Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM (w/ Automatic Headlight Beam Level Control System) › from 2021.02
RM33C0E _59 Vehicle Exterior _065472 LIGHTING (EXT) _0331112 LIGHTING SYSTEM(w/ Automatic Headlight Beam Level Control System) L

LIGHTING (EXT)  LIGHTING SYSTEM(w/ Automatic Headlight Beam Level Control System)  PRECAUTION  


PRECAUTION FOR DISCONNECTING CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL


NOTICE:

When disconnecting the cable from the negative (-) auxiliary battery terminal, initialize the following systems after the cable is reconnected.

System Name See Procedure
Lane Tracing Assist System (Click here)
Pre-collision System
Parking Assist Monitor System
Panoramic View Monitor System



PRECAUTION FOR BULB REPLACEMENT


a.

Always prepare a new bulb for immediate replacement. While replacing the bulb, the lens may attract dust and moisture if the bulb is removed from the vehicle for a long time.


b.

Always replace a bulb with another bulb of the same wattage.


c.

If only replacing the bulb on one side, differences in brightness and lighting color between the right and left sides may occur.


d.

Securely install the socket after bulb replacement. The lens may become cloudy or the light assembly may fill with water through gaps around the socket if it is not installed securely.



PRECAUTIONS FOR AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM


a.

If any of the following are performed, it is necessary to initialize the headlight ECU sub-assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/ Automatic Headlight Beam Level Control System)>INITIALIZATION

·

Replacement of the rear height control sensor sub-assembly LH

·

Removal/installation of the rear height control sensor sub-assembly LH

·

Work that changes the vehicle height such as replacement of suspension components



b.

If the headlight ECU sub-assembly LH has been replaced, it is necessary to synchronize the vehicle information and initialize the headlight ECU sub-assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/ Automatic Headlight Beam Level Control System)>INITIALIZATION



PRECAUTION FOR AUTOMATIC HIGH BEAM SYSTEM (w/ Automatic High Beam System)


a.

General Description

The automatic high beam system is a system that helps ensure visibility by automatically turning the high beam headlights on and off. Additionally, due to control limitations of the automatic high beam system, it may be necessary to manually turn the high beam headlights on and off. For safety reasons, make sure to turn the high beam headlights on and off manually according to the driving conditions.


b.

Conditions Unsuitable for Using Automatic High Beam System

Under the following conditions, the automatic high beam system might not detect other vehicles or lights correctly, or the high beam headlights might cause glare or flash pedestrians or the occupants of other vehicles. Manual operation should be considered.

Factor Condition
Weather/Climate
·

When driving in bad weather (rain, snow, fog, sandstorms, etc.).

·

The temperature inside the vehicle is high.

·

The taillights of a proceeding vehicle are obscured by snow, etc.


Front windshield Refer to Front Camera System.
(Click here)
Forward recognition camera Refer to Front Camera System.
(Click here)
Nearby vehicles or lights
·

When lights similar to headlights or taillights are in the vicinity of the vehicle.

·

When a nearby vehicle has no lights or its lights are off.

·

When a vehicle in front has misaligned lights, or its lights are changing color.

·

When a vehicle in front has extremely dirty headlights or taillights.


Road conditions
·

When driving in areas where the conditions often change between bright and dark.

·

When driving on hilly roads.

·

When driving on winding roads or around sharp curves.

·

When driving on bumpy roads (cobblestone paving, gravel roads, rough unpaved roads, etc.).

·

When highly reflective objects are in front of the vehicle (mirrors, road signs, etc.).


Own vehicle
·

When the headlights are damaged, deformed or dirty.

·

When the vehicle posture is abnormal (posture has changed due to the vehicle being fully loaded, a trailer being towed, road conditions, etc.).

·

When the vehicle has other malfunctions or has been modified.


Automatic high beam system Malfunction:
When the automatic high beam indicator light on the combination meter assembly is off and "Headlight System Malfunction Visit Your Dealer" is displayed on the multi-information display.
Others:
·

When the automatic high beam system does not seem to be turning the high beam headlights on and off properly.

·

When the automatic high beam system is frequently turning the high beam headlights on and off.

·

When the glare from the high beam headlights would disturb pedestrians or the drivers of other vehicles.





PRECAUTION FOR FRONT CAMERA SYSTEM (w/ Automatic High Beam System)


Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA SYSTEM>PRECAUTION