Home › Vehicle Exterior › MIRROR (EXT) › OUTER REAR VIEW MIRROR › from 2021.02
RM33C0E _59 Vehicle Exterior _065470 MIRROR (EXT) _0332579 OUTER REAR VIEW MIRROR A

MIRROR (EXT)  OUTER REAR VIEW MIRROR  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 87966 1.INSTALL OUTER MIRROR RETRACTOR (w/ Power Retract Mirror)

a.
B483097E01
0.677,0.823 0.917,1.083 0.24,0.26 10 false 1 2.313,1.458 2.521,1.677 0.208,0.219 10 false 2

Install the 2 screws in the order shown in the illustration.


b.
B483098

Install a new frame sub-assembly to the housing with the 2 screws.


c.
B483096C01
0,0 0,0 false
V113147

Install in this Direction


Pass a new wire harness sub-assembly through the frame sub-assembly as shown in the illustration.


d.
B483094

Connect the connector.


e.
B483093

Engage the 2 clamps.


f.

Connect the connector.


g.
B483092

Install the actuator sub-assembly with the 3 screws.


h.

Pass the wire harness sub-assembly through the base sub-assembly.


i.
B483091

Using a T25 "TORX" socket wrench, install the base sub-assembly with 3 new screws.

NOTICE:

When installing the base sub-assembly, check that the wire harness sub-assembly is not caught between the base sub-assembly and body. Failure to do so may cause a short circuit.



j.
B483090

Engage the guide and 8 claws to install a new lower cover.


k.
B485150

Pass the wire harness sub-assembly through a new gasket sub-assembly and engage the 8 guides to install the gasket sub-assembly.

NOTICE:

Make sure there is no clearance between the gasket sub-assembly and base sub-assembly.



l.
B485151C01
1.354,2.99 1.667,3.146 0.313,0.156 10 false *a
*a Marking
V113147

Install in this Direction


Adjust the wire harness sub-assembly so that the marking is at the position shown in the illustration.


m.
B485152C02
1.396,1.698 1.552,1.896 0.156,0.198 10 false A

Wind vinyl tape around the wire harness sub-assembly to secure it.

Reference Measurement
Area Measurement
A 40 mm (1.57 in.)


n.
B485149C02
1.667,1.917 1.833,1.771 true 2.177,1.448 2.479,1.156 true 1.521,1.917 1.833,2.073 0.313,0.156 10 false *a 2.49,1.021 2.802,1.177 0.313,0.156 10 false *b
*a Clamp
*b Guide


Engage the guide.


o.

Install the bracket with the screw.


p.

Engage the clamp.


q.

for 7, 11 Pin Connector:

i.
B483100

Connect each connector to a new adapter.


ii.
B483101C01
1,2.583 1.5,2.583 false 0.802,2.469 1.115,2.625 0.313,0.156 10 false *a
*a Wire Harness Routing


Route the longer part of the wire harness sub-assembly as shown in the illustration.



r.

for 16 Pin Connector:

i.

Set the retainer of a new connector housing to the unlock position.

B534392C11
2.135,1.354 2.365,2.01 2.365,2.01 2.083,1.531 false 6.021,2.031 6.198,1.688 false 1.49,2.104 1.49,1.833 false 0.656,2.073 0.833,1.729 false 0.563,2.083 0.875,2.281 0.313,0.198 10 false *b 2.313,2.01 2.625,2.208 0.313,0.198 10 false *c 3.5,0.667 3.813,0.865 0.313,0.198 10 false *d 5.927,2.01 6.24,2.208 0.313,0.198 10 false *e 1.406,2.083 1.719,2.281 0.313,0.198 10 false *a
*a Connector Housing *b Retainer Unlock Position
*c Wire Harness Pin *d Back View of Wire Harness Connector
*e Retainer Lock Position - -



ii.

Insert new wire harness pins from the backside of the adapter until they lock.

Wire Harness Color Chart:
1 2 3 4 5 6 7 8
PURPLE - SKY BLUE - ORANGE WHITE-BLACK BLACK-GREEN BLACK-RED
9 10 11 12 13 14 15 16
BROWN RED LIGHT GREEN - YELLOW-BLACK GRAY WHITE PINK



iii.

Set the retainer to the lock position.

NOTICE:
·

When inserting the wire harness pins, compare with the connector that was cut off during removal to verify the insertion positions, and then make sure to insert the pins of the correct wire colors in the correct positions.

·

Make sure that the wire harness pins are securely locked in position and cannot be removed.

·

The wire harness pins cannot be removed after they have locked into place, so be absolutely certain to insert them in the correct positions.




iv.
B589086

Route the longer part of the wire harness assembly as shown in the illustration.



s.

for 22 Pin Connector:

i.

Set the retainer of a new connector housing to the unlock position.

B606959C02
2.073,1.365 2.302,2.115 2.302,2.115 1.99,1.552 true 1.438,2.208 1.438,1.896 false 5.948,2.156 6.104,1.781 false 0.49,2.229 0.646,1.854 false 0.385,2.24 0.698,2.438 0.313,0.198 10 false *b 2.24,2.135 2.552,2.333 0.313,0.198 10 false *c 3.427,0.844 3.74,1.042 0.313,0.198 10 false *d 5.833,2.156 6.146,2.354 0.313,0.198 10 false *e 1.333,2.198 1.646,2.396 0.313,0.198 10 false *a
*a Connector Housing *b Retainer Unlock Position
*c Wire Harness Pin *d Back View of Wire Harness Connector
*e Retainer Lock Position - -



ii.

Insert new wire harness pins from the backside of the adapter until they lock.

Wire Harness Color Chart:
1 2 3 4 5 6 7 8
YELLOW GREEN - PINK - BLACK-GREEN PURPLE RED
9 10 11 12 13 14 15 16
BROWN ORANGE YELLOW-BLACK BLACK BLUE - BLACK-RED -
17 18 19 20 21 22 - -
WHITE - SKY BLUE LIGHT GREEN GRAY WHITE-BLACK - -



iii.

Set the retainer to the lock position.

NOTICE:
·

When inserting the wire harness pins, compare with the connector that was cut off during removal to verify the insertion positions, and then make sure to insert the pins of the correct wire colors in the correct positions.

·

Make sure that the wire harness pins are securely locked in position and cannot be removed.

·

The wire harness pins cannot be removed after they have locked into place, so be absolutely certain to insert them in the correct positions.




iv.
B589086

Route the longer part of the wire harness assembly as shown in the illustration.



t.
B394558C04
1.083,0.729 1.083,0.313 false 2.094,1.844 2.25,2.042 0.156,0.198 10 false A 1.01,1.844 1.167,2.042 0.156,0.198 10 false B 0.99,0.135 1.302,0.333 0.313,0.198 10 false *a
*a Vinyl Tape


Wind vinyl tape around the wire harness sub-assembly to secure it.

Reference Measurement
Area Measurement
A 0 to 5.0 mm (0 to 0.1969 in.)
B 50 mm (1.97 in.)


u.
B483104C02
1.333,1.667 1.333,1.25 false 2.021,0.26 2.198,0.438 0.177,0.177 10 false A 1.281,1.667 1.594,1.865 0.313,0.198 10 false *a
*a Vinyl Tape


Wind vinyl tape around the clamp to secure it.

Reference Measurement
Area Measurement
A 185 mm (7.28 in.)


Hide 81740 2.INSTALL SIDE TURN SIGNAL LIGHT ASSEMBLY

Hide 87945C 3.INSTALL OUTER MIRROR LOWER COVER (w/ Panoramic View Monitor System)

a.

Engage the 3 guides and 2 claws to install the outer mirror lower cover.


Hide 4.INSTALL NO. 2 OUTER MIRROR COVER

a.
B469072C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 2 guides and 2 claws to install the No. 2 outer mirror cover as shown in the illustration.


Hide 5.INSTALL OUTER MIRROR HOLE COVER ASSEMBLY (w/o Panoramic View Monitor System)

Hide 86790F 6.INSTALL SIDE TELEVISION CAMERA ASSEMBLY (w/ Panoramic View Monitor System)

Hide 7.INSTALL OUTER MIRROR HOLE COVER WITH SIDE TELEVISION CAMERA ASSEMBLY (w/ Panoramic View Monitor System)