With the front panel and side panel No.1 LH removed.
REMOVAL
| Symbol Meaning | |
|---|---|
|
Remove Weld Points |
|
Remove Weld Points |
|
Cut with Disc Sander etc. |
|
Cut and Join Location |
|
Cut Location for Supply Parts |
| *A | LH | - | - |
| *a | mm (in.) | - | - |
| *A | LH | - | - |
| *A | RH | - | - |
| *a | mm (in.) | - | - |
| *A | RH | - | - |
INSTALLATION
| Symbol Meaning | |
|---|---|
|
Plug Weld |
|
Plug Weld |
|
Cut and Join Location |
|
Fillet Weld |
|
Butt Weld |
|
Body Sealer |
Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.
Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)
Before installing a new part, apply body sealer.
Apply body sealer in an even, continuous bead.
Before temporarily installing the new parts, weld the No.1 outer pillar lower, No.1 inner pillar sub-assembly, hood reinforcement gusset, mounting bracket sub-assembly and outer side mirror retainer with the standard number of welding points. (w/o Snorkel Air Cleaner)
Before temporarily installing the new parts, weld the No.1 outer pillar lower, No.1 inner pillar sub-assembly, hood reinforcement gusset, mounting bracket sub-assembly, outer side mirror retainer and air cleaner inlet pipe retainer with the standard number of welding points. (w/ Snorkel Air Cleaner)
After welding the No.1 outer pillar lower, No.1 inner pillar sub-assembly, hood reinforcement gusset, mounting bracket sub-assembly and outer side mirror retainer to the vehicle side, install the No.1 side panel. (w/o Snorkel Air Cleaner)
After welding the No.1 outer pillar lower, No.1 inner pillar sub-assembly, hood reinforcement gusset, mounting bracket sub-assembly, outer side mirror retainer and air cleaner inlet pipe retainer to the vehicle side, install the No.1 side panel. (w/ Snorkel Air Cleaner)
After welding, apply body sealer to the corresponding parts. (See the painting / coating)
After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.
Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.
Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)
Before temporarily installing the new parts, weld the front side panel bracket No.2, front body pillar outer, front fender rear extension, front bumper bracket, front bumper side blacket, pillar shear gusset No.1, No.1 pillar reinforcement upper, door check arm bracket, No.1 pillar reinforcement lower and front door pillar patch with the standard number of welding points. (w/o Snorkel Air Cleaner)
Before temporarily installing the new parts, weld the front side panel bracket No.2, front body pillar outer, front fender rear extension, front bumper bracket, front bumper side blacket, pillar shear gusset No.1, No.1 pillar reinforcement upper, door check arm bracket, No.1 pillar reinforcement lower, front door pillar patch and air cleaner inlet pipe retainer with the standard number of welding points. (w/ Snorkel Air Cleaner)
Before installing a new part, apply body sealer.
Apply body sealer in an even, continuous bead.
After welding the No.1 inner pillar sub-assembly to the vehicle side, install the front side panel bracket No.2, front body pillar outer, front fender rear extension, front bumper bracket, front bumper side blacket, pillar shear gusset No.1, No.1 pillar reinforcement upper, door check arm bracket, No.1 pillar reinforcement lower and front door pillar patch. (w/o Snorkel Air Cleaner)
After welding the No.1 inner pillar sub-assembly to the vehicle side, install the front side panel bracket No.2, front body pillar outer, front fender rear extension, front bumper bracket, front bumper side blacket, pillar shear gusset No.1, No.1 pillar reinforcement upper, door check arm bracket, No.1 pillar reinforcement lower, front door pillar patch and air cleaner inlet pipe retainer. (w/ Snorkel Air Cleaner)
After welding, apply body sealer to the corresponding parts. (See the painting / coating)
After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.
| *A | LH | *B | w/ Snorkel Air Cleaner |
| *1 | NO.1 OUTER PILLAR LOWER | *2 | NO.1 INNER PILLAR SUB-ASSEMBLY |
| *3 | HOOD REINFORCEMENT GUSSET | *4 | MOUNTING BRACKET SUB-ASSEMBLY |
| *5 | OUTER SIDE MIRROR RETAINER | *6 | AIR CLEANER INLET PIPE RETAINER |
| *a | mm (in.) | - | - |
| *A | LH | - | - |
| *a | mm (in.) | - | - |
| *A | LH | - | - |
| *A | LH | - | - |
| *1 | NO.1 SIDE PANEL | - | - |
| *A | RH | *B | w/ Snorkel Air Cleaner |
| *1 | FRONT SIDE PANEL BRACKET NO.2 | *2 | FRONT BODY PILLAR OUTER |
| *3 | FRONT FENDER REAR EXTENSION | *4 | FRONT BUMPER BRACKET |
| *5 | FRONT BUMPER SIDE BLACKET | *6 | PILLAR SHEAR GUSSET NO.1 |
| *7 | NO.1 PILLAR REINFORCEMENT UPPER | *8 | DOOR CHECK ARM BRACKET |
| *9 | NO.1 PILLAR REINFORCEMENT LOWER | *10 | FRONT DOOR PILLAR PATCH |
| *11 | AIR CLEANER INLET PIPE RETAINER | - | - |
| *A | RH | - | - |
| *1 | NO.1 INNER PILLAR SUB-ASSEMBLY | - | - |
| *a | mm (in.) | - | - |
| *A | RH | - | - |