Home › Vehicle Exterior › BODY PANEL › NO.3 PILLAR(for RHD)
BM2850E _01 Vehicle Exterior _075893 BODY PANEL _0369118 NO.3 PILLAR(for RHD) F

BODY PANEL  NO.3 PILLAR(for RHD)  ASSEMBLY REPLACEMENT  


K139851

With the side panel No.1 LH removed.


REMOVAL


Symbol Meaning
K108818

Remove Weld Points
K108820

Remove Weld Points
K108828

Cut Location for Supply Parts


REMOVAL POINT
1.

*a and *b is reused.

2.

After removing the *a and *b, remove the No.3 pillar.

3.

*c in illustration indicates where the adhesive is located.

4.

Roughly cut open the panel so that the adhesive can be reached. Cut through the adhesive with a cut chisel to remove the panel.

HINT:

In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.



K146199C01
2.708,2.917 2.365,1.948 2.365,1.948 2.146,1.948 false 1.958,4.51 2.104,4.51 2.104,4.51 2.719,4.042 false 3.458,7.292 3.281,7.292 3.281,7.292 3.604,5.969 false 0.25,0.26 0.563,0.417 0.313,0.156 10 false *A 3.49,7.229 3.802,7.385 0.313,0.156 10 false *c 1.979,1.865 2.292,2.021 0.313,0.156 10 false *a 1.802,4.448 2.115,4.604 0.313,0.156 10 false *b
*A for Glide Type - -


K146200C01
0.313,0.219 0.625,0.375 0.313,0.156 10 false *A
*A for Glide Type - -


K146201C01
3.604,7.083 3.406,7.083 3.406,7.083 3.646,5.896 false 1.927,4.479 2.125,4.479 2.125,4.479 2.698,4.01 false 2.688,2.906 2.5,1.906 2.5,1.906 2.313,1.906 false 0.406,0.438 0.719,0.594 0.313,0.156 10 false *A 2.156,1.833 2.469,1.99 0.313,0.156 10 false *a 1.771,4.417 2.083,4.573 0.313,0.156 10 false *b 3.646,7.031 3.958,7.188 0.313,0.156 10 false *c
*A for Folding Type - -


K147969C01
5.25,1.5 5.417,1.5 5.417,1.5 5.833,2 false 5.813,2.063 5.417,1.5 false 5.552,1.948 5.417,1.5 false 0.292,0.24 0.604,0.438 0.313,0.198 10 false *A 5.094,1.406 5.406,1.604 0.313,0.198 10 false *c
*A for Folding Type - -


INSTALLATION


Symbol Meaning
K108821

Spot Weld
K108823

Plug Weld
K108825

Plug Weld
K108831

Butt Weld
K108834

Body Sealer


INSTALLATION POINT (for Glide Type)
1.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.

2.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)

3.

Before installing a new part, apply body sealer.

HINT:

Apply body sealer in an even, continuous bead.


4.

Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115) to the area indicated by *a in the illustration.

HINT:
·

Apply a light coat of adhesive around the plug welding points.

·

Apply enough adhesive to the panels.



5.

Before temporarily installing the new parts, weld the No.3 pillar, center door pillar gusset front, lower rail plate inner No.3, stiffener bracket No.5 and center body piller reinforce sub-assembly lower front with the standard number of welding points.

6.

After welding the No.3 pillar, center door pillar gusset front, lower rail plate inner No.3, stiffener bracket No.5 and center body piller reinforce sub-assembly lower front to the vehicle side, install the *b and *c.

7.

After welding, apply body sealer and undercoating to the corresponding parts. (See the painting / coating)

8.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.


INSTALLATION POINT (for Folding Type)
1.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.

2.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)

3.

Before installing a new part, apply body sealer.

HINT:

Apply body sealer in an even, continuous bead.


4.

Before temporarily installing the new parts, weld the No.3 pillar, center door pillar gusset front, center door orening panel lower inner front, stiffener bracket No.5 and center body pillar plate outer with the standard number of welding points.

5.

Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115) to the area indicated by *a in the illustration.

HINT:
·

Apply a light coat of adhesive around the plug welding points.

·

Apply enough adhesive to the panels.



6.

After welding the No.3 pillar, center door pillar gusset front, center door orening panel lower inner front, stiffener bracket No.5 and center body pillar plate outer to the vehicle side, install the *b and *c.

7.

After welding, apply body sealer and undercoating to the corresponding parts. (See the painting / coating)

8.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.


K146204C02
2.385,0.781 2.063,0.177 2.063,0.177 1.896,0.177 false 3.708,0.677 4.031,0.24 4.031,0.24 4.167,0.24 false 3.354,2.458 2.771,2.021 2.771,2.021 2.583,2.021 false 4.76,3.802 4.552,4.635 4.552,4.635 4.74,4.635 false 3.479,6.531 3.167,5.719 3.167,5.719 2.969,5.719 false 2.396,7.5 2.115,6.458 false 2.302,7.448 2.115,6.458 2.115,6.458 1.938,6.458 false 2.219,7.406 2.104,6.458 false 0.219,0.125 0.531,0.281 0.313,0.156 10 false *A 4.229,0.188 4.542,0.344 0.313,0.156 10 false *1 2.417,1.948 2.729,2.104 0.313,0.156 10 false *2 4.771,4.563 5.083,4.719 0.313,0.156 10 false *3 1.729,0.115 2.042,0.271 0.313,0.156 10 false *4 2.802,5.646 3.115,5.802 0.313,0.156 10 false *5 1.781,6.375 2.094,6.531 0.313,0.156 10 false *a
*A for Glide Type - -
*1 NO.3 PILLAR *2 CENTER DOOR PILLAR GUSSET FRONT
*3 LOWER RAIL PLATE INNER NO.3 *4 STIFFENER BRACKET NO.5
*5 CENTER BODY PILLER REINFORCE SUB-ASSEMBLY LOWER FRONT - -


K146205C01
0.313,0.25 0.625,0.406 0.313,0.156 10 false *A
*A for Glide Type - -


K146206C02
3.625,7.031 3.427,7.031 3.427,7.031 3.615,5.969 false 1.927,4.531 2.094,4.531 2.094,4.531 2.729,4.021 false 2.729,2.917 2.531,2.01 2.531,2.01 2.333,2.01 false 0.198,0.219 0.51,0.375 0.313,0.156 10 false *A 1.76,4.448 2.073,4.604 0.313,0.156 10 false *c 2.156,1.938 2.469,2.094 0.313,0.156 10 false *b 3.667,6.979 3.979,7.135 0.313,0.156 10 false *a
*A for Glide Type - -


K146207C01
3.813,7.094 4.177,7.604 4.177,7.604 4.354,7.604 false 4.719,5.542 4.542,5.542 4.542,5.542 4.677,4.875 false 3.313,3 2.646,2.635 2.646,2.635 2.458,2.635 false 3.708,1.094 4.083,0.573 4.083,0.573 4.271,0.573 false 2.333,1.24 2.042,0.552 2.042,0.552 1.875,0.552 false 0.25,0.135 0.563,0.292 0.313,0.156 10 false *A 4.323,0.5 4.635,0.656 0.313,0.156 10 false *1 2.281,2.563 2.594,2.719 0.313,0.156 10 false *2 4.771,5.469 5.083,5.625 0.313,0.156 10 false *3 1.698,0.49 2.01,0.646 0.313,0.156 10 false *4 4.396,7.552 4.708,7.708 0.313,0.156 10 false *5
*A for Folding Type - -
*1 NO.3 PILLAR *2 CENTER DOOR PILLAR GUSSET FRONT
*3 CENTER DOOR ORENING PANEL LOWER INNER FRONT *4 STIFFENER BRACKET NO.5
*5 CENTER BODY PILLAR PLATE OUTER - -


K147970C02
5.781,1.854 5.417,1.563 false 5.552,1.844 5.406,1.563 false 5.792,1.958 5.417,1.563 5.417,1.563 5.25,1.563 false 0.188,0.167 0.5,0.323 0.313,0.156 10 false *A 5.094,1.49 5.406,1.688 0.313,0.198 10 false *a
*A for Folding Type - -


K146210C02
2.656,2.917 2.49,1.948 2.49,1.948 2.323,1.948 false 1.969,4.427 2.167,4.427 2.167,4.427 2.708,4 false 3.521,7.031 3.323,7.031 3.323,7.031 3.615,5.885 false 0.125,0.156 0.438,0.313 0.313,0.156 10 false *A 2.146,1.885 2.458,2.042 0.313,0.156 10 false *b 1.802,4.365 2.115,4.521 0.313,0.156 10 false *c 3.563,6.99 3.875,7.146 0.313,0.156 10 false *a
*A for Folding Type - -