Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › 2021.02–2021.08
RM33C0E _51 Engine / Hybrid System _065434 CRUISE CONTROL _0328967 DYNAMIC RADAR CRUISE CONTROL SYSTEM U

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  TERMINALS OF ECU  


CHECK HYBRID VEHICLE CONTROL ECU ASSEMBLY


B344905N26
1.344,0.094 1.729,0.313 0.385,0.219 2.781,0.094 3.167,0.313 0.385,0.219 4.208,0.094 4.594,0.313 0.385,0.219 5.469,0.094 5.854,0.313 0.385,0.219 1.417,0.135 1.875,0.333 0.458,0.198 10 false A28 2.854,0.135 3.313,0.333 0.458,0.198 10 false A29 4.281,0.135 4.594,0.333 0.313,0.198 10 false K69 5.542,0.135 5.854,0.333 0.313,0.198 10 false K70

a.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbols) Wiring Color Terminal Description Condition Specified Condition
A28-15 (STP) - K69-6 (E1) LA-G - W-B Stop light switch signal Brake pedal depressed 7.5 to 14 V
Brake pedal released Below 1 V
A29-28 (ST1-) - K69-6 (E1) LG - W-B Stop light switch signal Power switch on (IG), brake pedal depressed Below 1 V
Power switch on (IG), brake pedal released 7.5 to 14 V
K69-28 (CCS) - K69-6 (E1) GR - W-B Steering pad switch circuit Cruise control switch not pushed 1 MΩ or higher
Cruise control main switch pushed Below 2.5 Ω
CANCEL switch pushed 235 to 245 Ω
+RES switch pushed 617 to 643 Ω
-SET switch pushed 1509 to 1571 Ω



CHECK FORWARD RECOGNITION CAMERA


NOTICE:
·

DTCs may be output when connectors are disconnected during inspection. Therefore, be sure to clear the DTCs using the GTS once the inspection has been completed.

·

Do not apply excessive force to the forward recognition camera connector.



B472992N01
2.073,0.833 2.458,1.042 0.385,0.208 2.188,0.865 2.5,1.063 0.313,0.198 10 false V6

a.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
V6-3 (LKSW) - V6-10 (GND) V - LA*1
V - W-B*2
Steering pad switch assembly signal (distance control signal) Power switch on (IG), steering pad switch assembly (vehicle-to-vehicle distance control switch) off 4.75 to 5.25 V
Power switch on (IG), steering pad switch assembly (vehicle-to-vehicle distance control switch) on Below 1 V
V6-7 (IGB) - V6-10 (GND) LA-P - LA*1
LA-P - W-B*2
Power source Power switch on (IG) 11 to 14 V
Power switch off Below 1 V
V6-10 (GND) - Body ground LA - Body ground*1
W-B - Body ground*2
Ground Always Below 1 Ω

*1: Through No. 29 Junction Connector

*2: Not through No. 29 Junction Connector