Home › Suspension › FRONT SUSPENSION › FRONT LOWER BALL JOINT › from 2021.02
RM33C0E _53 Suspension _065438 FRONT SUSPENSION _0334230 FRONT LOWER BALL JOINT A

FRONT SUSPENSION  FRONT LOWER BALL JOINT  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front lower ball joint assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane Tracing Assist System (Click here)
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Front wheel alignment adjustment
1.

Clear zero point calibration data.

2.

Perform yaw rate and acceleration sensor zero point calibration.


·

DTCs are stored

·

ABS warning light illuminates

·

Brake warning light / yellow (minor malfunction) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)

NOTICE:

After the power switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.


HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1.REMOVE FRONT AXLE ASSEMBLY

Hide 43340A 2.REMOVE FRONT LOWER BALL JOINT ASSEMBLY

a.
C370106

Secure the front axle assembly in a vise using aluminum plates.

NOTICE:

Do not overtighten the vise.



b.
C370107

Remove the cotter pin.


c.

Remove the nut.


d.
C370108C01
0.896,0.094 1.292,0.094 1.292,0.094 1.292,1.063 true 1.156,0.094 1.156,1.063 true 3.042,0.927 3.354,1.083 0.313,0.156 10 false *a 0.594,0.021 1.052,0.219 0.458,0.198 10 false SST
*a 1 mm (0.0394 in.)


Install SST to the front lower ball joint assembly as shown in the illustration.

SST
09960-20010  (09961-02050)

NOTICE:

Check that the clearance measurement between SST and the front axle assembly is 1 mm (0.0394 in.).



e.
C370109C01
1.469,1.344 1.885,1.344 false 0.896,4.354 0.99,4.354 0.99,4.354 1.198,3.99 false 2.406,2.698 2.802,2.031 2.802,2.031 2.896,2.031 true 1.615,1.771 2.219,1.771 false 0.74,4.271 1.052,4.427 0.313,0.156 10 false *a 2.313,0.76 2.625,0.917 0.313,0.156 10 false *b 1.313,1.26 1.625,1.417 0.313,0.156 10 false *c 2.938,1.948 3.25,2.104 0.313,0.156 10 false *d 2.313,0.385 2.625,0.542 0.313,0.156 10 false *b 2.083,3.729 2.396,3.885 0.313,0.156 10 false B 2.083,3.448 2.396,3.604 0.313,0.156 10 false A 2.26,1.688 2.719,1.885 0.458,0.198 10 false SST
*a Center Nut
*b Molybdenum Grease Application Area
*c Place wrench here
*d String
V113147

Turn


Using SST, remove the front lower ball joint assembly from the front axle assembly as shown in the illustration.

SST
09960-20010  (09961-02010, 09961-02050)

CAUTION:

Apply molybdenum grease to the threads and end of the SST bolt.


NOTICE:
·

Be sure to tighten the string firmly to secure SST to the front axle assembly to prevent SST from falling off.

·

Install SST with the center nut so that (A) and (B) shown in the illustration are parallel. Otherwise, the front lower ball joint dust cover may be damaged.

·

Be sure to place a wrench on the part shown in the illustration.

·

Do not damage the front lower ball joint dust cover.

·

Do not damage the steering knuckle.

·

Do not damage the front disc brake dust cover.