Home › Vehicle Exterior › BODY PANEL › SIDE PANEL NO.1 LH (for RHD)
BM2850E _01 Vehicle Exterior _075893 BODY PANEL _0369107 SIDE PANEL NO.1 LH(for RHD) F

BODY PANEL  SIDE PANEL NO.1 LH(for RHD)  ASSEMBLY REPLACEMENT  


K139850

REMOVAL


Symbol MeaningRe
K108818

Remove Weld Points


REMOVAL POINT
1.

*a in illustration above indicates where the adhesive is located.

2.

Roughly cut open the panel so that the adhesive can be reached. Cut through the adhesive with a cut chisel to remove the panel.

HINT:

In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.



K146119C01
2.698,6.531 2.563,5.49 false 2.698,6.531 2.781,5.49 false 2.708,6.531 2.958,5.49 false 2.708,6.531 2.927,6.531 false 4.74,6.521 4.5,6.521 4.5,6.521 4.406,5.479 false 0.281,0.385 0.594,0.542 0.313,0.156 10 false *A 2.969,6.458 3.281,6.656 0.313,0.198 10 false *a 4.792,6.448 5.104,6.646 0.313,0.198 10 false *a
*A for Glide Type - -


K146120C02
2.75,6.552 2.563,5.49 false 2.75,6.542 2.781,5.49 false 2.75,6.542 2.958,5.5 false 2.75,6.542 3.052,6.542 false 4.417,5.479 4.531,6.563 4.531,6.563 4.802,6.563 false 3.104,6.49 3.417,6.688 0.313,0.198 10 false *a 4.854,6.479 5.167,6.677 0.313,0.198 10 false *a 0.396,0.583 0.708,0.781 0.313,0.198 10 false *A
*A for Folding Type - -


K146122C02
0.438,0.365 0.75,0.521 0.313,0.156 10 false *A 0.469,4.677 0.781,4.833 0.313,0.156 10 false *B
*A for Glide Type *B for Folding Type


K147921

INSTALLATION


Symbol Meaning
K108823

Plug Weld
K108834

Body Sealer


INSTALLATION POINT
1.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.

2.

Before temporarily installing the new parts, weld the front side panel outer,electrical part bracket and mudguard bracket front with the standard number of welding points.

3.

Before installing a new part, apply body sealer.

HINT:
·

Apply body sealer evenly about 5 mm (0.20 in.) from the flange, avoiding any oozing.

·

Apply body sealer evenly, about 3 to 4 mm (0.12 to 0.16 in.) in diameter.



4.

Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115) to the area indicated by *a in the illustration.

HINT:
·

Apply a light coat of adhesive around the plug welding points.

·

Apply enough adhesive to the panels.



5.

After welding, apply body sealer to the corresponding parts. (See the painting / coating)

6.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.


K147922C01
2.823,3.135 2.969,2.115 2.969,2.115 3.135,2.115 false 2.323,4.594 1.823,5.438 1.823,5.438 1.99,5.438 false 4.01,4.219 3.646,4.833 3.646,4.833 3.813,4.833 false 3.188,2.031 3.5,2.229 0.313,0.198 10 false *1 2.021,5.354 2.333,5.552 0.313,0.198 10 false *2 3.844,4.75 4.156,4.948 0.313,0.198 10 false *3
*1 FRONT SIDE PANEL OUTER *2 ELECTRICAL PART BRACKET
*3 MUDGUARD BRACKET FRONT - -


K146125C02
2.156,2.01 0.74,0.74 0.74,0.74 0.958,0.74 false 2.74,5.552 2.792,4.563 false 2.729,5.552 2.563,4.552 false 2.75,5.552 2.969,4.552 false 2.948,5.552 2.74,5.552 false 4.792,5.521 4.542,5.521 4.542,5.521 4.417,4.542 false 2.813,6.771 3.385,6.969 0.573,0.198 10 false 5 (0.20) 0.323,0.333 0.635,0.49 0.313,0.156 10 false *A 1.021,0.677 1.333,0.833 0.313,0.156 10 false *1 2.99,5.479 3.302,5.635 0.313,0.156 10 false *a 4.844,5.458 5.156,5.615 0.313,0.156 10 false *a 0.26,8.531 0.573,8.688 0.313,0.156 10 false *b
*A for Glide Type - -
*1 FRONT BUMPER SIDE BRACKET - -
*b mm (in.) - -


K146126C02
2.125,1.979 0.813,1.135 0.813,1.135 1.073,1.135 false 2.719,5.688 2.563,4.542 false 2.729,5.688 2.792,4.542 false 2.74,5.688 2.969,4.542 false 2.729,5.688 2.938,5.688 false 4.729,5.688 4.521,5.688 4.521,5.688 4.417,4.51 false 0.365,0.26 0.677,0.417 0.313,0.156 10 false *A 1.115,1.083 1.427,1.24 0.313,0.156 10 false *1 2.813,6.792 3.385,7.031 0.573,0.24 10 false 5 (0.20) 2.969,5.635 3.281,5.792 0.313,0.156 10 false *a 4.76,5.625 5.073,5.781 0.313,0.156 10 false *a 0.156,8.615 0.469,8.771 0.313,0.156 10 false *b
*A for Folding Type - -
*1 FRONT BUMPER SIDE BRACKET - -
*b mm (in.) - -


K146128C02
0.469,0.354 0.781,0.51 0.313,0.156 10 false *A 0.458,4.667 0.771,4.823 0.313,0.156 10 false *B
*A for Glide Type *B for Folding Type


K147923