Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM › from 2022.01
RM33C0E _53 Suspension _065440 TIRE PRESSURE MONITORING _0329663 TIRE PRESSURE WARNING SYSTEM C

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  C2179  Tire Pressure Monitor ECU Communication Stop  


DESCRIPTION

The main body ECU (multiplex network body ECU) sends signals to the tire pressure warning ECU and receiver via a direct line.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
C2179 Tire Pressure Monitor ECU Communication Stop Communication between the main body ECU (multiplex network body ECU) and tire pressure warning ECU and receiver is interrupted for 10 seconds or more.
·

Main body ECU (Multiplex network body ECU)

·

Wire harness or connector

·

Tire pressure warning ECU and receiver


-

WIRING DIAGRAM

C385230E39
1.292,2.948 1.75,3.146 0.458,0.198 10 false CPU 2.188,2.719 2.646,2.917 0.458,0.198 10 false PRG 4.698,2.854 5.156,3.052 0.458,0.198 10 false PRG 4.677,1.302 5.135,1.5 0.458,0.198 10 false +B 4.688,0.563 5.146,0.76 0.458,0.198 10 false IG 3.375,1.458 4.365,1.646 0.99,0.188 10 false ECU-B NO. 2 3.333,0.719 4.323,0.906 0.99,0.188 10 false ECU-IG1 NO. 4 1.708,1.281 3.052,1.49 1.344,0.208 10 false from J/B-B Fuse 1.844,0.552 3.208,0.781 1.365,0.229 10 false from IG Circuit 4.417,1.156 4.875,1.354 0.458,0.198 10 false 7 4.427,0.417 4.885,0.615 0.458,0.198 10 false 1 4.406,2.708 4.865,2.906 0.458,0.198 10 false 5 2.604,2.708 3.063,2.906 0.458,0.198 10 false 11 0.396,3.656 0.854,3.854 0.458,0.198 10 false K53 4.125,3.615 4.583,3.813 0.458,0.198 10 false R127 4.125,3.792 6.76,4.094 2.635,0.302 10 false Tire Pressure Warning ECU and Receiver 0.396,3.823 3.76,4.115 3.365,0.292 10 false Main Body ECU (Multiplex Network Body ECU)

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the tire pressure warning ECU and receiver, read the transmitter IDs and number of the transmitters (4 or 5) stored in the old ECU using the GTS and write them down before removal.

·

It is necessary to perform initializationSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION after registrationSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION of the transmitter IDs into the tire pressure warning ECU and receiver after the ECU has been replaced.

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.



PROCEDURE

1.INSPECT MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (OUTPUT WAVEFORM)
a.
C385231C04
1.219,0.219 1.615,0.448 0.396,0.229 0.865,1.729 1.156,1.094 true 0.208,0.229 0.521,0.427 0.313,0.198 10 false *a 2.875,3.406 3.188,3.604 0.313,0.198 10 false *b 0.719,1.771 1.125,2 0.406,0.229 10 false PRG 1.292,0.25 1.698,0.479 0.406,0.229 10 false K53
*a Component with harness connected
(Main Body ECU (Multiplex Network Body ECU))
*b GND


Using an oscilloscope, check the waveform.

NOTICE:

With the connector connected, check from the backside of the connector.


OK:
Tester Connection Tool Setting Range Condition Specified Condition
K53-11 (PRG) - Body ground 5 V/DIV.5 ms./DIV. Power switch on (IG) Waveform generation



Result:
Result Proceed to
Waveform is as shown in the illustration. (Waveform alternates between 9.8 V or higher and 1.2 V or less) A
Waveform does not change from 9.8 V or higher B
Waveform does not change from 1.2 V or less C



A

REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

2.CHECK TERMINAL VOLTAGE (TIRE PRESSURE WARNING ECU AND RECEIVER OUTPUT)
2.CHECK TERMINAL VOLTAGE (TIRE PRESSURE WARNING ECU AND RECEIVER OUTPUT)
a.

Disconnect the K53 main body ECU (multiplex network body ECU) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K53-11 (PRG) - Body ground Power switch on (IG) 9.8 V or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

3.CHECK HARNESS AND CONNECTOR (TIRE PRESSURE WARNING ECU AND RECEIVER - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
3.CHECK HARNESS AND CONNECTOR (TIRE PRESSURE WARNING ECU AND RECEIVER - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Turn the power switch off.


b.

Disconnect the R127 tire pressure warning ECU and receiver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R127-5 (PRG) - K53-11 (PRG) Always Below 1 Ω
R127-5 (PRG) or K53-11 (PRG) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (POWER SUPPLY - TIRE PRESSURE WARNING ECU AND RECEIVER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (POWER SUPPLY - TIRE PRESSURE WARNING ECU AND RECEIVER)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
R127-7 (+B) - Body ground Always 10 to 16 V
R127-1 (IG) - Body ground Power switch on (IG) 10 to 16 V



Result:
Proceed to
OK
NG



OK

REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR