Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function) › from 2021.08
RM33C0E _58 Vehicle Interior _065456 THEFT DETERRENT / KEYLESS ENTRY _0389661 ENTRY AND START SYSTEM(for Start Function) U

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  TERMINALS OF ECU  


CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


B416786N54
2,0.333 2.417,0.583 0.417,0.25 3.25,0.333 3.667,0.583 0.417,0.25 4.583,0.333 5,0.583 0.417,0.25 2.073,0.365 2.385,0.563 0.313,0.198 10 false A13 3.365,0.365 3.677,0.563 0.313,0.198 10 false R8 4.656,0.365 4.969,0.563 0.313,0.198 10 false K62

a.

Disconnect the R8 and K62 certification ECU (smart key ECU assembly) connectors.


b.

Measure the resistance and voltage according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Tester Connection Wiring Color Input / Output Terminal Description Condition Specified Condition Related Data List Item/DTC
R8-25 (STP1) - Body ground BE - Body ground Input Stop light switch signal Brake pedal depressed → Brake pedal released 9 V or higher → 1 V or less Stop Light Switch1
K62-4 (+B) - K62-18 (E) W - W-B Input Power source Power switch off 11 to 14 V -
K62-22 (P) - K62-18 (E) R - W-B Input P position signal Shift lever in P → Shift lever not in P 30 kΩ or higher → Below 200 Ω Shift P Signal
K62-15 (CUTB) - Body ground R - Body ground Input Dark current cut pin* Power switch off 11 to 14 V -
K62-18 (E) - Body ground W-B - Body ground - GND Always Below 1 Ω -
K62-21 (SSW2) - Body ground L - Body ground Input SSW2 contact signal
HINT:

Backup for SSW1. Behaves the same way as SSW1.


Power switch pushed → Power switch not pushed Below 15 Ω → 10 kΩ or higher Start Switch2
K62-23 (SSW1) - Body ground GR - Body ground Input SSW1 contact signal Power switch pushed → Power switch not pushed Below 15 Ω → 10 kΩ or higher Start Switch1
K62-19 (SPD) - Body ground R - Body ground Input Vehicle speed signal Always 30 kΩ or higher Vehicle Speed Signal

*: In order to prevent the vehicle auxiliary battery from being depleted when the vehicle is shipped long distances, a fuse that cuts unnecessary electrical load while the vehicle is being shipped is installed in the circuit. If the fuse is removed, the circuit becomes open. If the fuse that is between the vehicle auxiliary battery and terminal CUTB is removed and the circuit is open, the certification ECU (smart key ECU assembly) changes to a certain control mode (example: the transmission of radio waves every 0.25 seconds, which form the detection area, stops).



c.

Connect the R8 and K62 certification ECU (smart key ECU assembly) connectors.


d.

Measure the voltage and resistance, and check for pulses according to the value(s) in the table below.

Tester Connection Wiring Color Input / Output Terminal Description Condition Specified Condition Related Data List Item/DTC
K62-14 (SLP) - K62-18 (E) BE - W-B Input Steering lock position signal Steering locked → Steering unlocked 11 to 14 V → 1.5 V or less Steering Unlock Switch
K62-25 (SLR+) - K62-18 (E) W - W-B Output Steering lock motor operation command signal
(Steering lock motor operation permission signal sent from the certification ECU (smart key ECU assembly))
When a door is opened, the steering lock motor will be operated if all of the following conditions are met:
·

The steering is unlocked.

·

The power switch is off.

·

The shift lever is in P.


Pulse generation
(See waveform 1)
-
K62-13 (LIN) - K62-18 (E) B - W-B*1
G - W-B*2
Input / Output LIN communication line Power switch on (IG) Pulse generation Steering Lock Start Cond
K62-3 (IGB) - K62-18 (E) GR - W-B Output IGB signal Power switch off → Power switch on (IG) 1 V or less → 8.5 V or higher -
K62-22 (P) - K62-18 (E) R - W-B Input P position signal Shift lever in P → Shift lever not in P 9 V or higher → 2.76 V or less Shift P Signal
K62-21 (SSW2) - K62-18 (E) L - W-B Input SSW2 contact signal
HINT:

Backup for SSW1. Behaves the same way as SSW1.


Power switch not pushed → Power switch pushed 9 V or higher → 1 V or less Start Switch2
K62-23 (SSW1) - K62-18 (E) GR - W-B Input SSW1 contact signal Power switch not pushed → Power switch pushed 9 V or higher → 1 V or less Start Switch1
K62-16 (ACCD) - K62-18 (E) LG - W-B Output ACC signal Power switch off → Power switch on (ACC) 1 V or less → 8.5 V or higher ACC Relay Monitor
K62-17 (IG1D) - K62-18 (E) R - W-B Output IG signal Power switch on (ACC) → Power switch on (IG) 1 V or less → 9 V or higher IG Relay Monitor (Outside)
K62-19 (SPD) - K62-18 (E) R - W-B Input Vehicle speed signal Vehicle being driven at approx. 5 km/h (3 mph) Pulse generation
(See waveform 2)
Vehicle Speed Signal
K62-27 (ST2) - K62-18 (E) L - W-B Output STSW signal With the brake pedal depressed, the power switch is pressed and held → After approx. 3 sec. has elapsed, the power switch is released 8.5 V or higher → 1 V or less -
K62-8 (CLG5) - K62-18 (E) B - W-B Output Output to No. 1 indoor electrical key antenna assembly (front floor) Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Within 30 seconds of closing any door


Pulse generation
(See waveform 3)
-
K62-9 (CG5B) - K62-18 (E) LG - W-B Output Output to No. 1 indoor electrical key antenna assembly (front floor) (terminal on opposite side of component from CLG5 output terminal) Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Within 30 seconds of closing any door


Pulse generation
(See waveform 3)
-
R8-5 (CLG6) - K62-18 (E) W - W-B Output Output to No. 1 indoor electrical key antenna assembly (rear floor) Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Within 30 seconds of closing any door


Pulse generation
(See waveform 3)
-
R8-6 (CG6B) - K62-18 (E) R - W-B Output Output to No. 1 indoor electrical key antenna assembly (rear floor) (terminal on opposite side of component from CLG6 output terminal) Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Within 30 seconds of closing any door


Pulse generation
(See waveform 3)
-
K62-5 (TXCT) - K62-11 (AGND) GR - BE Output Signal output to transponder key amplifier Power switch off, brake pedal not depressed, 30 seconds or more after driver door opened and then closed Below 1 V
·

BCC Malfunction

·

Abnormal Status

·

Different Encrypt Code

·

Different Serial Number

·

Frame Error

·

Response


K62-6 (CODE) - K62-11 (AGND) B - BE Input Signal input from transponder key amplifier Power switch off, brake pedal not depressed, 30 seconds or more after driver door opened and then closed Below 1 V
K62-7 (VC5) - K62-11 (AGND) BE - BE Output Transponder key amplifier power supply Power switch off, brake pedal not depressed, 30 seconds or more after driver door opened and then closed Below 1 V
K62-11 (AGND) - Body ground BE - Body ground - Transponder key amplifier ground Always Below 1 Ω
K62-5 (TXCT) - K62-11 (AGND) GR - BE Output Signal output to transponder key amplifier
(Code sent from certification ECU (smart key ECU assembly) to transponder key amplifier built into power switch, and then transmitted by transponder key amplifier antenna as radio waves)
Power switch off, electrical key transmitter sub-assembly not in cabin, within 30 seconds of power switch pressed Pulse generation
(See waveform 4)
·

BCC Malfunction

·

Abnormal Status

·

Different Encrypt Code

·

Different Serial Number

·

Frame Error

·

Response


K62-6 (CODE) - K62-11 (AGND) B - BE Input Signal input from transponder key amplifier
(Radio waves from transponder key amplifier built into power switch used to detect key information. Key information then sent to certification ECU (smart key ECU assembly))
Power switch off, power switch pressed with electrical key transmitter sub-assembly held near power switch
HINT:

Remove the transmitter battery before performing this inspection.


Pulse generation
(See waveform 5)
K62-7 (VC5) - K62-11 (AGND) BE - BE Output Transponder key amplifier power supply
(Power supplied from certification ECU (smart key ECU assembly) when transponder key amplifier built into power switch activated)
Power switch off, electrical key transmitter sub-assembly not in cabin, within 30 seconds of power switch pressed Pulse generation
(See waveform 6)
A13-3 (EFII) - K62-18 (E)*1 V - W-B Input EFI communication input
(Signal input from hybrid vehicle control ECU assembly to certification ECU (smart key ECU assembly))
Power switch off 11 to 14 V
·

EFI Code Receive

·

Engine Start Request


A13-4 (EFIO) - K62-18 (E)*1 GR - W-B Output EFI communication output
(Signal output from certification ECU (smart key ECU assembly) to hybrid vehicle control ECU assembly)
Power switch off 11 to 14 V → 1 V or less
A13-3 (EFII) - K62-18 (E)*1 V - W-B Input EFI communication input
(Signal input from hybrid vehicle control ECU assembly to certification ECU (smart key ECU assembly))
Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after cable disconnected and reconnected to auxiliary battery Pulse generation
(See waveform 7)
A13-4 (EFIO) - K62-18 (E)*1 GR - W-B Output EFI communication output
(Signal output from certification ECU (smart key ECU assembly) to hybrid vehicle control ECU assembly)
Power switch turned on (IG) using registered electrical key transmitter sub-assembly Pulse generation
(See waveform 8)
K62-20 (IND) - K62-18 (E) W - W-B Output Security indicator output Power switch off → on (IG) Pulse generation → Below 2 V -
R8-7 (WCSW) - K62-18 (E)*3 LG - W-B Output Wireless charger system stop signal Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly inside vehicle

3.

Power switch off → on (ACC)


Below 1 V → 4.5 to 6 V
(For 1 second after power switch on (ACC))
-

*1: w/o ID Code Box

*2: w/ ID Code Box

*3: w/ Wireless Charging System


HINT:
·

The waveform of the steering lock actuator motor stopped can be checked without performing any particular operation.

·

The waveform of the steering lock actuator motor operating can be checked if either of the following operations is performed:

-

To unlock the steering, bring the electrical key transmitter sub-assembly into the cabin and turn the power switch on (ACC) or on (IG).

-

To lock the steering, open a door with the power switch off and the shift lever in P.





e.

Using an oscilloscope, check the waveform of the ECU.

NOTICE:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.
C221561C62
0.229,0.406 1.635,0.573 1.406,0.167 1.469,1.573 2.438,1.698 0.969,0.125 2.281,0.469 2.708,0.625 0.427,0.156 1.938,1.698 2.021,1.979 2.021,1.979 2.073,1.979 false 1.646,0.438 2.76,0.198 2.76,0.198 2.833,0.198 false 2.75,0.208 2.552,0.458 false 2.917,1.563 3.292,1.708 0.375,0.146 10 false GND 2.125,1.896 2.615,2.042 0.49,0.146 10 false *b 2.865,0.125 3.229,0.354 0.365,0.229 10 false *a
*a Steering lock motor not operating
*b Steering lock motor operating


Waveform 1

Measurement Condition
Item Content
Tester Connection K62-25 (SLR+) - K62-18 (E)
Tool Setting 2 V/DIV., 200 ms./DIV.
Condition When a door is opened, the steering lock motor will be operated if all of the following conditions are met:
·

The steering is unlocked.

·

The power switch is off.

·

The shift lever is in P.




ii.
B220145N21
2.875,1.177 3.229,1.344 0.354,0.167 10 false GND

Waveform 2

Measurement Condition
Item Content
Tester Connection K62-19 (SPD) - K62-18 (E)
Tool Setting 5 V/DIV., 20 ms./DIV.
Condition Vehicle being driven at approx. 5 km/h (3 mph)

HINT:

The wavelength becomes shorter as the vehicle speed increases.



iii.
B340874C02
0.188,1.042 0.646,1.24 0.458,0.198 10 false GND 1.01,1.917 1.469,2.115 0.458,0.198 10 false *a 2.135,1.938 2.594,2.135 0.458,0.198 10 false *b
*a For 30 seconds after any door closed
*b After 30 seconds or more have elapsed since any door closed


Waveform 3

Measurement Condition
Item Content
Tester Connection K62-8 (CLG5) - K62-18 (E)
K62-9 (CG5B) - K62-18 (E)
R8-5 (CLG6) - K62-18 (E)
R8-6 (CG6B) - K62-18 (E)
Tool Setting 2 V/DIV., 500 ms/DIV.
Condition Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Within 30 seconds of closing any door




iv.
B051052N19
2.802,0.781 3.156,0.969 0.354,0.188 10 GND

Waveform 4

Measurement Condition
Item Content
Tester Connection K62-5 (TXCT) - K62-11 (AGND)
Tool Setting 2 V/DIV., 20 ms./DIV.
Condition Power switch off, electrical key transmitter sub-assembly not in cabin, within 30 seconds of power switch pressed


v.
B368716C01
0.104,0.135 0.417,0.292 0.313,0.156 10 false *a 0.094,1.896 0.406,2.052 0.313,0.156 10 false *b 3.031,1.219 3.427,1.49 0.396,0.271 10 false GND 3.031,2.948 3.427,3.219 0.396,0.271 10 false GND
*a Waveform
*b Waveform (detail)


Waveform 5

Measurement Condition
Item Content
Tester Connection K62-6 (CODE) - K62-11 (AGND)
Tool Setting
·

Waveform

1 V/DIV., 20 ms./DIV.

·

Waveform (detail)

2 V/DIV., 100 μs./DIV.


Condition Power switch off, power switch pressed with electrical key transmitter sub-assembly held near power switch*

HINT:

*: Remove the transmitter battery before performing this inspection.



vi.
B216007N06
2.885,1.031 3.427,1.375 0.542,0.344 10 GND

Waveform 6

Measurement Condition
Item Content
Tester Connection K62-7 (VC5) - K62-11 (AGND)
Tool Setting 2 V/DIV., 200 ms./DIV.
Condition Power switch off, electrical key transmitter sub-assembly not in cabin, within 30 seconds of power switch pressed


vii.

Waveform 7

B325134C03
0.917,1.271 1.375,1.469 0.458,0.198 10 GND 2.719,1.354 3.177,1.552 0.458,0.198 10 *a 2.906,1.354 3.365,1.552 0.458,0.198 10 *b
*a Approximately 160 ms. *b Approximately 270 ms.


Measurement Condition
Item Content
Tester Connection A13-3 (EFII) - K62-18 (E)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after cable disconnected and reconnected to auxiliary battery


viii.

Waveform 8

B333259C02
0.844,1.24 1.302,1.438 0.458,0.198 10 GND 3.115,1.323 3.344,1.531 0.229,0.208 10 *a 3.313,1.323 3.542,1.531 0.229,0.208 10 *b
*a Approximately 160 ms. *b Approximately 270 ms.


Measurement Condition
Item Content
Tester Connection A13-4 (EFIO) - K62-18 (E)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Power switch turned on (IG) using registered electrical key transmitter sub-assembly




CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)


B438339N02
3.417,0.333 3.833,0.583 0.417,0.25 3.49,0.385 3.802,0.583 0.313,0.198 10 false K65

a.

Disconnect the K65 steering lock ECU (steering lock actuator or upper bracket assembly) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Input / Output Terminal Description Condition Specified Condition Related Data List Item/DTC
K65-1 (GND) - Body ground W-B - Body ground - Ground Always Below 1 Ω -
K65-6 (IG2) - K65-1 (GND) LG - W-B Input IG signal (IG2 power supply input for steering lock motor) Power switch off Below 1 V -
Power switch on (IG) 11 to 14 V
K65-7 (B) - Body ground W - Body ground Input Constant power supply Power switch off 11 to 14 V -


c.

Connect the K65 steering lock ECU (steering lock actuator or upper bracket assembly) connector.


d.

Measure the voltage, and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Input / Output Terminal Description Condition Specified Condition Related Data List Item/DTC
K65-3 (IGE) - K65-1 (GND) W - W-B Input Steering lock motor operation permission signal (motor operation permission signal supplied by certification ECU (smart key ECU assembly)) Steering lock motor operating when all conditions met, and then door opened:
·

Shift lever in P

·

Steering unlocked

·

Power switch turned off


Pulse generation
(See waveform 1)
·

Power Supply Short

·

Unlock Request Receive

·

Lock Request Receive


K65-4 (SLP1) - K65-1 (GND) BE - W-B Output Steering lock bar position signal (signal output from steering unlock sensor) Steering locked → unlocked 11 to 14 V → Below 1.5 V Sensor Value
K65-5 (LIN) - K65-1 (GND) B - W-B*1
V - W-B*2
Input / Output LIN communication line Power switch on (IG) Pulse generation Steering Lock Start Cond

*1: w/o ID Code Box

*2: w/ ID Code Box


HINT:
·

There is 1 motor and 2 sensors built into the steering lock actuator or upper bracket assembly.

·

When taking measurements when the lock motor is stopped, it is not necessary to perform any operations.

·

In order to take measurements when the lock motor is operating, perform either of the following operations:

-

To unlock the steering, carry the key and turn the power switch on (ACC) or on (IG).

-

To lock the steering, turn the power switch off with the shift lever in P, and then open a door.





e.

Using an oscilloscope, check the waveform.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.
C259594C03
1.052,0.344 2.958,0.219 2.958,0.219 2.521,0.396 true 2.031,1.802 2.292,1.969 true 3.01,0.135 3.323,0.292 0.313,0.156 10 *a 2.344,1.938 2.667,2.104 0.323,0.167 10 *b 2.938,1.594 3.302,1.792 0.365,0.198 10 GND
*a Steering lock motor not operating
*b Steering lock motor operating


Waveform 1 (Reference)

Measurement Condition
Item Content
Tester Connection K65-3 (IGE) - K65-1 (GND)
Tool Setting 2 V/DIV., 200 ms./DIV.
Condition Steering lock motor operating when all conditions met, and then door opened:
·

Shift lever in P

·

Steering unlocked

·

Power switch turned off






CHECK ID CODE BOX (IMMOBILISER CODE ECU) (w/ ID Code Box)


B463193N25
3.344,0.146 3.792,0.417 0.448,0.271 3.406,0.188 4.021,0.385 0.615,0.198 10 false K159

a.

Disconnect the K159 ID code box (immobiliser code ECU) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Tester Connection Wiring Color Input/Output Terminal Description Condition Specified Condition Related Data List Item
K159-1 (+B) - Body ground LA-GR - Body ground Input Power source Power switch off 11 to 14 V -
K159-5 (GND) - Body ground W-B - Body ground - Ground Always Below 1 Ω


c.

Reconnect the K159 ID code box (immobiliser code ECU) connector.


d.

Measure the voltage and check for pulses according to the value(s) in the table below.

Tester Connection Wiring Color Input/Output Terminal Description Condition Specified Condition Related Data List Item
K159-3 (EFII) - K159-5 (GND) LG - W-B Input EFI communication input
(Signal input from hybrid vehicle control ECU assembly to ID code box (immobiliser code ECU))
Power switch off 11 to 14 V Entry&Start
·

EFI Code Receive

·

Engine Start Request


K159-3 (EFII) - K159-5 (GND) LG - W-B Input EFI communication input
(Signal input from hybrid vehicle control ECU assembly to ID code box (immobiliser code ECU))
Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after cable disconnected and reconnected to auxiliary battery Pulse generation
(See waveform 1)
K159-4 (EFIO) - K159-5 (GND) L - W-B Output EFI communication output
(Signal output from ID code box (immobiliser code ECU) to hybrid vehicle control ECU assembly)
Power switch off Below 1 V
K159-4 (EFIO) - K159-5 (GND) L - W-B Output EFI communication output
(Signal output from ID code box (immobiliser code ECU) to hybrid vehicle control ECU assembly)
Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after cable disconnected and reconnected to auxiliary battery Pulse generation
(See waveform 2)
K159-2 (LIN1) - K159-5 (GND) GR - W-B Input/Output LIN communication line Power switch on (IG) Pulse generation Entry&Start
·

Steering Lock Start Cond




e.

Using an oscilloscope, check the waveform.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.

Waveform 1

B325134C03
0.917,1.271 1.375,1.469 0.458,0.198 10 GND 2.719,1.354 3.177,1.552 0.458,0.198 10 *a 2.906,1.354 3.365,1.552 0.458,0.198 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Item Content
Tester Connection K159-3 (EFII) - K159-5 (GND)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after cable disconnected and reconnected to auxiliary battery


ii.

Waveform 2

B333259C02
0.844,1.24 1.302,1.438 0.458,0.198 10 GND 3.115,1.323 3.344,1.531 0.229,0.208 10 *a 3.313,1.323 3.542,1.531 0.229,0.208 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Item Content
Tester Connection K159-4 (EFIO) - K159-5 (GND)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after cable disconnected and reconnected to auxiliary battery




CHECK HYBRID VEHICLE CONTROL ECU ASSEMBLY


B220221N57
1.479,0.135 1.865,0.365 0.385,0.229 2.833,0.146 3.219,0.375 0.385,0.229 4.302,0.146 4.688,0.375 0.385,0.229 5.531,0.167 5.917,0.396 0.385,0.229 1.563,0.177 2.208,0.531 0.646,0.354 10 false A28 2.917,0.188 3.385,0.479 0.469,0.292 10 false A29 4.385,0.188 4.865,0.448 0.479,0.26 10 false K69 5.615,0.208 6.083,0.427 0.469,0.219 10 false K70

a.

Measure the voltage and resistance, and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Input / Output Terminal Description Condition Specified Condition Related Data List Item/DTC
A28-3 (IG2) - K69-6 (E1) B - W-B Input Ignition power supply Power switch on (IG) 11 to 14 V -
K69-6 (E1) - Body ground W-B - Body ground - Ground Always Below 1 Ω -
K70-23 (IMO) - K69-6 (E1) BE - W-B*1*3, *4
LG - W-B*2*3
Output EFI communication output
(Signal output from hybrid vehicle control ECU assembly to certification ECU (smart key ECU assembly))*1
(Signal output from hybrid vehicle control ECU assembly to ID code box (immobiliser code ECU))*2
Power switch off 11 to 14 V
·

EFI Code Receive

·

Engine Start Request


K70-23 (IMO) - K69-6 (E1) BE - W-B*1*3, *4
LG - W-B*2*3
Output EFI communication output
(Signal output from hybrid vehicle control ECU assembly to certification ECU (smart key ECU assembly))*1
(Signal output from hybrid vehicle control ECU assembly to ID code box (immobiliser code ECU))*2
Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after cable disconnected and reconnected to auxiliary battery Pulse generation
(See waveform 1)
K70-22 (IMI) - K69-6 (E1) G - W-B*1*3, *4
L - W-B*2*3
Input EFI communication input
(Signal input from certification ECU (smart key ECU assembly) to hybrid vehicle control ECU assembly)*1
(Signal input from ID code box (immobiliser code ECU) to hybrid vehicle control ECU assembly)*2
Power switch off 11 to 14 V → 1 V or less
K70-22 (IMI) - K69-6 (E1) G - W-B*1*3, *4
L - W-B*2*3
Input EFI communication input
(Signal input from certification ECU (smart key ECU assembly) to hybrid vehicle control ECU assembly)*1
(Signal input from ID code box (immobiliser code ECU) to hybrid vehicle control ECU assembly)*2
Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after cable disconnected and reconnected to auxiliary battery Pulse generation
(See waveform 2)

*1: w/o ID Code Box

*2: w/ ID Code Box

*3: for Nickel Metal Hydride Battery

*4: for Lithium-ion Battery



b.

Using an oscilloscope, check the waveform.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.

Waveform 1 (Reference)

B325134C22
0.896,1.24 1.354,1.438 0.458,0.198 10 false GND 2.719,1.354 3.177,1.552 0.458,0.198 10 false *a 2.906,1.354 3.365,1.552 0.458,0.198 10 false *b
*a Approximately 160 ms. *b Approximately 270 ms.


Measurement Condition
Item Content
Tester Connection K70-23 (IMO) - K69-6 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after cable disconnected and reconnected to auxiliary battery


ii.

Waveform 2 (Reference)

B333259C02
0.844,1.24 1.302,1.438 0.458,0.198 10 GND 3.115,1.323 3.344,1.531 0.229,0.208 10 *a 3.313,1.323 3.542,1.531 0.229,0.208 10 *b
*a Approximately 160 ms. *b Approximately 270 ms.


Measurement Condition
Item Content
Tester Connection K70-22 (IMI) - K69-6 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after cable disconnected and reconnected to auxiliary battery




CHECK POWER SWITCH


B271001N82
3.333,0.25 3.75,0.5 0.417,0.25 3.406,0.292 3.833,0.469 0.427,0.177 10 false K63

a.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Input / Output Terminal Description Condition Specified Condition Related Data List Item/DTC
K63-6 (AGND) - Body ground BE - Body ground - Transponder key amplifier ground Always Below 1 Ω -
K63-7 (TXCT) - K63-6 (AGND) GR - BE Input Immobiliser communication input Power switch off, brake pedal not depressed, 30 seconds or more after driver door opened and then closed Below 1 V -
K63-8 (CODE) - K63-6 (AGND) B - BE Output Immobiliser communication output Power switch off, brake pedal not depressed, 30 seconds or more after driver door opened and then closed Below 1 V -
K63-10 (VC5) - K63-6 (AGND) BE - BE Input Transponder key amplifier power supply Power switch off, brake pedal not depressed, 30 seconds or more after driver door opened and then closed Below 1 V -


b.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Input / Output Terminal Description Condition Specified Condition Related Data List Item/DTC
K63-7 (TXCT) - K63-6 (AGND) GR - BE Input Signal input from certification ECU (smart key ECU assembly)
(Code sent from certification ECU (smart key ECU assembly) to transponder key amplifier built into power switch, and then transmitted by transponder key amplifier antenna as radio waves)
Power switch off, electrical key transmitter sub-assembly not in cabin, within 30 seconds of power switch pressed Pulse generation
(See waveform 1)
·

BCC Malfunction

·

Abnormal Status

·

Different Encrypt Code

·

Different Serial Number

·

Frame Error

·

Response

HINT:

If immobiliser key code verification communication is not performed correctly, the malfunction may be indicated by one or more of the Data List items listed above



K63-8 (CODE) - K63-6 (AGND) B - BE Output Signal output to certification ECU (smart key ECU assembly)
(Radio waves from transponder key amplifier built into power switch used to detect key information. Key information then sent to certification ECU (smart key ECU assembly))
Power switch off, power switch pressed with electrical key transmitter sub-assembly held near power switch* Pulse generation
(See waveform 2)
K63-10 (VC5) - K63-6 (AGND) BE - BE Input Transponder key amplifier power supply
(Power supplied from certification ECU (smart key ECU assembly) when transponder key amplifier built into power switch activated)
Power switch off, electrical key transmitter sub-assembly not in cabin, within 30 seconds of power switch pressed Pulse generation
(See waveform 3)

HINT:

*: Remove the transmitter battery before performing this inspection.



c.

Using an oscilloscope, check the waveform.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.
B051052N18
2.802,0.781 3.156,0.969 0.354,0.188 10 GND

Waveform 1 (Reference)

Measurement Condition
Item Content
Tester Connection K63-7 (TXCT) - K63-6 (AGND)
Tool Setting 2 V/DIV., 20 ms./DIV.
Condition Power switch off, electrical key transmitter sub-assembly not in cabin, within 30 seconds of power switch pressed


ii.
B368716C01
0.104,0.135 0.417,0.292 0.313,0.156 10 false *a 0.094,1.896 0.406,2.052 0.313,0.156 10 false *b 3.031,1.219 3.427,1.49 0.396,0.271 10 false GND 3.031,2.948 3.427,3.219 0.396,0.271 10 false GND
*a Waveform
*b Waveform (detail)


Waveform 2 (Reference)

Measurement Condition
Item Content
Tester Connection K63-8 (CODE) - K63-6 (AGND)
Tool Setting
·

Waveform

1 V/DIV., 20 ms./DIV.

·

Waveform (detail)

2 V/DIV., 100 μs./DIV.


Condition Power switch off, power switch pressed with electrical key transmitter sub-assembly held near power switch*

HINT:

*: Remove the transmitter battery before performing this inspection.



iii.
B216007N05
2.885,1.031 3.427,1.375 0.542,0.344 10 GND

Waveform 3 (Reference)

Measurement Condition
Item Content
Tester Connection K63-10 (VC5) - K63-6 (AGND)
Tool Setting 2 V/DIV., 200 ms./DIV.
Condition Power switch off, electrical key transmitter sub-assembly not in cabin, within 30 seconds of power switch pressed