DATA LIST
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / Circumference Monitoring Camera Control Module / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| RHD/LHD Data Check | Status of the RHD/LHD data check | OK/NG | OK: Parking assist ECU is normal
NG: Parking assist ECU is abnormal |
- |
| HV/EV/ENG Data Check | Verification of the HV/ENG data | OK/NG | OK: Data verification normal
NG: Data verification abnormal |
- |
| 2WD/4WD Data Check | Verification of 2WD/4WD data | OK/NG | OK: Data verification normal
NG: Data verification abnormal |
- |
| Destination Data Check | Verification of destination data | OK/NG | OK: Data verification normal
NG: Data verification abnormal |
- |
| AT/MT Data Check | Verification of AT/MT data | OK/NG | OK: Data verification normal
NG: Data verification abnormal |
- |
| Main CPU Forced Termination Detection Record | A history item indicating that the main CPU did not enter standby status within 15 seconds of turning the ignition switch off and a forced end was applied | Unrec/Rec | Unrec: Television camera controller is normal
Rec: Television camera controller is abnormal |
- |
| Main CPU Abnormal Response Record | A history item indicating that the main CPU became unresponsive in normal status | Unrec/Rec | Unrec: Television camera controller is normal
Rec: Television camera controller is abnormal |
- |
| Main CPU Abnormal Reset Record | A history item indicating that the main CPU was reset, although the ignition switch was not turned off in normal status | Unrec/Rec | Unrec: Television camera controller is normal
Rec: Television camera controller is abnormal |
- |
| Image Processing IC Written Protect Record | A history item indicating that the image processing IC memory was write protected | Unrec/Rec | Unrec: Television camera controller is normal
Rec: Television camera controller is abnormal |
- |
| Image Processing IC Initialized Malfunction Record | A history item indicating that the image processing IC memory was not initialized | Unrec/Rec | Unrec: Television camera controller is normal
Rec: Television camera controller is abnormal |
- |
| Main EEPROM Access Status | Main EEPROM access status | OK/NG | OK: Television camera controller is normal
NG: Television camera controller is abnormal |
- |
| Sub EEPROM Access Status | Sub-EEPROM access status | OK/NG | OK: Television camera controller is normal
NG: Television camera controller is abnormal |
- |
| System Power Supply Voltage Malfunction Record | A history item indicating an abnormally generated-voltage value from the system power source | Unrec/Rec | Unrec: Television camera controller is normal
Rec: Television camera controller is abnormal |
- |
| Main CPU Starting Malfunction Record | A history item indicating that the main CPU did not start | Unrec/Rec | Unrec: Television camera controller is normal
Rec: Television camera controller is abnormal |
- |
| CAN CPU Boot Malfunction Record | A history item indicating that the CPU controlling the input and output of the information obtained via the CAN communication system did not start and the information could not be retrieved | Unrec/Rec | Unrec: Television camera controller is normal
Rec: Television camera controller is abnormal |
- |
| Visual Display Line Status | Displays the status of the video signals displayed on the multi-display | OK/NG | OK: GVIF cable is normal
NG: GVIF cable is abnormal |
- |
| Wheel Speed Sensor (4wheel) | Reception state of the vehicle speed signal from the skid control ECU | OK/NG | OK: Speed signal received
NG: Speed signal not received |
- |
| Continuous Bus Off | Continuous bus off status (Global) | Not Detected/Detected | Not detected: Communication condition available
Detected: Communication condition not available |
- |
| Sending CAN Message | Communication condition from television camera controller (Global) | OK/NG | OK: Communication condition available
NG: Communication condition not available |
- |
| Camera Changing SW Signal Status | Signal status at the BLSW terminal (switch camera signal) | ON/OFF | ON: Panoramic view monitor main switch on
OFF: Panoramic view monitor main switch off |
- |
| Back Camera Availability Consistency | Status of ECU stored in rear television camera assembly | OK/NG | OK: Normal
NG: Rear television camera assembly or television camera controller is abnormal |
- |
| Image Adjustment Status | Status of the image adjustment status | Incomplete/Processing/Complete | Incomplete: Image adjustment incomplete
Processing: Image adjustment in processing Complete: Image adjustment completed |
- |
| Number of DTC | Number of DTCs (past and present) | Min: 0, Max: 255 | Number of DTCs will be displayed | - |