Home › Engine / Hybrid System › A25A-FXS (ENGINE CONTROL) › SFI SYSTEM (w/ Canister Pump Module) › from 2022.01
RM33C0E _51 Engine / Hybrid System _065419 A25A-FXS ENGINE CONTROL _0332275 SFI SYSTEM(w/ Canister Pump Module) C

A25A-FXS ENGINE CONTROL  SFI SYSTEM(w/ Canister Pump Module)  P040000  Exhaust Gas Recirculation "A" Flow  P04019C  Exhaust Gas Recirculation "A" Low / Insufficient Flow  P04029B  Exhaust Gas Recirculation "A" High/Excessive Flow  


DESCRIPTION

Based on the driving conditions, the ECM regulates the volume of exhaust gas that is recirculated to each engine cylinder in order to lower the combustion temperature and reduce NOx emissions. The ECM monitors signals such as engine speed, engine coolant temperature, electric load, and vehicle speed. When the EGR permission conditions are met, the ECM controls the opening of the EGR valve linearly through signals to the EGR step motor.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P040000 Exhaust Gas Recirculation "A" Flow During fuel cut, when the change in intake manifold pressure when the EGR valve assembly is operating and when not operating is insufficient (2 trip detection logic).
·

EGR valve assembly

·

EGR passage

·

EGR cooler assembly

·

Intake system

·

Manifold absolute pressure sensor


Comes on DTC stored SAE Code: P0400
P04019C Exhaust Gas Recirculation "A" Low / Insufficient Flow
·

During fuel cut, when the change in intake manifold pressure when the EGR valve assembly is operating and when not operating is insufficient, the intake manifold pressure is less than 41.5 kPa (6.02 psi) when the EGR valve assembly is not operating (1 trip detection logic) (except Brazil OBD Phase 3).

·

Charge in intake manifold pressure is small when the EGR valve opened and closed during fuel cut operation (2 trip detection logic) (for Brazil OBD Phase 3).


·

EGR valve assembly

·

EGR passage

·

EGR cooler assembly

·

Manifold absolute pressure sensor


Comes on DTC stored SAE Code: P0401
P04029B Exhaust Gas Recirculation "A" High/Excessive Flow During fuel cut, when the change in intake manifold pressure when the EGR valve assembly is operating and not operating is insufficient, the intake manifold pressure is 41.5 kPa (6.02 psi) or more when the EGR valve assembly is not operating (1 trip detection logic).
·

EGR valve assembly

·

EGR passage

·

Intake system

·

Manifold absolute pressure sensor


Comes on DTC stored SAE Code: P0402

HINT:

DTC P04019C or DTC P04029B will only be stored when DTC P040000 is stored in the second trip.


MONITOR DESCRIPTION

except Brazil OBD Phase 3
·

P040000

During fuel cut (vehicle being driven with idle ON), when the change in intake manifold pressure when the EGR valve assembly is operating and not operating is insufficient, the ECM determines that the EGR valve is stuck and stores DTC P040000 and illuminates the MIL.

·

P04019C

During fuel cut (vehicle being driven with idle ON), when the change in intake manifold pressure when the EGR valve assembly is operating and not operating is insufficient, the intake manifold pressure is less than the threshold when the EGR valve assembly is not operating, the ECM determines that the flow through the EGR valve is hindered and stores DTC P04019C and illuminates the MIL.

·

P04029B

During fuel cut (vehicle being driven with idle ON), when the change in intake manifold pressure when the EGR valve assembly is operating and not operating is insufficient, the intake manifold pressure is more than the threshold when the EGR valve assembly is not operating, the ECM determines that the flow through the EGR valve is excessive and stores DTC P04029B and illuminates the MIL.



for Brazil OBD Phase 3

The ECM monitors the pressure inside the intake manifold while opening and closing the EGR valve during fuel cut operation. If there is no change in the manifold absolute pressure sensor value, the ECM interprets this as a malfunction of the EGR valve assembly, illuminates the MIL and stores this DTC.


MONITOR STRATEGY

except Brazil OBD Phase 3
Required Sensors/Components (Main) EGR valve assembly
Manifold absolute pressure sensor
Required Sensors/Components (Related) Crankshaft position sensor
Camshaft position sensor
Vehicle speed sensor
Engine coolant temperature sensor
Mass air flow meter sub-assembly
Frequency of Operation Once per driving cycle

for Brazil OBD Phase 3
Required Sensors/Components (Main) EGR valve assembly
Manifold absolute pressure sensor
Required Sensors/Components (Related) Engine coolant temperature sensor
Frequency of Operation Once per driving cycle

TYPICAL ENABLING CONDITIONS

except Brazil OBD Phase 3
Engine speed 950 to 1600 rpm
Vehicle speed 21 km/h (13 mph) or more
Intake air temperature -10°C (14°F) or higher

for Brazil OBD Phase 3
Engine speed 950 to 1600 rpm
Vehicle speed 20 km/h (13 mph) or more
Intake air temperature -10°C (14°F) or higher

TYPICAL MALFUNCTION THRESHOLDS

P040000 (except Brazil OBD Phase 3)
Manifold pressure change* Less than 1.72 kPa [0.25 psi] (at engine speed 1000 rpm)

P04019C (except Brazil OBD Phase 3)
Manifold pressure change* Less than 1.72 kPa [0.25 psi] (at engine speed 1000 rpm)
Manifold pressure Less than 41.5 kPa [6.02 psi]

P04029B (except Brazil OBD Phase 3)
Manifold pressure change* Less than 1.72 kPa [0.25 psi] (at engine speed 1000 rpm)
Manifold pressure 41.5 kPa [6.02 psi] or more

*: Calculated by EGR valve open and close -

P04019C (for Brazil OBD Phase 3)
Manifold pressure change Less than 1.75 kPa [0.25 psi]
At engine speed 1200 rpm

CONFIRMATION DRIVING PATTERN

A222619E19
0.073,1.156 1.104,1.854 1.031,0.698 10 false 65 km/h or more [Engine running] 0.75,2.156 1.667,2.354 0.917,0.198 10 false Idling 0.063,2.375 1.125,2.833 1.063,0.458 10 false Power Switch on (IG) 1.646,2.958 3.177,3.156 1.531,0.198 10 false Warming up 2.49,2.979 5.24,3.177 2.75,0.198 10 false 10 seconds or more 1.99,2.021 2.448,2.219 0.458,0.198 10 false [A] 2.833,1.49 3.292,1.688 0.458,0.198 10 false [B] 4.344,2.021 4.802,2.219 0.458,0.198 10 false [C] 4.052,2.938 4.771,3.448 0.719,0.51 10 false 30 seconds or more 5.292,2.917 5.969,3.417 0.677,0.5 10 false 5 seconds or more 5.063,1.021 5.521,1.219 0.458,0.198 10 false [D] 5.625,1.552 6.083,1.75 0.458,0.198 10 false [E] 6.156,3.375 6.615,3.573 0.458,0.198 10 false [F] 6.563,2.76 7.073,3.094 0.51,0.333 10 false Time 0.594,0.031 1.875,0.375 1.281,0.344 10 false Vehicle Speed

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG).

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the power switch off and wait for at least 30 seconds.

6.

Turn the power switch on (IG).

7.

Turn the GTS on.

8.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

9.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [A].

10.

With the engine running, accelerate the vehicle to 65 km/h (40 mph) or more by depressing the accelerator pedal for at least 10 seconds [B].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

When accelerating the vehicle, depress the accelerator pedal more than normal to start the engine.


11.

Idle the engine for 30 seconds or more [C].

12.

With the shift lever in S and the engine running, accelerate the vehicle to 65 km/h (40 mph) or more [D].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

If the engine stops, further depress the accelerator pedal to restart the engine.


13.

Perform the fuel cut operation for 5 seconds or more, with the accelerator pedal fully released [E].

14.

Enter the following menus: Powertrain / Engine / Trouble Codes [F].

15.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



16.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

17.

Input the DTC P040000, P04019C or P04029B.

18.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system has a malfunction.

·

If the judgment result is INCOMPLETE, perform the steps [A] through [F] again.




CAUTION / NOTICE / HINT

NOTICE:
·

Vehicle Control History may be stored in the hybrid vehicle control ECU assembly if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the Freeze Frame Data and Vehicle Control History can be useful for troubleshooting.

- for Nickel Metal Hydride Battery: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>VEHICLE CONTROL HISTORY

- for Lithium-ion Battery: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY)>VEHICLE CONTROL HISTORY

(Select Powertrain in Health Check and then check the time stamp data.)

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>DTC CHECK / CLEAR

·

If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU assembly, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.

- for Nickel Metal Hydride Battery: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>VEHICLE CONTROL HISTORY

- for Lithium-ion Battery: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY)>VEHICLE CONTROL HISTORY



HINT:
·

By using the Control the EGR Step Position Active Test, the operation of the EGR valve can be checked.

·

If the EGR valve is normal and is opened using the Active Test, the Data List value changes as follows.

Data List Item Change in Data List when Number of Steps is Increased Using Control the EGR Step Position Active Test
Intake Manifold Absolute Pressure Pressure rises

·

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P040000, P04019C, P04029B)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTC P040000, P04019C or P04029B is output A
DTC P040000, P04019C or P04029B and other DTCs are output B


HINT:

If any DTCs other than P040000, P04019C or P04029B are output, troubleshoot those DTCs first.




A

2.READ VALUE USING GTS (INTAKE MANIFOLD ABSOLUTE PRESSURE)

B

2.READ VALUE USING GTS (INTAKE MANIFOLD ABSOLUTE PRESSURE)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Intake Manifold Absolute Pressure.

Powertrain > Engine > Data List
Tester Display
Intake Manifold Absolute Pressure
50003 372 385

e.

Read the value of Intake Manifold Absolute Pressure.

Standard:
GTS Display Specified Condition
Intake Manifold Absolute Pressure 80 to 110 kPa (11.6 to 15.95 psi)



Result:
Proceed to
OK
NG



OK

3.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)

NG

REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR

3.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Put the engine in Inspection Mode (Maintenance Mode).

Powertrain > Hybrid Control > Utility
Tester Display
Inspection Mode
50005 397 2103

e.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher.

HINT:

The A/C switch and all accessories should be off.



f.

Enter the following menus: Powertrain / Engine / Active Test / Control the EGR Step Position / Data List / Intake Manifold Absolute Pressure, Coolant Temperature and Engine Independent.

Powertrain > Engine > Active Test
Active Test Display
Control the EGR Step Position
Data List Display
Intake Manifold Absolute Pressure
Coolant Temperature
Engine Independent
50004 372 25 385,205,428

g.

According to the display on the GTS, compare the values of Data List item Intake Manifold Absolute Pressure before and while performing the Active Test.

NOTICE:
·

Make sure that the value of Data List item Engine Independent is "Operate" while performing the Active Test.

·

Do not leave the EGR valve open for 10 seconds or more during the Active Test.

·

Be sure to return the EGR valve to step 0 when the Active Test is completed.

·

Do not open the EGR valve 30 steps or more during the Active Test.



Standard:

The value of Intake Manifold Absolute Pressure changes according to the EGR valve step set by the Active Test.

Data List Control the EGR Step Position (Active Test)
Before Active Test
(Engine idling)
0 Steps 0 to 30 Steps
(Engine idling)
Intake Manifold Absolute Pressure 20 to 40 kPa (2.9 to 5.8 psi) (EGR valve is fully closed) Intake Manifold Absolute Pressure value is at least +10 kPa (1.45 psi) higher than when EGR valve is fully closed


HINT:
·

If the value of Data List item Engine Independent is "Not Opr" when the engine is idling, charge control is being performed. Perform the Active Test after charge control is complete ("Operate" is displayed).

·

While performing the Active Test, if the increase in the value of Intake Manifold Absolute Pressure is small, the EGR valve assembly may be malfunctioning.

·

Even if the EGR valve assembly is malfunctioning, rough idling or an increase in the value of Intake Manifold Absolute Pressure may occur while performing the Active Test. However, the amount that the value of Intake Manifold Absolute Pressure increases will be smaller than normal.



Result:
Result Proceed to
Before performing the Active Test (while the engine is idling), the value of Intake Manifold Absolute Pressure is not between 20 to 40 kPa (2.9 to 5.8 psi). A
When performing the Active Test to change the EGR valve step between 0 (EGR valve fully closed) and 30, the value of Intake Manifold Absolute Pressure changes less than 10 kPa (1.45 psi). B
Other than above C




A

4.CHECK INTAKE SYSTEM

B

6.REPLACE EGR VALVE ASSEMBLY

C

12.CLEAR DTC
4.CHECK INTAKE SYSTEM
a.

Check the intake system for vacuum leaks.

Click hereEngine / Hybrid System>A25A-FXS (INTAKE / EXHAUST)>INTAKE SYSTEM>ON-VEHICLE INSPECTION

OK:

No leaks from intake system.


HINT:

Perform "Inspection After Repair" after repairing or replacing the intake system.

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>INITIALIZATION



Result:
Proceed to
OK
NG



OK

5.INSPECT EGR VALVE ASSEMBLY

NG

REPAIR OR REPLACE INTAKE SYSTEM

5.INSPECT EGR VALVE ASSEMBLY
a.

b.

Check if the EGR valve is stuck open.

OK:

EGR valve is tightly closed.


HINT:

Perform "Inspection After Repair" after replacing the EGR valve assembly.

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>INITIALIZATION



Result:
Proceed to
OK
NG



OK

REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR

NG

6.REPLACE EGR VALVE ASSEMBLY
a.

Replace the EGR valve assembly.

Click hereEngine / Hybrid System>A25A-FXS (EMISSION CONTROL)>EGR VALVE>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the EGR valve assembly.

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

7.CLEAR DTC
7.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the power switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

8.CHECK WHETHER DTC OUTPUT RECURS (DTC P040000, P04019C OR P04029B)
8.CHECK WHETHER DTC OUTPUT RECURS (DTC P040000, P04019C OR P04029B)
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


b.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 372 20

c.

Input the DTC: P040000, P04019C or P04029B.


d.

Check the DTC judgment result.

Result:
Result Proceed to
NORMAL
(DTCs are not output)
A
ABNORMAL
(DTC P040000, P04019C or P04029B is output)
B




A

END

B

9.REPLACE EGR COOLER ASSEMBLY
9.REPLACE EGR COOLER ASSEMBLY
a.

Replace the EGR cooler assembly.

Click hereEngine / Hybrid System>A25A-FXS (EMISSION CONTROL)>EGR COOLER>REMOVAL

HINT:
·

If any of the EGR system related pipes (EGR pipe, exhaust manifold, etc.) are cracked, damaged or clogged, replace them as necessary.

·

Perform "Inspection After Repair" after replacing the EGR system.

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>INITIALIZATION




Result:
Proceed to
NEXT



NEXT

10.CLEAR DTC
10.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the power switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

11.CHECK WHETHER DTC OUTPUT RECURS (DTC P040000, P04019C OR P04029B)
11.CHECK WHETHER DTC OUTPUT RECURS (DTC P040000, P04019C OR P04029B)
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


b.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 372 20

c.

Input the DTC: P040000, P04019C or P04029B.


d.

Check the DTC judgment result.

Result:
GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions





Result:
Proceed to
NEXT



NEXT

END

12.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the power switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

13.CHECK WHETHER DTC OUTPUT RECURS (DTC P040000, P04019C OR P04029B)
13.CHECK WHETHER DTC OUTPUT RECURS (DTC P040000, P04019C OR P04029B)
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


b.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 372 20

c.

Input the DTC: P040000, P04019C or P04029B.


d.

Check the DTC judgment result.

Result:
Result Proceed to
NORMAL
(DTCs are not output)
A
ABNORMAL
(DTC P040000, P04019C or P04029B is output)
B


HINT:

Perform "Inspection After Repair" after replacing the EGR valve assembly.

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>INITIALIZATION




A

END

B