drag. This control is performed based on signals received via CAN communication: vehicle speed signal, engine coolant temperature signal, hybrid inverter coolant temperature signal, ambient temperature signal and refrigerant pressure.

Control List
Control Description
Closing Operation Control When the grille shutter is open and the vehicle conditions are met, the grille shutter closes in order to improve fuel economy (reduce air resistance) and reduce engine warm up time.
Opening Operation Control When the grille shutter is closed and the vehicle conditions are met, the grille shutter opens to ensure radiator and engine cooling air.
Ignition Switch Off-linked Opening Operation Control When the power switch is turned off and the vehicle is stopped with the grille shutter closed, the grille shutter opens.
Winter Control Mode During operation in low temperatures when there is a possibility of the grille shutter being stuck due to being frozen, a malfunction judgment is not made even though it is detected that the grille shutter is stuck.
Retry Operation If a mechanical malfunction is detected during a grille shutter operation, the operation will be attempted again.

A473418E03
3.948,0.604 4.292,0.354 4.292,0.354 4.479,0.354 false 4.563,0.271 6.594,1.281 2.031,1.01 10 false Grille Shutter Motor (Swing Grille Actuator Assembly) 3.396,1.417 4.875,1.844 1.479,0.427 10 false Motor Drive Circuit 3.573,2.375 5.052,2.802 1.479,0.427 10 false Motor Drive 3.26,3.229 4.646,3.688 1.385,0.458 10 false Power Supply Voltage Monitor Circuit 3.323,4.583 4.708,5.042 1.385,0.458 10 false Power Supply Circuit 0.094,4.698 1.583,5.198 1.49,0.5 10 false from G/SHUTTER fuse 1.896,4.51 2.771,5.052 0.875,0.542 10 false +B 1.802,5.198 2.677,5.74 0.875,0.542 10 false GND 1.854,6.073 2.729,6.615 0.875,0.542 10 false LIN 3.323,5.938 4.563,6.5 1.24,0.563 10 false LIN Communication Circuit 0.865,6.24 2.104,6.802 1.24,0.563 10 false to ECM 5.656,3.99 6.417,4.385 0.76,0.396 10 false CPU 2.917,7.698 6.125,8.042 3.208,0.344 10 false Grille Shutter ECU (Swing Grille Actuator Assembly) 0.49,8.417 2.229,8.656 1.74,0.24 10 false : LIN Communication Line

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P059A71 Active Grille Air Shutter "A" Actuator Stuck A signal from the swing grille actuator assembly indicating that the grille shutter is stuck is detected for 7.86 seconds or more (2 trip detection logic).
·

Radiator shutter assembly

·

ECM


Comes on DTC stored SAE Code: P059F
P059A79 Active Grille Air Shutter "A" Mechanical Linkage Failure A signal from the swing grille actuator assembly indicating a malfunction is detected for 7.86 seconds or more (2 trip detection logic).
·

Radiator shutter assembly

·

ECM


Comes on DTC stored SAE Code: P059F

MONITOR DESCRIPTION

When the swing grille actuator assembly detects that the grille shutter is stuck or there is a malfunction, a DTC request is sent to the ECM and the ECM stores a DTC.

MONITOR STRATEGY

Required Sensors/Components (Main) Swing grille actuator assembly
Radiator shutter sub-assembly
Frequency of Operation Once per driving cycle

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG).

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the power switch off and wait for at least 30 seconds.

6.

Turn the power switch on (IG).

7.

Turn the GTS on.

8.

Enter the following menus: Powertrain / Engine / Utility / Switch Grille Shutter Control Mode.

9.

According to the display on the GTS, change the grille shutter control mode from normal mode to maintenance mode.

10.

Enter the following menus: Powertrain / Engine / Utility / Grille Shutter Initialization / Initialization operation (Nominal Torque).

11.

According to the display on the GTS, perform initialization.

12.

Enter the following menus: Powertrain / Engine / Trouble Codes.

13.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



14.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

15.

Input the DTC: P059A71 or P059A79.

16.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system has a malfunction.




CAUTION / NOTICE / HINT

NOTICE:
·

In order to ensure safety, before performing troubleshooting or removing the radiator shutter assembly, change the grille shutter control mode to maintenance mode.

·

Vehicle Control History may be stored in the hybrid vehicle control ECU assembly if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the Freeze Frame Data and Vehicle Control History can be useful for troubleshooting.

- for Nickel Metal Hydride Battery: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>VEHICLE CONTROL HISTORY

- for Lithium-ion Battery: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY)>VEHICLE CONTROL HISTORY

(Select Powertrain in Health Check and then check the time stamp data.)

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>DTC CHECK / CLEAR

·

If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU assembly, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.

- for Nickel Metal Hydride Battery: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>VEHICLE CONTROL HISTORY

- for Lithium-ion Battery: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY)>VEHICLE CONTROL HISTORY



HINT:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.PERFORM UTILITY USING GTS (SWITCH GRILLE SHUTTER CONTROL MODE)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Utility / Switch Grille Shutter Control Mode.

Powertrain > Engine > Utility
Tester Display
Switch Grille Shutter Control Mode
50005 372 4672

e.

According to the display on the GTS, change the grille shutter control mode from normal mode to maintenance mode.


Result:
Proceed to
NEXT



NEXT

2.INSPECT GRILLE SHUTTER (FOREIGN MATTER AND ICE)
2.INSPECT GRILLE SHUTTER (FOREIGN MATTER AND ICE)
a.

Check the area around the shutters and the links of the grille shutter for foreign matter and ice.

OK:

No foreign matter or ice.



Result:
Proceed to
OK
NG



OK

3.PERFORM UTILITY USING GTS (GRILLE SHUTTER INITIALIZATION)

NG

6.REMOVE FOREIGN MATTER OR ICE (CLEAN GRILLE SHUTTER)
3.PERFORM UTILITY USING GTS (GRILLE SHUTTER INITIALIZATION)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Utility / Grille Shutter Initialization.

Powertrain > Engine > Utility
Tester Display
Grille Shutter Initialization
50005 372 4673

e.

According to the display on the GTS, perform initialization (nominal torque).


Result:
Proceed to
NEXT



NEXT

4.CLEAR DTC
4.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

b.

Turn the power switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

5.CHECK DTC OUTPUT (DTC P059A71 OR P059A79)
5.CHECK DTC OUTPUT (DTC P059A71 OR P059A79)
a.

Turn the power switch on (IG).


b.

Turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.


d.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTCs are not output A
DTC P059A71 and/or P059A79 is output B



HINT:

Perform "Switch Grille Shutter Control Mode and Grille Shutter Initialization" after replacing the radiator shutter assembly.

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>INITIALIZATION



A

8.READ VALUE USING GTS (GRILLE SHUTTER CONTROL MODE)

B

REPLACE RADIATOR SHUTTER ASSEMBLY

6.REMOVE FOREIGN MATTER OR ICE (CLEAN GRILLE SHUTTER)
a.

Remove any foreign matter and/or ice from the area around the shutters and the links of the grille shutter.


Result:
Proceed to
NEXT



NEXT

7.CLEAR DTC
7.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

8.READ VALUE USING GTS (GRILLE SHUTTER CONTROL MODE)
8.READ VALUE USING GTS (GRILLE SHUTTER CONTROL MODE)
a.

Turn the power switch on (IG).


b.

Turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Utility / Switch Grille Shutter Control Mode.

Powertrain > Engine > Utility
Tester Display
Switch Grille Shutter Control Mode
50005 372 4672

d.

According to the display on the GTS, change the grille shutter control mode from maintenance mode to normal mode.


e.

Enter the following menus: Powertrain / Engine / Data List /Grille Shutter Control Mode.

Powertrain > Engine > Data List
Tester Display
Grille Shutter Control Mode
50003 372 1304

f.

Read the value displayed on the GTS.

Standard:
GTS Display Specified Condition
Grille Shutter Control Mode Normal


Result:
Proceed to
NEXT




NEXT

END