Home › Vehicle Exterior › BODY PANEL › SIDE PANEL NO.4 LH
BM2850E _01 Vehicle Exterior _075893 BODY PANEL _0369063 SIDE PANEL NO.4 LH F

BODY PANEL  SIDE PANEL NO.4 LH  CUT AND JOIN REPLACEMENT SECTIONS  


K139858

REMOVAL



Symbol Meaning
K108818

Remove Weld Points
K108820

Remove Weld Points
K108827

Cut and Join Location

REMOVAL POINT
1.

*a in illustration above indicates where the adhesive is located.

2.

Roughly cut open the panel so that the adhesive can be reached. Cut through the adhesive with a cut chisel to remove the panel.

HINT:

In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.



K146181C02
0.854,6.771 1.094,6.771 1.094,6.771 1.906,7.927 false 0.115,8.573 0.427,8.729 0.313,0.156 10 false *b 0.698,6.698 1.01,6.854 0.313,0.156 10 false *a 0.302,1.375 0.99,1.573 0.688,0.198 10 false 95 (3.74) 5.458,2.854 5.771,3.01 0.313,0.156 10 false *1 5.458,4.646 5.771,4.802 0.313,0.156 10 false *2 5.438,6.583 5.75,6.74 0.313,0.156 10 false *3
*1 Rough Cut Panel *2 Grind
*3 After Removing - -
*b mm (in.) - -


K146182C01
0.302,4.125 0.615,4.281 0.313,0.156 10 false *A 3.635,4.125 3.948,4.281 0.313,0.156 10 false *B
*A for Luggage Compartment *B for Double Swing Out Type


INSTALLATION


Symbol Meaning
K108823

Plug Weld
K108825

Plug Weld
K108830

Fillet Weld
K108834

Body Sealer


INSTALLATION POINT
1.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.

2.

Before installing a new part, apply body sealer.

HINT:

Apply body sealer in an even, continuous bead.


3.

Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115) to the area indicated by *a in the illustration.

HINT:
·

Apply a light coat of adhesive around the plug welding points.

·

Apply enough adhesive to the panels.



4.

Follow the welding conditions when welding *b to assure sufficient weld strength.

Plug Diameter Welding Wire Diameter Plug Welding Hole Pitch Shield Gas
4 mm (0.16 in.) 0.6 mm (0.02 in.) 25 mm (0.98 in.) Metal active gas (Ar 80% + CO2 20%))
5 mm (0.20 in.) 0.8 mm (0.03 in.) 30mm (1.18 in.)

5.

After welding, apply body sealer to the corresponding parts. (See the painting / coating)

6.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.


K146183C01
4.104,2.083 4.927,1.875 4.927,1.875 5.104,1.875 false 3.333,6.99 3.094,6.99 3.094,6.99 3.479,5.719 false 3.375,6.927 3.688,7.083 0.313,0.156 10 false *a 5.156,1.823 5.469,2.021 0.313,0.198 10 false *1
*1 NO.4 SIDE PANEL - -


K146184C02
5.094,6.313 5.344,5.833 5.344,5.833 5.552,5.833 false 5.625,5.76 5.938,5.917 0.313,0.156 10 false *1 0.115,8.625 0.427,8.781 0.313,0.156 10 false *c 3.677,0.802 3.99,0.958 0.313,0.156 10 false *b 4.844,2.99 5.156,3.146 0.313,0.156 10 false *b 4.844,3.719 5.156,3.875 0.313,0.156 10 false *b 4.833,4.479 5.146,4.635 0.313,0.156 10 false *b 3.688,1.427 4,1.583 0.313,0.156 10 false *b 1.604,7.625 1.917,7.781 0.313,0.156 10 false *b 4.271,6.271 4.865,6.51 0.594,0.24 10 false 3.7 (0.16) 5.417,7.104 6.115,7.323 0.698,0.219 10 false 11.8 (0.46)
*1 Plug Welding Hole Center - -
*c mm (in.) - -


K146185C01
0.365,4.135 0.677,4.292 0.313,0.156 10 false *A 3.698,4.115 4.01,4.271 0.313,0.156 10 false *B
*A for Luggage Compartment *B for Double Swing Out Type