Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2022.01
RM33C0E _57 Power Source / Network _065454 NETWORKING _0329710 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Tire Pressure Monitor ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Tire Pressure Monitor ECU Communication Stop Mode Any of the following conditions are met:
·

Communication stop for "Tire Pressure" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication stop history for "Tire Pressure" is indicated on the "Communication Bus Check (Detail)" screen of the GTS. (The Lost Communication Time value for "Tire Pressure" is 6 or more.)

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Tire Pressure Monitor ECU Communication Stop Mode" in "DTC Combination Table" are output.

Click here(Click here)


·

Tire pressure warning ECU and receiver branch line or connector

·

Power source circuit of tire pressure warning ECU and receiver

·

Tire pressure warning ECU and receiver ground circuit

·

Tire pressure warning ECU and receiver



WIRING DIAGRAM

C469080E01
0.625,1.958 3.427,2.271 2.802,0.313 10 false No. 3 Junction Connector 0.292,1.958 0.677,2.219 0.385,0.26 10 false R99 1.719,1.448 2.052,1.708 0.333,0.26 10 false 19 1.76,0.865 2.094,1.125 0.333,0.26 10 false 8 5.396,0.865 5.729,1.125 0.333,0.26 10 false 9 5.375,1.427 5.708,1.688 0.333,0.26 10 false 10 5.385,2.344 5.719,2.604 0.333,0.26 10 false 1 5.385,3.177 5.719,3.438 0.333,0.26 10 false 7 3.917,2.313 4.958,2.615 1.042,0.302 10 false ECU-IG1 NO. 4 1.688,2.458 3.25,2.771 1.563,0.313 10 false from IG1-NO. 1 Relay 5.385,3.99 5.719,4.25 0.333,0.26 10 false 12 5.656,4.135 6.073,4.396 0.417,0.26 10 false GND 5.667,3.302 6,3.563 0.333,0.26 10 false +B 5.667,2.5 6,2.76 0.333,0.26 10 false IG 5.656,0.99 6.281,1.24 0.625,0.25 10 false CANH 5.667,1.573 6.344,1.885 0.677,0.313 10 false CANL 5.063,4.781 5.698,5.083 0.635,0.302 10 false R127 5.448,4.781 6.833,5.417 1.385,0.635 10 false Tire Pressure Warning ECU and Receiver 3.885,3.125 5.219,3.438 1.333,0.313 10 false ECU-B NO. 2 1.698,3.281 3.219,3.958 1.521,0.677 10 false from Auxiliary Battery

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the power switch on (IG) and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (TIRE PRESSURE WARNING ECU AND RECEIVER BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the R127 tire pressure warning ECU and receiver connector.


c.
C482146C02
1.5,0.51 1.917,0.771 0.417,0.26 1.979,3.01 1.813,3.01 1.813,3.01 1.813,2.25 true 1.427,3.01 1.615,3.01 1.615,3.01 1.615,2.25 true 0.115,0.063 0.427,0.26 0.313,0.198 10 false *a 1.552,0.563 2.01,0.76 0.458,0.198 10 false R127 2.063,2.927 2.583,3.188 0.521,0.26 10 false CANL 0.99,2.927 1.51,3.188 0.521,0.26 10 false CANH
*a Front view of wire harness connector
(to Tire Pressure Warning ECU and Receiver)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R127-9 (CANH) - R127-10 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (TIRE PRESSURE WARNING ECU AND RECEIVER)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C482146C03
1.5,0.479 1.917,0.74 0.417,0.26 1.021,2.813 1.188,2.813 1.188,2.813 1.188,2.229 true 2.375,2.833 2.208,2.833 2.208,2.833 2.208,2.25 true 1.021,0.875 1.188,0.875 1.188,0.875 1.188,1.792 true 0.115,0.063 0.427,0.26 0.313,0.198 10 false *a 1.552,0.521 2.01,0.719 0.458,0.198 10 false R127 0.781,2.729 1.052,2.938 0.271,0.208 10 false +B 2.458,2.76 2.885,2.979 0.427,0.219 10 false GND 0.823,0.792 1.177,1.042 0.354,0.25 10 false IG
*a Front view of wire harness connector
(to Tire Pressure Warning ECU and Receiver)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R127-12 (GND) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) auxiliary battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
R127-1 (IG) - Body ground Power switch on (IG) 11 to 14 V
R127-7 (+B) - Body ground Power switch off 11 to 14 V



Result:
Result
OK
NG



OK

REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)