Home › Engine / Hybrid System › CRUISE CONTROL › LANE TRACING ASSIST SYSTEM › from 2021.02
RM33C0E _51 Engine / Hybrid System _065434 CRUISE CONTROL _0465300 LANE TRACING ASSIST SYSTEM Y

CRUISE CONTROL  LANE TRACING ASSIST SYSTEM  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

HINT:
·

Use the following procedure to troubleshoot the lane tracing assist system.

·

*: Use the GTS.



PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Proceed to
NEXT



NEXT

2.CUSTOMER PROBLEM ANALYSIS
2.CUSTOMER PROBLEM ANALYSIS
HINT:
·

In troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.

·

Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.

·

The following 5 items are important points for problem analysis:

What Vehicle model, system name
When Date, time, occurrence frequency
Where Road conditions
Under what conditions? Driving conditions, weather conditions
How did it happen? Problem symptoms



Result:
Proceed to
NEXT



NEXT

3.PRE-CHECK
3.PRE-CHECK
a.

Measure the auxiliary battery voltage with the power switch off.

Standard voltage:

11 to 14 V


HINT:

If the voltage is below 11 V, recharge or replace the auxiliary battery before proceeding to the next step.



b.

Check the fuses and relays.


c.

Check the connector connections and terminals to make sure that there are no abnormalities such as loose connections, deformation, etc.


Result:
Proceed to
NEXT



NEXT

4.CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*
4.CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*
a.

Using the GTS, check for CAN communication system DTCs.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
CAN DTCs are not output A
CAN DTCs are output B



A

5.CHECK FOR DTCs*

B

5.CHECK FOR DTCs*
a.

Using the GTS, check for DTCs.

Chassis > Lane Control > Clear DTCs
50002 418

b.

If a DTC is output, record the DTC.


Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

6.CHECK VEHICLE CONTROL HISTORY*

B

7.RECHECK FOR DTCs*
6.CHECK VEHICLE CONTROL HISTORY*
a.

Using the GTS, check for Vehicle Control History (RoB).

Chassis > Lane Control > Utility
Tester Display
Vehicle Control History (RoB)
50005 418 55

b.

If the Vehicle Control History (RoB) is output, record it.


Result:
Result Proceed to
Vehicle Control History (RoB) is not output A
Vehicle Control History (RoB) is output B



A

B

8.RECHECK VEHICLE CONTROL HISTORY*
7.RECHECK FOR DTCs*
a.

Using the GTS, clear the DTCs.

Chassis > Lane Control > Clear DTCs
50002 418

b.

Reproduce the detection conditions of the recorded DTC.

HINT:

Refer to the flowchart of each diagnosis code for the diagnosis code detection condition.

Click hereEngine / Hybrid System>CRUISE CONTROL>LANE TRACING ASSIST SYSTEM>DIAGNOSTIC TROUBLE CODE CHART



c.

Using the GTS, check if the DTCs are output again.

Click hereEngine / Hybrid System>CRUISE CONTROL>LANE TRACING ASSIST SYSTEM>DTC CHECK / CLEAR

Chassis > Lane Control > Trouble Codes
50001 418

Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

8.RECHECK VEHICLE CONTROL HISTORY*

B

8.RECHECK VEHICLE CONTROL HISTORY*
a.

Using the GTS, clear the Vehicle Control History (RoB).

Chassis > Lane Control > Utility
Tester Display
Vehicle Control History (RoB)
50005 418 55

b.

Using the GTS, check for Vehicle Control History (RoB).

Chassis > Lane Control > Utility
Tester Display
Vehicle Control History (RoB)
50005 418 55

Result:
Result Proceed to
Vehicle Control History (RoB) is not output A
Vehicle Control History (RoB) is output B



A

B