Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › REAR AIRBAG SENSOR › from 2021.02
RM33C0E _58 Vehicle Interior _065460 SUPPLEMENTAL RESTRAINT SYSTEMS _0331871 REAR AIRBAG SENSOR A

SUPPLEMENTAL RESTRAINT SYSTEMS  REAR AIRBAG SENSOR  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during side No. 2 airbag sensor removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative auxiliary battery terminal Perform steering sensor zero point calibration Lane tracing assist system (Click here)
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

CAUTION:
B394719

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 64718C 2.REMOVE LUGGAGE TRIM SERVICE HOLE COVER

Hide 3.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Click hereGeneral>MAINTENANCE>AUXILIARY BATTERY>REMOVAL

CAUTION:
B422343

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 73350C 4.DISCONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY

Hide 5.REMOVE REAR SEAT CUSHION ASSEMBLY

Hide 72693 6.REMOVE REAR SEAT CUSHION LOCK HOOK

Hide 71940A 7.REMOVE REAR SEAT HEADREST ASSEMBLY (for Reclining Seat Type)

Hide 72996A 8.REMOVE REAR SEATBACK COVER (for Reclining Seat Type)

Hide 9.REMOVE REAR SEATBACK ASSEMBLY (for Reclining Seat Type)

Hide 62332A 10.DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP

HINT:

Disconnect the rear door opening trim weatherstrip to the extent that allows the removal of the rear side seatback assembly.


Hide 11.REMOVE REAR SIDE SEATBACK ASSEMBLY

Hide 89831B 12.REMOVE SIDE NO. 2 AIRBAG SENSOR

a.

Check that the power switch is off.


b.

Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:
B422343

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Disconnect the connector from the side No. 2 airbag sensor.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.


i.

Push down the white housing lock and slide the yellow CPA. (At this time, the connector cannot be disconnected yet.)

B474824C01
0.521,0.615 0.813,0.615 0.813,0.615 1.073,1.021 true 0.438,0.906 0.729,0.906 0.729,0.906 0.927,1.156 true 3,0.917 3.292,0.917 3.292,0.917 3.49,1.167 true 1.385,1.969 1.385,1.313 false 3.052,0.646 3.344,0.646 3.344,0.646 3.615,1.031 true 3.917,1.969 3.917,1.313 false 1.313,2 1.625,2.156 0.313,0.156 10 false *b 0.375,0.51 0.688,0.667 0.313,0.156 10 false *a 2.885,0.552 3.198,0.708 0.313,0.156 10 false *a 3.854,1.99 4.167,2.146 0.313,0.156 10 false *b 0.323,0.823 0.635,0.979 0.313,0.156 10 false A 2.875,0.833 3.188,0.99 0.313,0.156 10 false A
*a White Housing Lock *b Yellow CPA
V113147

Push in this Direction
V113148

Slide in this Direction



ii.

Push down the white housing lock again and disconnect the connector.

NOTICE:

Do not push down the part (A) shown in the illustration when disconnecting the connector.




d.
B468742

Remove the bolt and disengage the claw to remove the side No. 2 airbag sensor.


e.

Check that the position of the white housing lock is as shown in the illustration.

B296256C01
5.01,0.51 5.302,0.781 0.292,0.271 10 *b 1.792,0.51 2.083,0.802 0.292,0.292 10 *a
*a Correct *b Incorrect