Home › Vehicle Interior › SEAT › POWER SEAT TRACK RAIL ASSEMBLY › from 2021.02
RM33C0E _58 Vehicle Interior _065462 SEAT _0436955 POWER SEAT TRACK RAIL ASSEMBLY A

SEAT  POWER SEAT TRACK RAIL ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during upper seat track rail sub-assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative auxiliary battery terminal Perform steering sensor zero point calibration Lane tracing assist system (Click here)
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
·

Position control ECU assembly (driver seat)

·

Slide motor (upper seat track rail sub-assembly (driver seat))


Initialize position control ECU Front power seat control system (Click here)

CAUTION:
·

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION

·

Wear protective gloves. Sharp areas on the parts may injure your hands.



HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The following procedure is for LHD vehicles.



PROCEDURE

Hide 89710C 2.REMOVE POSITION CONTROL ECU ASSEMBLY (w/ Seat Position Memory System)

Hide 71868N 3.REMOVE FRONT SEAT FRONT CUSHION SHIELD

Hide 71812D 4.REMOVE FRONT SEAT CUSHION SHIELD (w/ Vertical Adjuster)

Hide 71811D 5.REMOVE FRONT SEAT CUSHION SHIELD (w/o Vertical Adjuster)

Hide 72108 6.REMOVE UPPER SEAT TRACK RAIL SUB-ASSEMBLY (w/ Vertical Adjuster)

NOTICE:
·
B586592C01
2.438,2.667 2.656,2.854 0.219,0.188 10 false *a
*a 80 mm (3.15 in.)


In order to reduce the risk of damage to the part and to ensure ease of operations, secure a space of 80 mm (3.15 in.) or more as shown in the illustration.

·

Secure enough space to ensure that the upper seat track rail sub-assembly does not contact any other objects during installation.



a.
B586593

Disconnect the slide motor connector.


b.

Disengage the claw and 2 clamps.


c.
B586594

Remove the 2 screws.


d.
B586595C01
0,0 0,0 false
V113147

Remove in this direction
V100155

Protective Tape


Using a screwdriver with its tip wrapped with protective tape, disengage the 2 claws.


e.

Disengage the guide to remove the front seat cushion wire harness holder as shown in the illustration.

NOTICE:

When remove the front seat cushion wire harness holder, take care not to damage each connector and wire harness.



f.
B586596C01
0,0 0,0 false
V113147

Remove in this direction
V100155

Protective Tape


Using a screwdriver with its tip wrapped with protective tape, disengage the claw.


g.

Disengage the guide to remove the front seat lower cushion shield LH from the upper seat track rail sub-assembly as shown in the illustration.


h.
B586597C01
2.167,0.646 2.781,0.479 true 2.448,1.625 3.063,1.542 true 2.833,0.385 3.031,0.583 0.198,0.198 10 false *a 3.094,1.469 3.281,1.656 0.188,0.188 10 false *b
*a Clamp
*b Guide
V113147

Remove in this direction
V100155

Protective Tape


Using a screwdriver with its tip wrapped with protective tape, disengage the claw.


i.

Disengage the clamp.


j.

Disengage the guide to remove the front seat lower cushion shield RH from the upper seat track rail sub-assembly as shown in the illustration.


k.
B586598C01
0,0 0,0 false
V113147

Remove in this direction
V100155

Protective Tape


Using a screwdriver with its tip wrapped with protective tape, disengage the claw.


l.

Disengage the guide to remove the front seat lower cushion shield from the upper seat track rail sub-assembly as shown in the illustration.


m.
B586599

Disengage the clamp.


n.

Remove the 8 nuts and upper seat track rail sub-assembly.

NOTICE:

Do not reuse the upper seat track rail sub-assembly.



Hide 72106B 7.REMOVE UPPER SEAT TRACK RAIL SUB-ASSEMBLY (w/o Vertical Adjuster)

NOTICE:
·
B586604C01
2.344,2.667 2.563,2.854 0.219,0.188 10 false *a
*a 80 mm (3.15 in.)


In order to reduce the risk of damage to the part and to ensure ease of operations, secure a space of 80 mm (3.15 in.) or more as shown in the illustration.

·

Secure enough space to ensure that the upper seat track rail sub-assembly does not contact any other objects during installation.



a.
B586605

Disconnect the slide motor connector.


b.
B586606

Remove the 5 nuts and upper seat track rail sub-assembly.

NOTICE:

Do not reuse the upper seat track rail sub-assembly.