Home › Vehicle Exterior › BODY PANEL › SIDE PANEL NO.1 RH(for LHD)
BM2850E _01 Vehicle Exterior _075893 BODY PANEL _0369058 SIDE PANEL NO.1 RH(for LHD) F

BODY PANEL  SIDE PANEL NO.1 RH(for LHD)  ASSEMBLY REPLACEMENT  


K139981

REMOVAL



Symbol Meaning
K108818

Remove Weld Points

REMOVAL
1.

*a in illustration above indicates where the adhesive is located.

2.

Roughly cut open the panel so that the adhesive can be reached. Cut through the adhesive with a cut chisel to remove the panel.

HINT:

In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.



K148373C01
2.417,7.167 2.583,7.167 2.583,7.167 2.698,6.052 false 4.333,7.167 4.5,7.167 4.5,7.167 4.354,6.063 false 4.5,7.167 4.167,6.042 false 4.5,7.167 4.563,6.063 false 0.25,0.167 0.563,0.365 0.313,0.198 10 false *A 2.229,7.073 2.542,7.271 0.313,0.198 10 false *a 4.146,7.073 4.458,7.271 0.313,0.198 10 false *a
*A for Glide Type - -


K147924C01
2.76,6.26 2.594,6.26 2.594,6.26 2.729,5.49 false 4.521,6.26 4.354,6.26 4.354,6.26 4.156,5.49 false 4.365,6.25 4.344,5.49 false 4.365,6.24 4.531,5.49 false 2.792,6.156 3.104,6.354 0.313,0.198 10 false *a 4.563,6.177 4.875,6.375 0.313,0.198 10 false *a 0.25,0.167 0.563,0.365 0.313,0.198 10 false *A
*A for Folding Type - -


K148374C01
0.5,0.5 6.667,8.417 6.167,7.917 0.5,4.5 6.667,4.5 false 0.667,0.667 0.979,0.823 0.313,0.156 10 false *A 0.667,4.667 0.979,4.823 0.313,0.156 10 false *B
*A for Glide Type *B for Folding Type


K148375

INSTALLATION


Symbol Meaning
K108823

Plug Weld
K108834

Body Sealer


INSTALLATION POINT
1.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.

2.

Before temporarily installing the new parts, weld the front side panel outer,electrical part bracket and mudguard bracket front with the standard number of welding points.

3.

Before installing a new part, apply body sealer.

HINT:
·

Apply body sealer evenly about 5 mm (0.20 in.) from the flange, avoiding any oozing.

·

Apply body sealer evenly, about 3 to 4 mm (0.12 to 0.16 in.) in diameter.



4.

Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115) to the area indicated by *a in the illustration.

HINT:
·

Apply a light coat of adhesive around the plug welding points.

·

Apply enough adhesive to the panels.



5.

After welding, apply body sealer to the corresponding parts. (See the painting / coating)

6.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.


K147926C01
4.396,3.521 4.208,2.708 4.208,2.708 4.375,2.708 false 4.646,4.958 4.875,5.792 4.875,5.792 5.042,5.792 false 3.167,5.156 3.333,5.156 3.333,5.156 2.979,4.573 false 4.396,2.625 4.708,2.823 0.313,0.198 10 false *1 2.99,5.073 3.302,5.271 0.313,0.198 10 false *3 5.063,5.708 5.375,5.906 0.313,0.198 10 false *2
*1 FRONT SIDE PANEL OUTER *2 ELECTRICAL PART BRACKET
*3 MUDGUARD BRACKET FRONT - -


K148376C01
4.927,2.833 5.135,3.292 5.135,3.292 5.302,3.292 false 2.656,5.104 2.583,6 2.583,6 2.417,6 false 4.177,5.115 4.25,6 4.25,6 4.417,6 false 4.25,6 4.333,5.115 false 4.25,6 4.563,5.115 false 5.344,3.219 5.656,3.417 0.313,0.198 10 false *1 2.25,5.917 2.563,6.115 0.313,0.198 10 false *a 4.49,5.906 4.802,6.104 0.313,0.198 10 false *a 0.198,8.438 0.51,8.635 0.313,0.198 10 false *b 3.969,7.365 4.49,7.594 0.521,0.229 10 false 5 (0.20) 0.188,0.219 0.5,0.417 0.313,0.198 10 false *A
*A for Glide Type - -
*1 FRONT BUMPER SIDE BLACKET - -
*b mm (in.) - -


K147927C02
4.896,2.354 5.104,2.813 5.104,2.813 5.271,2.813 false 2.719,4.542 2.615,5.417 2.615,5.417 2.781,5.417 false 4.167,4.531 4.271,5.354 4.271,5.354 4.438,5.354 false 4.271,5.354 4.333,4.542 false 4.281,5.344 4.542,4.552 false 5.302,2.719 5.615,2.917 0.313,0.198 10 false *1 2.823,5.323 3.135,5.521 0.313,0.198 10 false *a 4.5,5.281 4.813,5.479 0.313,0.198 10 false *a 0.198,8.438 0.51,8.635 0.313,0.198 10 false *b 3.854,6.76 4.375,6.99 0.521,0.229 10 false 5 (0.20) 0.188,0.219 0.5,0.417 0.313,0.198 10 false *A
*A for Folding Type - -
*1 FRONT BUMPER SIDE BLACKET - -
*b mm (in.) - -


K148377C01
0.5,0.5 6.667,8.417 6.167,7.917 0.5,4.5 6.667,4.5 false 0.667,0.667 0.979,0.823 0.313,0.156 10 false *A 0.688,4.677 1,4.833 0.313,0.156 10 false *B
*A for Glide Type *B for Folding Type


K148378