Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE ACTUATOR(for RHD) › from 2021.02
RM33C0E _54 Brake _065442 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0319338 BRAKE ACTUATOR(for RHD) A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE ACTUATOR(for RHD)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during brake actuator assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane Tracing Assist System (Click here)
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Replacement of brake actuator assembly
1.

Bleed air

2.

Clear the data stored during previous linear solenoid valve offset learning, ABS holding solenoid valve learning, brake pedal stroke sensor assembly zero point calibration and system information memorization.

3.

Perform linear solenoid valve offset learning, ABS holding solenoid valve learning, brake pedal stroke sensor assembly zero point calibration and system information memorization.


·

DTCs are stored

·

ABS warning light illuminates

·

Brake warning light / yellow (minor malfunction) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)for Initialization
(Click here)for Calibration
Operate the electric parking brake switch Electric Parking Brake System (Click here)

CAUTION / NOTICE / HINT

NOTICE:

While the auxiliary battery is connected, even if the power switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.


PROCEDURE

Hide 47070 1.REMOVE BRAKE BOOSTER PUMP ASSEMBLY

Hide 44510 2.REMOVE BRAKE ACTUATOR ASSEMBLY

a.
C377981

Remove the 3 bolts and brake actuator assembly from the brake actuator bracket assembly.

NOTICE:
·

Do not hold the brake actuator assembly by the connector.

·

Do not drop the brake actuator assembly when carrying it.




Hide 44546A 3.REMOVE BRAKE ACTUATOR BOLT CUSHION

a.
C377982C02
1.625,0.552 1.927,0.552 false 2.646,1.594 2.948,1.594 false 2.25,1.76 2.25,1.896 2.25,1.896 2.49,1.896 false 1.594,0.208 1.896,0.208 false 0.51,0.677 0.75,0.677 0.75,0.677 0.75,0.469 false 0.74,0.104 1.063,0.104 1.063,0.104 1.063,0.281 false 0.594,0.042 0.906,0.198 0.313,0.156 10 false *1 0.354,0.604 0.667,0.76 0.313,0.156 10 false *2 1.927,0.135 2.24,0.292 0.313,0.156 10 false *1 2.969,1.51 3.281,1.667 0.313,0.156 10 false *1 1.958,0.479 2.271,0.635 0.313,0.156 10 false *2 2.521,1.823 2.833,1.979 0.313,0.156 10 false *2
*1 Brake Actuator Case Collar
*2 Brake Actuator Bolt Cushion


Remove the 3 brake actuator case collars from the brake actuator bolt cushions.


b.

Remove the 3 brake actuator bolt cushions from the brake actuator bracket assembly.