Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › FRONT DOOR BELT MOULDING › from 2021.02
RM33C0E _59 Vehicle Exterior _065474 EXTERIOR PANELS / TRIM _0333720 FRONT DOOR BELT MOULDING A

EXTERIOR PANELS / TRIM  FRONT DOOR BELT MOULDING  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front door belt moulding removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function When Necessary Procedures are not Performed Link
Disconnect cable from negative auxiliary battery terminal Perform steering sensor zero point calibration Lane Tracing Assist System (Click here)
Pre-collision System
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic View Monitor System (Click here)
·

Front door glass sub-assembly

·

Front door glass run

·

Front door belt moulding


Initialize power window control system
·

Auto up and down function

·

Jam protection function

·

Remote control function

·

Key-linked function

·

Wireless transmitter-linked function

·

Key-off operation function

·

Catch protection function

·

Window open warning function


(Click here)

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 64718C 2.REMOVE LUGGAGE TRIM SERVICE HOLE COVER

Hide 3.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 67492A 4.REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH

Hide 74038A 5.REMOVE FRONT DOOR ARMREST COVER SUB-ASSEMBLY

Hide 6.REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Driver Side)

Hide 7.REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Front Passenger Side)

Hide 74220 8.REMOVE FRONT ARMREST ASSEMBLY

Hide 81230 9.REMOVE COURTESY LIGHT ASSEMBLY

Hide 67602 10.REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY

Hide 11.REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP WITH FRONT DOOR VENT SEAL

Hide 67832 12.REMOVE FRONT DOOR SERVICE HOLE COVER

Hide 68102 13.REMOVE FRONT DOOR GLASS SUB-ASSEMBLY

Hide 75720 14.REMOVE FRONT DOOR BELT MOULDING ASSEMBLY

a.
B469794C01
0,0 0,0 false
V100155

Protective Tape


Apply protective tape around the front door belt moulding assembly as shown in the illustration.


b.
B573294C01
1.427,1.115 0.51,1.115 true 0.313,1.021 0.625,1.219 0.313,0.198 10 false *a
*a Claw
V113147

Rotate in this Direction


Disengage the 5 claws as shown in the illustration.


c.
B573295C01
2.958,1.333 2.958,0.865 true 2.885,1.354 3.198,1.552 0.313,0.198 10 false *a
*a Thin-bladed Screwdriver with its Tip Wrapped with Protective Tape
V113147

Push in this Direction


Using a thin-bladed screwdriver with its tip wrapped with protective tape, disengage the claw as shown in the illustration.


d.

Slightly twist and hold the front door belt moulding assembly in the direction indicated by the arrow (1) shown in the illustration.

B573296C01
0,0 0,0 false
V113147

Twist in this Direction (1)
V113148

Slide in this Direction (2)


NOTICE:

If the front door belt moulding assembly is pulled upwards, the claw may break and fall inside the door panel.



e.

Slide the front door belt moulding assembly in the direction indicated by the arrow (2) shown in the illustration to disengage the claw and remove the front door belt moulding assembly.