Home › Vehicle Exterior › MIRROR (EXT) › OUTER REAR VIEW MIRROR › from 2021.02
RM33C0E _59 Vehicle Exterior _065470 MIRROR (EXT) _0332579 OUTER REAR VIEW MIRROR G

MIRROR (EXT)  OUTER REAR VIEW MIRROR  INSPECTION  


PROCEDURE

Hide 87910 1.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH

a.

Check the operation of the mirror surface. (for 7 Pin Connector)

NOTICE:

If the mirror surface is fully turned to the right, left, upward or downward position, the motor slips and produces a clicking noise. This is not a malfunction.


i.
B319940C11
2.042,2.365 2.042,1.938 2.042,1.938 2.188,1.938 true 1.948,2.365 1.948,1.594 1.948,1.594 2.188,1.594 true 1.833,2.406 1.833,1.833 1.833,1.833 1.688,1.833 true 1.271,2.135 1.719,2.469 0.448,0.333 10 false *a 1.427,1.76 1.938,2.156 0.51,0.396 10 false MV 2.25,1.844 2.885,2.156 0.635,0.313 10 false MH 2.25,1.521 2.74,1.823 0.49,0.302 10 false M+
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


Disconnect the outer rear view mirror assembly RH connector.


ii.

Apply auxiliary battery voltage and check the operation of the mirror surface.

OK:
Auxiliary Battery Connection Specified Condition
Auxiliary battery positive (+) → Terminal 3 (MV)
Auxiliary battery negative (-) → Terminal 7 (M+)
Turns upward
Auxiliary battery positive (+) → Terminal 7 (M+)
Auxiliary battery negative (-) → Terminal 3 (MV)
Turns downward
Auxiliary battery positive (+) → Terminal 6 (MH)
Auxiliary battery negative (-) → Terminal 7 (M+)
Turns left
Auxiliary battery positive (+) → Terminal 7 (M+)
Auxiliary battery negative (-) → Terminal 6 (MH)
Turns right


If the result is not as specified, replace the outer rear view mirror assembly RH.



b.

Check the operation of the mirror surface. (for 11 Pin Connector)

NOTICE:

If the mirror surface is fully turned to the right, left, upward or downward position, the motor slips and produces a clicking noise. This is not a malfunction.


i.
B319979C20
2.469,2.531 2.469,1.948 2.469,1.948 2.271,1.948 true 2.573,2.531 2.573,1.531 2.573,1.531 2.771,1.531 true 2.677,2.531 2.677,1.948 2.677,1.948 2.875,1.948 true 2.052,1.865 2.313,2.042 0.26,0.177 10 false MH 2.813,1.458 3.094,1.656 0.281,0.198 10 false M+ 2.927,1.875 3.208,2.156 0.281,0.281 10 false MV 1.521,2.083 1.688,2.229 0.167,0.146 10 false *a
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


Disconnect the outer rear view mirror assembly RH connector.


ii.

Apply auxiliary battery voltage and check the operation of the mirror surface.

OK:
Auxiliary Battery Connection Specified Condition
Auxiliary battery positive (+) → Terminal 6 (MV)
Auxiliary battery negative (-) → Terminal 5 (M+)
Turns upward
Auxiliary battery positive (+) → Terminal 5 (M+)
Auxiliary battery negative (-) → Terminal 6 (MV)
Turns downward
Auxiliary battery positive (+) → Terminal 4 (MH)
Auxiliary battery negative (-) → Terminal 5 (M+)
Turns left
Auxiliary battery positive (+) → Terminal 5 (M+)
Auxiliary battery negative (-) → Terminal 4 (MH)
Turns right


If the result is not as specified, replace the outer rear view mirror assembly RH.



c.

Check the operation of the mirror surface. (for 16 Pin Connector)

NOTICE:

If the mirror surface is fully turned to the right, left, upward or downward position, the motor slips and produces a clicking noise. This is not a malfunction.


i.
B485586C05
1.479,1.885 1.219,1.885 1.219,1.885 1.219,2.563 true 0.917,3.24 1.219,3.24 1.219,3.24 1.219,2.802 true 1.635,3.229 1.333,3.229 1.333,3.229 1.333,2.792 true 1.51,1.802 1.823,2 0.313,0.198 10 false MV 0.625,1.99 0.938,2.188 0.313,0.198 10 false *a 0.677,3.156 0.99,3.354 0.313,0.198 10 false MH 1.688,3.135 2,3.333 0.313,0.198 10 false M+
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


Disconnect the outer rear view mirror assembly RH connector.


ii.

Apply auxiliary battery voltage and check the operation of the mirror surface.

OK:
Auxiliary Battery Connection Specified Condition
Auxiliary battery positive (+) → Terminal 1 (MV)
Auxiliary battery negative (-) → Terminal 10 (M+)
Turns upward
Auxiliary battery positive (+) → Terminal 10 (M+)
Auxiliary battery negative (-) → Terminal 1 (MV)
Turns downward
Auxiliary battery positive (+) → Terminal 9 (MH)
Auxiliary battery negative (-) → Terminal 10 (M+)
Turns left
Auxiliary battery positive (+) → Terminal 10 (M+)
Auxiliary battery negative (-) → Terminal 9 (MH)
Turns right


If the result is not as specified, replace the outer rear view mirror assembly RH.



d.

Check the operation of the mirror surface. (for 22 Pin Connector)

NOTICE:

If the mirror surface is fully turned to the right, left, upward or downward position, the motor slips and produces a clicking noise. This is not a malfunction.


i.
B495592C04
2.563,2.552 2.563,1.969 2.563,1.969 2.729,1.969 true 2.49,2.552 2.49,1.719 2.49,1.719 2.74,1.719 true 2.406,2.552 2.406,1.885 2.406,1.885 2.24,1.885 true 2.802,1.885 3.115,2.083 0.313,0.198 10 false MH 2.823,1.635 3.135,1.833 0.313,0.198 10 false M+ 1.99,1.802 2.302,2 0.313,0.198 10 false MV 1.563,2.094 1.875,2.292 0.313,0.198 10 false *a
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


Disconnect the outer rear view mirror assembly RH connector.


ii.

Apply battery voltage and check the operation of the mirror surface.

OK:
Auxiliary Battery Connection Specified Condition
Auxiliary battery positive (+) → Terminal 7 (MV)
Auxiliary battery negative (-) → Terminal 8 (M+)
Turns upward
Auxiliary battery positive (+) → Terminal 8 (M+)
Auxiliary battery negative (-) → Terminal 7 (MV)
Turns downward
Auxiliary battery positive (+) → Terminal 9 (MH)
Auxiliary battery negative (-) → Terminal 8 (M+)
Turns left
Auxiliary battery positive (+) → Terminal 8 (M+)
Auxiliary battery negative (-) → Terminal 9 (MH)
Turns right


If the result is not as specified, replace the outer rear view mirror assembly RH.



e.

Check the operation of the mirror heater. (for 11 Pin Connector)

i.
B319983C23
2.563,2.771 2.563,3.208 2.563,3.208 2.302,3.208 true 2.01,2.5 2.01,1.875 2.01,1.875 2.281,1.875 true 2.333,1.792 2.531,1.979 0.198,0.188 10 false + 2.188,3.125 2.458,3.344 0.271,0.219 10 false E 1.448,2.094 1.708,2.302 0.26,0.208 10 false *a
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


Disconnect the outer rear view mirror assembly RH connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (+) - 11 (E) 25°C (77°F) 10 to 17 Ω


If the result is not as specified, replace the outer rear view mirror assembly RH.


iii.

Connect a cable from the positive (+) auxiliary battery terminal to terminal 2 (+) and the negative (-) auxiliary battery terminal to terminal 11 (E), then check that the mirror becomes warm.

HINT:

It takes a short time for the mirror to become warm.


OK:

Mirror becomes warm.


If the result is not as specified, replace the outer rear view mirror assembly RH.



f.

Check the operation of the mirror heater. (for 16 Pin Connector)

i.
B485587C05
2.031,2.583 2.031,1.813 2.031,1.813 2.427,1.813 true 2.448,3.198 2.021,3.198 2.021,3.198 2.021,2.823 true 0.76,2 1.073,2.198 0.313,0.198 10 false *a 2.49,1.729 2.802,1.927 0.313,0.198 10 false + 2.521,3.104 2.833,3.302 0.313,0.198 10 false -
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


Disconnect the outer rear view mirror assembly RH connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
7 (+) - 15 (-) 25°C (77°F) 10 to 17 Ω


If the result is not as specified, replace the outer rear view mirror assembly RH.


iii.

Connect a cable from the positive (+) battery terminal to terminal 7 and the negative (-) battery terminal to terminal 15, then check that the mirror becomes warm.

HINT:

It takes a short time for the mirror to become warm.


OK:

Mirror becomes warm.


If the result is not as specified, replace the outer rear view mirror assembly RH.



g.

Check the operation of the mirror heater. (for 22 Pin Connector)

i.
B495593C04
2.333,2.563 2.333,1.979 2.333,1.979 2.5,1.979 true 2.167,3.302 2.333,3.302 2.333,3.302 2.333,2.719 true 2.573,1.896 2.729,2.094 0.156,0.198 10 false + 2.042,3.208 2.198,3.406 0.156,0.198 10 false - 1.594,2.021 1.896,2.219 0.302,0.198 10 false *a
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


Disconnect the outer rear view mirror assembly RH connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6 (+) - 17 (-) 25°C (77°F) 10 to 17 Ω


If the result is not as specified, replace the outer rear view mirror assembly RH.


iii.

Connect a cable from the positive (+) battery terminal to terminal 6 (+) and the negative (-) battery terminal to terminal 17 (-), then check that the mirror becomes warm.

HINT:

It takes a short time for the mirror to become warm.


OK:

Mirror becomes warm.


If the result is not as specified, replace the outer rear view mirror assembly RH.



h.

Check the operation of the retractable mirror. (for 7 Pin Connector with Power Retract Mirror)

NOTICE:
·

Disconnect and reconnect the auxiliary battery between each mirror position check.

·

The mirror position cannot be changed manually when the auxiliary battery is connected. To change the mirror position manually, the auxiliary battery must be disconnected first.

·

If the motor is kept energized, even after each mirror position check, it may lead to a motor malfunction. Make sure to disconnect the auxiliary battery immediately after performing each mirror position check.



i.
B504673C04
0.5,3.26 0.667,3.26 0.667,3.26 0.667,2.719 true 0.927,3.26 0.76,3.26 0.76,3.26 0.76,2.719 true 2.604,0.115 2.917,0.313 0.313,0.198 10 false *a 2.958,0.969 3.271,1.167 0.313,0.198 10 false *b 2.833,1.823 3.146,2.021 0.313,0.198 10 false *c 2.385,2.042 2.698,2.24 0.313,0.198 10 false *d 2.021,2.281 2.333,2.479 0.313,0.198 10 false *e 0.229,2.063 0.542,2.26 0.313,0.198 10 false *f 0.292,3.177 0.604,3.375 0.313,0.198 10 false MF 0.979,3.177 1.292,3.375 0.313,0.198 10 false MR
*a (A) Forward Position
*b (B)
*c (C) Driving Position
*d (D)
*e (E) Retracted Position
*f Component without harness connected
(Outer Rear View Mirror Assembly RH)


Disconnect the outer rear view mirror assembly RH connector.


ii.

For each position: Disconnect the auxiliary battery, set the mirror position by hand, connect the auxiliary battery, and check the retractable mirror's movement.

OK:
Auxiliary Battery Connection Condition Specified Condition
Auxiliary battery positive (+) → Terminal 1 (MR)
Auxiliary battery negative (-) → Terminal 2 (MF)
Forward position (A) Moves from (A) to (E)
Auxiliary battery positive (+) → Terminal 2 (MF)
Auxiliary battery negative (-) → Terminal 1 (MR)
Forward position (A) Does not move
Auxiliary battery positive (+) → Terminal 1 (MR)
Auxiliary battery negative (-) → Terminal 2 (MF)
Position between forward position (A) and driving position (C) Moves from (B) to (E)
Auxiliary battery positive (+) → Terminal 2 (MF)
Auxiliary battery negative (-) → Terminal 1 (MR)
Position between forward position (A) and driving position (C) Moves from (B) to (A)
Auxiliary battery positive (+) → Terminal 1 (MR)
Auxiliary battery negative (-) → Terminal 2 (MF)
Driving position (C) Moves from (C) to (E)
Auxiliary battery positive (+) → Terminal 2 (MF)
Auxiliary battery negative (-) → Terminal 1 (MR)
Driving position (C) Does not move
Auxiliary battery positive (+) → Terminal 1 (MR)
Auxiliary battery negative (-) → Terminal 2 (MF)
Position between driving position (C) and retracted position (E) Moves from (D) to (E)
Auxiliary battery positive (+) → Terminal 2 (MF)
Auxiliary battery negative (-) → Terminal 1 (MR)
Position between driving position (C) and retracted position (E) Moves from (D) to (C)
Auxiliary battery positive (+) → Terminal 1 (MR)
Auxiliary battery negative (-) → Terminal 2 (MF)
Retracted position (E) Does not move
Auxiliary battery positive (+) → Terminal 2 (MF)
Auxiliary battery negative (-) → Terminal 1 (MR)
Retracted position (E) Moves from (E) to (C)


If the result is not as specified, replace the outer mirror retractor RH.



i.

Check the operation of the retractable mirror. (for 11 Pin Connector)

NOTICE:
·

Disconnect and reconnect the auxiliary battery between each mirror position check.

·

The mirror position cannot be changed manually when the auxiliary battery is connected. To change the mirror position manually, the auxiliary battery must be disconnected first.

·

If the motor is kept energized, even after each mirror position check, it may lead to a motor malfunction. Make sure to disconnect the auxiliary battery immediately after performing each mirror position check.



i.
B320731C27
0.813,2.792 0.813,3.146 0.813,3.146 0.615,3.146 true 1.104,2.021 0.813,2.021 0.813,2.021 0.823,2.573 true 2.635,0.156 2.865,0.396 0.229,0.24 10 false *a 2.01,2.25 2.271,2.458 0.26,0.208 10 false *e 2.406,2.042 2.604,2.188 0.198,0.146 10 false *d 2.813,1.781 3.021,2 0.208,0.219 10 false *c 2.969,0.938 3.219,1.167 0.25,0.229 10 false *b 0.385,3.063 0.698,3.271 0.313,0.208 10 false MF 1.146,1.927 1.521,2.135 0.375,0.208 10 false MR 0.25,2.104 0.563,2.365 0.313,0.26 10 false *f
*a (A) Forward Position
*b (B)
*c (C) Driving Position
*d (D)
*e (E) Retracted Position
*f Component without harness connected
(Outer Rear View Mirror Assembly RH)


Disconnect the outer rear view mirror assembly RH connector.


ii.

For each position: Disconnect the auxiliary battery, set the mirror position by hand, connect the auxiliary battery, and check the retractable mirror's movement.

OK:
Auxiliary Battery Connection Condition Specified Condition
Auxiliary battery positive (+) → Terminal 3 (MR)
Auxiliary battery negative (-) → Terminal 9 (MF)
Forward position (A) Moves from (A) to (E)
Auxiliary battery positive (+) → Terminal 9 (MF)
Auxiliary battery negative (-) → Terminal 3 (MR)
Forward position (A) Does not move
Auxiliary battery positive (+) → Terminal 3 (MR)
Auxiliary battery negative (-) → Terminal 9 (MF)
Position between forward position (A) and driving position (C) Moves from (B) to (E)
Auxiliary battery positive (+) → Terminal 9 (MF)
Auxiliary battery negative (-) → Terminal 3 (MR)
Position between forward position (A) and driving position (C) Moves from (B) to (A)
Auxiliary battery positive (+) → Terminal 3 (MR)
Auxiliary battery negative (-) → Terminal 9 (MF)
Driving position (C) Moves from (C) to (E)
Auxiliary battery positive (+) → Terminal 9 (MF)
Auxiliary battery negative (-) → Terminal 3 (MR)
Driving position (C) Does not move
Auxiliary battery positive (+) → Terminal 3 (MR)
Auxiliary battery negative (-) → Terminal 9 (MF)
Position between driving position (C) and retracted position (E) Moves from (D) to (E)
Auxiliary battery positive (+) → Terminal 9 (MF)
Auxiliary battery negative (-) → Terminal 3 (MR)
Position between driving position (C) and retracted position (E) Moves from (D) to (C)
Auxiliary battery positive (+) → Terminal 3 (MR)
Auxiliary battery negative (-) → Terminal 9 (MF)
Retracted position (E) Does not move
Auxiliary battery positive (+) → Terminal 9 (MF)
Auxiliary battery negative (-) → Terminal 3 (MR)
Retracted position (E) Moves from (E) to (C)


If the result is not as specified, replace the outer mirror retractor RH.



j.

Check the operation of the retractable mirror. (for 16 Pin Connector)

NOTICE:
·

Disconnect and reconnect the auxiliary battery between each mirror position check.

·

The mirror position cannot be changed manually when the auxiliary battery is connected. To change the mirror position manually, the auxiliary battery must be disconnected first.

·

If the motor is kept energized, even after each mirror position check, it may lead to a motor malfunction. Make sure to disconnect the auxiliary battery immediately after performing each mirror position check.



i.
B509871C03
1.573,3.729 1.573,2.979 1.573,2.979 1.875,2.979 true 1.573,3.958 1.573,4.375 1.573,4.375 1.896,4.375 true 1.958,0.313 2.271,0.469 0.313,0.156 10 false *a 2.344,1.115 2.656,1.271 0.313,0.156 10 false *b 2.188,2.063 2.5,2.219 0.313,0.156 10 false *c 1.802,2.313 2.115,2.469 0.313,0.156 10 false *d 1.354,2.479 1.667,2.635 0.313,0.156 10 false *e 0.802,3.156 1.115,3.313 0.313,0.156 10 false *f 1.927,2.896 2.24,3.052 0.313,0.156 10 false MR 1.958,4.292 2.271,4.448 0.313,0.156 10 false MF
*a (A) Forward Position
*b (B)
*c (C) Driving Position
*d (D)
*e (E) Retracted Position
*f Component without harness connected
(Outer Rear View Mirror Assembly RH)


Disconnect the outer rear view mirror assembly RH connector.


ii.

For each position: Disconnect the auxiliary battery, set the mirror position by hand, connect the auxiliary battery, and check the retractable mirror's movement.

OK:
Auxiliary Battery Connection Condition Specified Condition
Auxiliary battery positive (+) → Terminal 3 (MR)
Auxiliary battery negative (-) → Terminal 11 (MF)
Forward position (A) Moves from (A) to (E)
Auxiliary battery positive (+) → Terminal 11 (MF)
Auxiliary battery negative (-) → Terminal 3 (MR)
Forward position (A) Does not move
Auxiliary battery positive (+) → Terminal 3 (MR)
Auxiliary battery negative (-) → Terminal 11 (MF)
Position between forward position (A) and driving position (C) Moves from (B) to (E)
Auxiliary battery positive (+) → Terminal 11 (MF)
Auxiliary battery negative (-) → Terminal 3 (MR)
Position between forward position (A) and driving position (C) Moves from (B) to (A)
Auxiliary battery positive (+) → Terminal 3 (MR)
Auxiliary battery negative (-) → Terminal 11 (MF)
Driving position (C) Moves from (C) to (E)
Auxiliary battery positive (+) → Terminal 11 (MF)
Auxiliary battery negative (-) → Terminal 3 (MR)
Driving position (C) Does not move
Auxiliary battery positive (+) → Terminal 3 (MR)
Auxiliary battery negative (-) → Terminal 11 (MF)
Position between driving position (C) and retracted position (E) Moves from (D) to (E)
Auxiliary battery positive (+) → Terminal 11 (MF)
Auxiliary battery negative (-) → Terminal 3 (MR)
Position between driving position (C) and retracted position (E) Moves from (D) to (C)
Auxiliary battery positive (+) → Terminal 3 (MR)
Auxiliary battery negative (-) → Terminal 11 (MF)
Retracted position (E) Does not move
Auxiliary battery positive (+) → Terminal 11 (MF)
Auxiliary battery negative (-) → Terminal 3 (MR)
Retracted position (E) Moves from (E) to (C)


If the result is not as specified, replace the outer mirror retractor RH.



k.

Check the operation of the retractable mirror. (for 22 Pin Connector)

NOTICE:
·

Disconnect and reconnect the battery between each mirror position check.

·

The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.

·

If the motor is kept energized, even after each mirror position check, it may lead to a motor malfunction. Make sure to disconnect the battery immediately after performing each mirror position check.



i.
B495594C04
1.167,2.813 1.167,3.229 1.167,3.229 1.333,3.229 true 1.083,2.813 1.083,3.229 1.083,3.229 0.917,3.229 true 0.208,2.177 0.521,2.375 0.313,0.198 10 false *f 0.646,3.146 0.958,3.344 0.313,0.198 10 false MR 2.635,0.167 2.948,0.365 0.313,0.198 10 false *a 2.99,0.979 3.302,1.177 0.313,0.198 10 false *b 2.844,1.823 3.156,2.021 0.313,0.198 10 false *c 2.458,2.104 2.771,2.302 0.313,0.198 10 false *d 2.031,2.281 2.344,2.479 0.313,0.198 10 false *e 1.438,3.146 1.75,3.344 0.313,0.198 10 false MF
*a (A) Forward Position
*b (B)
*c (C) Driving Position
*d (D)
*e (E) Retracted Position
*f Component without harness connected
(Outer Rear View Mirror Assembly RH)


Disconnect the outer rear view mirror assembly RH connector.


ii.

For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror's movement.

OK:
Auxiliary Battery Connection Condition Specified Condition
Auxiliary battery positive (+) → Terminal 19 (MR)
Auxiliary battery negative (-) → Terminal 20 (MF)
Forward position (A) Moves from (A) to (E)
Auxiliary battery positive (+) → Terminal 20 (MF)
Auxiliary battery negative (-) → Terminal 19 (MR)
Forward position (A) Does not move
Auxiliary battery positive (+) → Terminal 19 (MR)
Auxiliary battery negative (-) → Terminal 20 (MF)
Position between forward position (A) and driving position (C) Moves from (B) to (E)
Auxiliary battery positive (+) → Terminal 20 (MF)
Auxiliary battery negative (-) → Terminal 19 (MR)
Position between forward position (A) and driving position (C) Moves from (B) to (A)
Auxiliary battery positive (+) → Terminal 19 (MR)
Auxiliary battery negative (-) → Terminal 20 (MF)
Driving position (C) Moves from (C) to (E)
Auxiliary battery positive (+) → Terminal 20 (MF)
Auxiliary battery negative (-) → Terminal 19 (MR)
Driving position (C) Does not move
Auxiliary battery positive (+) → Terminal 19 (MR)
Auxiliary battery negative (-) → Terminal 20 (MF)
Position between driving position (C) and retracted position (E) Moves from (D) to (E)
Auxiliary battery positive (+) → Terminal 20 (MF)
Auxiliary battery negative (-) → Terminal 19 (MR)
Position between driving position (C) and retracted position (E) Moves from (D) to (C)
Auxiliary battery positive (+) → Terminal 19 (MR)
Auxiliary battery negative (-) → Terminal 20 (MF)
Retracted position (E) Does not move
Auxiliary battery positive (+) → Terminal 20 (MF)
Auxiliary battery negative (-) → Terminal 19 (MR)
Retracted position (E) Moves from (E) to (C)


If the result is not as specified, replace the outer mirror retractor RH.



Hide 87940 2.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH

a.

Check the operation of the mirror surface. (for 7 Pin Connector)

NOTICE:

If the mirror surface is fully turned to the right, left, upward or downward position, the motor slips and produces a clicking noise. This is not a malfunction.


i.
B319941C15
0.958,2.354 0.958,1.969 0.958,1.969 1.146,1.969 true 0.865,2.365 0.865,1.573 0.865,1.573 1.156,1.573 true 0.76,2.385 0.76,1.885 0.76,1.885 0.531,1.885 true 0.219,2.125 0.823,2.5 0.604,0.375 10 false *a 0.271,1.813 0.75,2.104 0.479,0.292 10 false MV 1.219,1.49 1.708,1.771 0.49,0.281 10 false M+ 1.229,1.885 1.854,2.188 0.625,0.302 10 false MH
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


Disconnect the outer rear view mirror assembly LH connector.


ii.

Apply auxiliary battery voltage and check the operation of the mirror surface.

OK:
Auxiliary Battery Connection Specified Condition
Auxiliary battery positive (+) → Terminal 3 (MV)
Auxiliary battery negative (-) → Terminal 7 (M+)
Turns upward
Auxiliary battery positive (+) → Terminal 7 (M+)
Auxiliary battery negative (-) → Terminal 3 (MV)
Turns downward
Auxiliary battery positive (+) → Terminal 7 (M+)
Auxiliary battery negative (-) → Terminal 6 (MH)
Turns right
Auxiliary battery positive (+) → Terminal 6 (MH)
Auxiliary battery negative (-) → Terminal 7 (M+)
Turns left


If the result is not as specified, replace the outer rear view mirror assembly LH.



b.

Check the operation of the mirror surface. (for 11 Pin Connector)

NOTICE:

If the mirror surface is fully turned to the right, left, upward or downward position, the motor slips and produces a clicking noise. This is not a malfunction.


i.
B319980C20
1.49,2.521 1.49,1.844 1.49,1.844 1.75,1.844 true 1.385,2.521 1.385,1.615 1.385,1.615 1.167,1.615 true 1.281,2.521 1.281,1.896 1.281,1.896 1.063,1.896 true 1.802,1.76 2.125,1.969 0.323,0.208 10 false MV 0.948,1.542 1.229,1.729 0.281,0.188 10 false M+ 0.833,1.823 1.135,2.031 0.302,0.208 10 false MH 0.333,2.094 0.583,2.281 0.25,0.188 10 false *a
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


Disconnect the outer rear view mirror assembly LH connector.


ii.

Apply auxiliary battery voltage and check the operation of the mirror surface.

OK:
Auxiliary Battery Connection Specified Condition
Auxiliary battery positive (+) → Terminal 6 (MV)
Auxiliary battery negative (-) → Terminal 5 (M+)
Turns upward
Auxiliary battery positive (+) → Terminal 5 (M+)
Auxiliary battery negative (-) → Terminal 6 (MV)
Turns downward
Auxiliary battery positive (+) → Terminal 5 (M+)
Auxiliary battery negative (-) → Terminal 4 (MH)
Turns right
Auxiliary battery positive (+) → Terminal 4 (MH)
Auxiliary battery negative (-) → Terminal 5 (M+)
Turns left


If the result is not as specified, replace the outer rear view mirror assembly LH.



c.

Check the operation of the mirror surface. (for 16 Pin Connector)

NOTICE:

If the mirror surface is fully turned to the right, left, upward or downward position, the motor slips and produces a clicking noise. This is not a malfunction.


i.
B485588C04
1.563,1.844 1.271,1.844 1.271,1.844 1.271,2.552 true 0.979,3.229 1.271,3.229 1.271,3.229 1.271,2.792 true 1.667,3.229 1.406,3.229 1.406,3.229 1.406,2.792 true 0.698,1.969 1.01,2.167 0.313,0.198 10 false *a 1.604,1.771 1.917,1.969 0.313,0.198 10 false MV 0.74,3.146 1.052,3.344 0.313,0.198 10 false MH 1.698,3.135 2.01,3.333 0.313,0.198 10 false M+
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


Disconnect the outer rear view mirror assembly LH connector.


ii.

Apply auxiliary battery voltage and check the operation of the mirror surface.

OK:
Auxiliary Battery Connection Specified Condition
Auxiliary battery positive (+) → Terminal 1 (MV)
Auxiliary battery negative (-) → Terminal 10 (M+)
Turns upward
Auxiliary battery positive (+) → Terminal 10 (M+)
Auxiliary battery negative (-) → Terminal 1 (MV)
Turns downward
Auxiliary battery positive (+) → Terminal 10 (M+)
Auxiliary battery negative (-) → Terminal 9 (MH)
Turns right
Auxiliary battery positive (+) → Terminal 9 (MH)
Auxiliary battery negative (-) → Terminal 10 (M+)
Turns left


If the result is not as specified, replace the outer rear view mirror assembly LH.



d.

Check the operation of the mirror surface. (for 22 Pin Connector)

NOTICE:

If the mirror surface is fully turned to the right, left, upward or downward position, the motor slips and produces a clicking noise. This is not a malfunction.


i.
B495595C04
1.354,2.552 1.354,1.969 1.354,1.969 1.521,1.969 true 1.198,2.552 1.198,1.885 1.198,1.885 1.031,1.885 true 1.281,2.552 1.281,1.719 1.281,1.719 1.51,1.719 true 1.583,1.885 1.896,2.083 0.313,0.198 10 false MH 0.354,2.073 0.667,2.271 0.313,0.198 10 false *a 0.792,1.802 1.104,2 0.313,0.198 10 false MV 1.573,1.625 1.885,1.823 0.313,0.198 10 false M+
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


Disconnect the outer rear view mirror assembly LH connector.


ii.

Apply battery voltage and check the operation of the mirror surface.

OK:
Auxiliary Battery Connection Specified Condition
Auxiliary battery positive (+) → Terminal 7 (MV)
Auxiliary battery negative (-) → Terminal 8 (M+)
Turns upward
Auxiliary battery positive (+) → Terminal 8 (M+)
Auxiliary battery negative (-) → Terminal 7 (MV)
Turns downward
Auxiliary battery positive (+) → Terminal 8 (M+)
Auxiliary battery negative (-) → Terminal 9 (MH)
Turns right
Auxiliary battery positive (+) → Terminal 9 (MH)
Auxiliary battery negative (-) → Terminal 8 (M+)
Turns left


If the result is not as specified, replace the outer rear view mirror assembly LH.



e.

Check the operation of the mirror heater. (for 11 Pin Connector)

i.
B319984C26
0.854,2.563 0.854,1.969 0.854,1.969 1.094,1.969 true 1.417,2.833 1.417,3.219 1.417,3.219 1.656,3.219 true 1.729,3.135 1.875,3.313 0.146,0.177 10 false E 1.146,1.875 1.573,2.302 0.427,0.427 10 false + 0.313,2.188 0.604,2.396 0.292,0.208 10 false *a
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


Disconnect the outer rear view mirror assembly LH connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (+) - 11 (E) 25°C (77°F) 10 to 17 Ω


If the result is not as specified, replace the outer rear view mirror assembly LH.


iii.

Connect a cable from the positive (+) auxiliary battery terminal to terminal 2 (+) and the negative (-) auxiliary battery terminal to terminal 11 (E), then check that the mirror becomes warm.

HINT:

It takes a short time for the mirror to become warm.


OK:

Mirror becomes warm.


If the result is not as specified, replace the outer rear view mirror assembly LH.



f.

Check the operation of the mirror heater. (for 16 Pin Connector)

i.
B485589C04
2.031,2.573 2.031,1.813 2.031,1.813 2.448,1.813 true 2.031,2.813 2.031,3.229 2.031,3.229 2.469,3.229 true 0.792,1.948 1.104,2.146 0.313,0.198 10 false *a 2.5,1.74 2.813,1.938 0.313,0.198 10 false + 2.542,3.135 2.854,3.333 0.313,0.198 10 false -
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


Disconnect the outer rear view mirror assembly LH connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
7 (+) - 15 (-) 25°C (77°F) 10 to 17 Ω


If the result is not as specified, replace the outer rear view mirror assembly LH.


iii.

Connect a cable from the positive (+) battery terminal to terminal 7 and the negative (-) battery terminal to terminal 15, then check that the mirror becomes warm.

HINT:

It takes a short time for the mirror to become warm.


OK:

Mirror becomes warm.


If the result is not as specified, replace the outer rear view mirror assembly LH.



g.

Check the operation of the mirror heater. (for 22 Pin Connector)

i.
B495596C04
1.125,2.542 1.125,1.958 1.125,1.958 1.292,1.958 true 1.125,2.719 1.125,3.302 1.125,3.302 0.958,3.302 true 0.365,2.073 0.615,2.302 0.25,0.229 10 false *a 1.375,1.875 1.531,2.073 0.156,0.198 10 false + 0.854,3.198 1.01,3.396 0.156,0.198 10 false -
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


Disconnect the outer rear view mirror assembly LH connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6 (+) - 17 (-) 25°C (77°F) 10 to 17 Ω


If the result is not as specified, replace the outer rear view mirror assembly LH.


iii.

Connect a cable from the positive (+) battery terminal to terminal 6 (+) and the negative (-) battery terminal to terminal 17 (-), then check that the mirror becomes warm.

HINT:

It takes a short time for the mirror to become warm.


OK:

Mirror becomes warm.


If the result is not as specified, replace the outer rear view mirror assembly LH.



h.

Check the operation of the retractable mirror. (for 7 Pin Connector with Power Retract Mirror)

NOTICE:
·

Disconnect and reconnect the auxiliary battery between each mirror position check.

·

The mirror position cannot be changed manually when the auxiliary battery is connected. To change the mirror position manually, the auxiliary battery must be disconnected first.

·

If the motor is kept energized, even after each mirror position check, it may lead to a motor malfunction. Make sure to disconnect the auxiliary battery immediately after performing each mirror position check.



i.
B504674C04
1.969,3.302 2.135,3.302 2.135,3.302 2.135,2.719 true 2.396,3.302 2.229,3.302 2.229,3.302 2.229,2.719 true 0.635,0.104 0.948,0.302 0.313,0.198 10 false *a 0.313,0.875 0.625,1.073 0.313,0.198 10 false *b 0.469,1.792 0.781,1.99 0.313,0.198 10 false *c 0.885,2.01 1.198,2.208 0.313,0.198 10 false *d 1.26,2.229 1.573,2.427 0.313,0.198 10 false *e 1.781,2.115 2.094,2.313 0.313,0.198 10 false *f 1.75,3.208 2.063,3.406 0.313,0.198 10 false MF 2.438,3.208 2.75,3.406 0.313,0.198 10 false MR
*a (A) Forward Position
*b (B)
*c (C) Driving Position
*d (D)
*e (E) Retracted Position
*f Component without harness connected
(Outer Rear View Mirror Assembly LH)


Disconnect the outer rear view mirror assembly LH connector.


ii.

For each position: Disconnect the auxiliary battery, set the mirror position by hand, connect the auxiliary battery, and check the retractable mirror's movement.

OK:
Auxiliary Battery Connection Condition Specified Condition
Auxiliary battery positive (+) → Terminal 1 (MR)
Auxiliary battery negative (-) → Terminal 2 (MF)
Forward position (A) Moves from (A) to (E)
Auxiliary battery positive (+) → Terminal 2 (MF)
Auxiliary battery negative (-) → Terminal 1 (MR)
Forward position (A) Does not move
Auxiliary battery positive (+) → Terminal 1 (MR)
Auxiliary battery negative (-) → Terminal 2 (MF)
Position between forward position (A) and driving position (C) Moves from (B) to (E)
Auxiliary battery positive (+) → Terminal 2 (MF)
Auxiliary battery negative (-) → Terminal 1 (MR)
Position between forward position (A) and driving position (C) Moves from (B) to (A)
Auxiliary battery positive (+) → Terminal 1 (MR)
Auxiliary battery negative (-) → Terminal 2 (MF)
Driving position (C) Moves from (C) to (E)
Auxiliary battery positive (+) → Terminal 2 (MF)
Auxiliary battery negative (-) → Terminal 1 (MR)
Driving position (C) Does not move
Auxiliary battery positive (+) → Terminal 1 (MR)
Auxiliary battery negative (-) → Terminal 2 (MF)
Position between driving position (C) and retracted position (E) Moves from (D) to (E)
Auxiliary battery positive (+) → Terminal 2 (MF)
Auxiliary battery negative (-) → Terminal 1 (MR)
Position between driving position (C) and retracted position (E) Moves from (D) to (C)
Auxiliary battery positive (+) → Terminal 1 (MR)
Auxiliary battery negative (-) → Terminal 2 (MF)
Retracted position (E) Does not move
Auxiliary battery positive (+) → Terminal 2 (MF)
Auxiliary battery negative (-) → Terminal 1 (MR)
Retracted position (E) Moves from (E) to (C)


If the result is not as specified, replace the outer mirror retractor LH.



i.

Check the operation of the retractable mirror. (for 11 Pin Connector)

NOTICE:
·

Disconnect and reconnect the auxiliary battery between each mirror position check.

·

The mirror position cannot be changed manually when the auxiliary battery is connected. To change the mirror position manually, the auxiliary battery must be disconnected first.

·

If the motor is kept energized, even after each mirror position check, it may lead to a motor malfunction. Make sure to disconnect the auxiliary battery immediately after performing each mirror position check.



i.
B320733C27
2.156,2.74 2.156,3.104 2.156,3.104 1.958,3.104 true 2.156,2.521 2.156,2.021 2.156,2.021 2.323,2.021 true 0.625,0.094 0.802,0.25 0.177,0.156 10 false *a 0.333,0.854 0.51,1.01 0.177,0.156 10 false *b 0.49,1.75 0.667,1.906 0.177,0.156 10 false *c 0.865,2.01 1.042,2.167 0.177,0.156 10 false *d 1.25,2.219 1.427,2.375 0.177,0.156 10 false *e 2.385,1.938 2.698,2.188 0.313,0.25 10 false MR 1.74,3.021 2.021,3.25 0.281,0.229 10 false MF 1.698,2.115 1.969,2.365 0.271,0.25 10 false *f
*a (A) Forward Position
*b (B)
*c (C) Driving Position
*d (D)
*e (E) Retracted Position
*f Component without harness connected
(Outer Rear View Mirror Assembly LH)


Disconnect the outer rear view mirror assembly LH connector.


ii.

For each position: Disconnect the auxiliary battery, set the mirror position by hand, connect the auxiliary battery, and check the retractable mirror's movement.

OK:
Auxiliary Battery Connection Condition Specified Condition
Auxiliary battery positive (+) → Terminal 3 (MR)
Auxiliary battery negative (-) → Terminal 9 (MF)
Forward position (A) Moves from (A) to (E)
Auxiliary battery positive (+) → Terminal 9 (MF)
Auxiliary battery negative (-) → Terminal 3 (MR)
Forward position (A) Does not move
Auxiliary battery positive (+) → Terminal 3 (MR)
Auxiliary battery negative (-) → Terminal 9 (MF)
Position between forward position (A) and driving position (C) Moves from (B) to (E)
Auxiliary battery positive (+) → Terminal 9 (MF)
Auxiliary battery negative (-) → Terminal 3 (MR)
Position between forward position (A) and driving position (C) Moves from (B) to (A)
Auxiliary battery positive (+) → Terminal 3 (MR)
Auxiliary battery negative (-) → Terminal 9 (MF)
Driving position (C) Moves from (C) to (E)
Auxiliary battery positive (+) → Terminal 9 (MF)
Auxiliary battery negative (-) → Terminal 3 (MR)
Driving position (C) Does not move
Auxiliary battery positive (+) → Terminal 3 (MR)
Auxiliary battery negative (-) → Terminal 9 (MF)
Position between driving position (C) and retracted position (E) Moves from (D) to (E)
Auxiliary battery positive (+) → Terminal 9 (MF)
Auxiliary battery negative (-) → Terminal 3 (MR)
Position between driving position (C) and retracted position (E) Moves from (D) to (C)
Auxiliary battery positive (+) → Terminal 3 (MR)
Auxiliary battery negative (-) → Terminal 9 (MF)
Retracted position (E) Does not move
Auxiliary battery positive (+) → Terminal 9 (MF)
Auxiliary battery negative (-) → Terminal 3 (MR)
Retracted position (E) Moves from (E) to (C)


If the result is not as specified, replace the outer mirror retractor LH.



j.

Check the operation of the retractable mirror. (for 16 Pin Connector)

NOTICE:
·

Disconnect and reconnect the auxiliary battery between each mirror position check.

·

The mirror position cannot be changed manually when the auxiliary battery is connected. To change the mirror position manually, the auxiliary battery must be disconnected first.

·

If the motor is kept energized, even after each mirror position check, it may lead to a motor malfunction. Make sure to disconnect the auxiliary battery immediately after performing each mirror position check.



i.
B509872C03
1.573,3.781 1.573,3.031 1.573,3.031 1.896,3.031 true 1.573,4.021 1.573,4.354 1.573,4.354 1.885,4.354 true 1.323,0.333 1.635,0.49 0.313,0.156 10 false *a 1,1.073 1.313,1.229 0.313,0.156 10 false *b 1.177,1.99 1.49,2.146 0.313,0.156 10 false *c 1.583,2.25 1.896,2.406 0.313,0.156 10 false *d 1.958,2.458 2.271,2.615 0.313,0.156 10 false *e 0.844,3.177 1.156,3.333 0.313,0.156 10 false *f 1.938,2.958 2.25,3.115 0.313,0.156 10 false MR 1.927,4.271 2.24,4.427 0.313,0.156 10 false MF
*a (A) Forward Position
*b (B)
*c (C) Driving Position
*d (D)
*e (E) Retracted Position
*f Component without harness connected
(Outer Rear View Mirror Assembly LH)


Disconnect the outer rear view mirror assembly LH connector.


ii.

For each position: Disconnect the auxiliary battery, set the mirror position by hand, connect the auxiliary battery, and check the retractable mirror's movement.

OK:
Auxiliary Battery Connection Condition Specified Condition
Auxiliary battery positive (+) → Terminal 3 (MR)
Auxiliary battery negative (-) → Terminal 11 (MF)
Forward position (A) Moves from (A) to (E)
Auxiliary battery positive (+) → Terminal 11 (MF)
Auxiliary battery negative (-) → Terminal 3 (MR)
Forward position (A) Does not move
Auxiliary battery positive (+) → Terminal 3 (MR)
Auxiliary battery negative (-) → Terminal 11 (MF)
Position between forward position (A) and driving position (C) Moves from (B) to (E)
Auxiliary battery positive (+) → Terminal 11 (MF)
Auxiliary battery negative (-) → Terminal 3 (MR)
Position between forward position (A) and driving position (C) Moves from (B) to (A)
Auxiliary battery positive (+) → Terminal 3 (MR)
Auxiliary battery negative (-) → Terminal 11 (MF)
Driving position (C) Moves from (C) to (E)
Auxiliary battery positive (+) → Terminal 11 (MF)
Auxiliary battery negative (-) → Terminal 3 (MR)
Driving position (C) Does not move
Auxiliary battery positive (+) → Terminal 3 (MR)
Auxiliary battery negative (-) → Terminal 11 (MF)
Position between driving position (C) and retracted position (E) Moves from (D) to (E)
Auxiliary battery positive (+) → Terminal 11 (MF)
Auxiliary battery negative (-) → Terminal 3 (MR)
Position between driving position (C) and retracted position (E) Moves from (D) to (C)
Auxiliary battery positive (+) → Terminal 3 (MR)
Auxiliary battery negative (-) → Terminal 11 (MF)
Retracted position (E) Does not move
Auxiliary battery positive (+) → Terminal 11 (MF)
Auxiliary battery negative (-) → Terminal 3 (MR)
Retracted position (E) Moves from (E) to (C)


If the result is not as specified, replace the outer mirror retractor LH.



k.

Check the operation of the retractable mirror. (for 22 Pin Connector)

NOTICE:
·

Disconnect and reconnect the battery between each mirror position check.

·

The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.

·

If the motor is kept energized, even after each mirror position check, it may lead to a motor malfunction. Make sure to disconnect the battery immediately after performing each mirror position check.



i.
B495597C04
2.729,2.813 2.729,3.229 2.729,3.229 2.896,3.229 true 2.656,2.813 2.656,3.229 2.656,3.229 2.49,3.229 true 2.99,3.146 3.302,3.344 0.313,0.198 10 false MF 2.24,3.146 2.552,3.344 0.313,0.198 10 false MR 1.813,2.188 2.125,2.385 0.313,0.198 10 false *f 0.646,0.177 0.958,0.375 0.313,0.198 10 false *a 0.354,0.885 0.667,1.083 0.313,0.198 10 false *b 0.5,1.802 0.813,2 0.313,0.198 10 false *c 0.854,2.083 1.167,2.281 0.313,0.198 10 false *d 1.24,2.281 1.552,2.479 0.313,0.198 10 false *e
*a (A) Forward Position
*b (B)
*c (C) Driving Position
*d (D)
*e (E) Retracted Position
*f Component without harness connected
(Outer Rear View Mirror Assembly LH)


Disconnect the outer rear view mirror assembly LH connector.


ii.

For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror's movement.

OK:
Auxiliary Battery Connection Condition Specified Condition
Battery positive (+) → Terminal 19 (MR)
Battery negative (-) → Terminal 20 (MF)
Forward position (A) Moves from (A) to (E)
Battery positive (+) → Terminal 20 (MF)
Battery negative (-) → Terminal 19 (MR)
Forward position (A) Does not move
Battery positive (+) → Terminal 19 (MR)
Battery negative (-) → Terminal 20 (MF)
Position between forward position (A) and driving position (C) Moves from (B) to (E)
Battery positive (+) → Terminal 20 (MF)
Battery negative (-) → Terminal 19 (MR)
Position between forward position (A) and driving position (C) Moves from (B) to (A)
Battery positive (+) → Terminal 19 (MR)
Battery negative (-) → Terminal 20 (MF)
Driving position (C) Moves from (C) to (E)
Battery positive (+) → Terminal 20 (MF)
Battery negative (-) → Terminal 19 (MR)
Driving position (C) Does not move
Battery positive (+) → Terminal 19 (MR)
Battery negative (-) → Terminal 20 (MF)
Position between driving position (C) and retracted position (E) Moves from (D) to (E)
Battery positive (+) → Terminal 20 (MF)
Battery negative (-) → Terminal 19 (MR)
Position between driving position (C) and retracted position (E) Moves from (D) to (C)
Battery positive (+) → Terminal 19 (MR)
Battery negative (-) → Terminal 20 (MF)
Retracted position (E) Does not move
Battery positive (+) → Terminal 20 (MF)
Battery negative (-) → Terminal 19 (MR)
Retracted position (E) Moves from (E) to (C)


If the result is not as specified, replace the outer mirror retractor LH.