Home › Vehicle Exterior › BODY PANEL › NO.4 PILLAR (for RHD) › 2017.01–2019.08
BM2850E _01 Vehicle Exterior _075893 BODY PANEL _0369067 NO.4 PILLAR(for RHD) F

BODY PANEL  NO.4 PILLAR(for RHD)  ASSEMBLY REPLACEMENT  


K139852

With the side panel No.1 LH removed.


REMOVAL


Symbol Meaning
K108818

Remove Weld Points
K108820

Remove Weld Points
K108827

Cut and Join Location
K108828

Cut Location for Supply Parts


REMOVAL POINT
1.

*a is reused.

2.

After removing the *a, remove the No.4 pillar.

3.

*b in illustration indicates where the adhesive is located.

4.

Roughly cut open the panel so that the adhesive can be reached. Cut through the adhesive with a cut chisel to remove the panel.

HINT:

In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.



K147976C01
3.292,5.25 3.146,5.25 3.146,5.25 3.042,4.802 false 4.896,4.219 4.74,4.219 4.74,4.219 4.396,3.24 false 0.167,0.292 0.479,0.448 0.313,0.156 10 false *A 4.927,4.146 5.24,4.302 0.313,0.156 10 false *a 3.344,5.167 3.656,5.323 0.313,0.156 10 false *b 3.938,2.563 4.625,2.802 0.688,0.24 10 false 120 (4.72) 0.167,8.583 0.479,8.74 0.313,0.156 10 false *c
*A for Glide Type - -
*c mm (in.) - -


K146212C01
0.198,0.24 0.51,0.396 0.313,0.156 10 false *A
*A for Glide Type - -


K146213C01
3.229,5.375 3.094,5.375 3.094,5.375 2.99,4.917 false 4.823,4.385 4.667,4.385 4.667,4.385 4.302,3.458 false 0.167,0.198 0.479,0.354 0.313,0.156 10 false *A 0.135,8.635 0.448,8.792 0.313,0.156 10 false *c 3.844,2.771 4.594,3 0.75,0.229 10 false 120 (4.72) 4.854,4.313 5.167,4.51 0.313,0.198 10 false *a 3.26,5.302 3.573,5.5 0.313,0.198 10 false *b
*A for Folding Type - -
*c mm (in.) - -


K147977C01
1.542,2.104 1.917,1.75 1.917,1.75 2.083,1.75 false 1.542,2.198 1.917,1.75 false 1.792,2.052 1.917,1.75 false 0.198,0.24 0.51,0.396 0.313,0.156 10 false *A 2.125,1.667 2.281,1.865 0.156,0.198 10 false b
*A for Folding Type - -


INSTALLATION


Symbol Meaning
K108821

Spot Weld
K108823

Plug Weld
K108825

Plug Weld
K108831

Butt Weld
K108834

Body Sealer


INSTALLATION POINT (for Glide Type)
1.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.

2.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)

3.

Before installing a new part, apply body sealer.

HINT:

Apply body sealer in an even, continuous bead.


4.

Before temporarily installing the new parts, weld the No.4 pillar, rear seat gusset, center door pillar gusset rear, lower rail plate inner No.4, stiffener bracket No.5, pillar to rail gusset No.1, quarter panel palte upper No.1, center body pillar reinforce sub-assembly lower rear and center door piller dust proof plate rear with the standard number of welding points.

5.

Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115) to the area indicated by *a in the illustration.

HINT:
·

Apply a light coat of adhesive around the plug welding points.

·

Apply enough adhesive to the panels.



6.

After welding the No.4 pillar, rear seat gusset, center door pillar gusset rear, lower rail plate inner No.4, stiffener bracket No.5, pillar to rail gusset No.1, quarter panel palte upper No.1, center body pillar reinforce sub-assembly lower rear and center door piller dust proof plate rear to the vehicle side, install the *b.

7.

After welding, apply body sealer and undercoating to the corresponding parts. (See the painting / coating)

8.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.


INSTALLATION POINT (for Folding Type)
1.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.

2.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)

3.

Before installing a new part, apply body sealer.

HINT:

Apply body sealer in an even, continuous bead.


4.

Before temporarily installing the new parts, weld the No.4 pillar, rear seat gusset, center door pillar gusset rear, center door opening panel lower inner rear, stiffener bracket No.5, pillar to rail gusset No.1 and center body pillar plate outer with the standard number of welding points.

5.

Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115) to the area indicated by *a in the illustration.

HINT:
·

Apply a light coat of adhesive around the plug welding points.

·

Apply enough adhesive to the panels.



6.

After welding the No.4 pillar, rear seat gusset, center door pillar gusset rear, center door opening panel lower inner rear, stiffener bracket No.5, pillar to rail gusset No.1 and center body pillar plate outer to the vehicle side, install the *b.

7.

After welding, apply body sealer and undercoating to the corresponding parts. (See the painting / coating)

8.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.


K146216C01
4.594,1.135 4.521,0.208 4.521,0.208 4.708,0.208 false 3.813,2.802 4.604,2.396 4.604,2.396 4.844,2.396 false 4.771,4.729 4.51,4.729 4.51,4.729 4.875,3.969 false 4.656,7.26 4.438,7.26 4.438,7.26 3.813,6.604 false 3.396,0.865 3.125,0.458 3.125,0.458 2.896,0.458 false 3.677,2.115 3.115,1.073 3.115,1.073 2.917,1.073 false 3.594,2.302 2.917,1.833 2.917,1.833 2.75,1.833 false 3.333,5.948 2.656,5.479 2.656,5.479 2.49,5.479 false 3.385,7.875 2.708,7.406 2.708,7.406 2.542,7.406 false 0.188,0.229 0.5,0.385 0.313,0.156 10 false *A 2.75,0.406 3.063,0.563 0.313,0.156 10 false *1 2.76,1.021 3.073,1.177 0.313,0.156 10 false *2 4.885,2.354 5.198,2.51 0.313,0.156 10 false *3 4.813,4.667 5.125,4.823 0.313,0.156 10 false *4 4.74,0.167 5.052,0.323 0.313,0.156 10 false *5 2.583,1.771 2.896,1.927 0.313,0.156 10 false *6 2.323,5.427 2.635,5.583 0.313,0.156 10 false *7 4.698,7.208 5.01,7.365 0.313,0.156 10 false *8 2.365,7.354 2.677,7.51 0.313,0.156 10 false *9
*A for Glide Type - -
*1 NO.4 PILLAR *2 REAR SEAT GUSSET
*3 CENTER DOOR PILLAR GUSSET REAR *4 LOWER RAIL PLATE INNER NO.4
*5 STIFFENER BRACKET NO.5 *6 PILLAR TO RAIL GUSSET NO.1
*7 QUARTER PANEL PALTE UPPER NO.1 *8 CENTER BODY PILLAR REINFORCE SUB-ASSEMBLY LOWER REAR
*9 CENTER DOOR PILLER DUST PROOF PLATE REAR - -


K146217C01
0.26,0.219 0.573,0.375 0.313,0.156 10 false *A
*A for Glide Type - -


K146218C02
3.104,5.469 2.958,5.469 2.958,5.469 2.844,4.938 false 4.99,4.188 4.823,4.188 4.823,4.188 4.396,3.229 false 0.219,0.26 0.531,0.417 0.313,0.156 10 false *A 5.021,4.115 5.333,4.271 0.313,0.156 10 false *b 3.125,5.417 3.438,5.573 0.313,0.156 10 false *a
*A for Glide Type - -


K146219C01
3.396,0.531 3.135,0.302 3.135,0.302 2.969,0.302 false 3.635,1.688 3.073,0.844 3.073,0.844 2.906,0.844 false 3.573,1.948 2.938,1.49 2.938,1.49 2.75,1.49 false 4.531,0.865 5.188,0.125 5.188,0.125 5.427,0.125 false 3.781,2.5 4.49,2.188 4.49,2.188 4.667,2.188 false 2.302,5.156 2.51,5.156 2.51,5.156 2.417,4.51 false 4.188,7.74 4.042,7.74 4.042,7.74 3.542,7.115 false 0.24,0.208 0.552,0.365 0.313,0.156 10 false *A 2.802,0.229 3.115,0.385 0.313,0.156 10 false *1 2.75,0.771 3.063,0.927 0.313,0.156 10 false *2 4.698,2.125 5.01,2.281 0.313,0.156 10 false *3 2.135,5.094 2.448,5.25 0.313,0.156 10 false *4 5.448,0.094 5.76,0.25 0.313,0.156 10 false *5 2.604,1.427 2.917,1.583 0.313,0.156 10 false *6 4.219,7.688 4.531,7.844 0.313,0.156 10 false *7
*A for Folding Type - -
*1 NO.4 PILLAR *2 REAR SEAT GUSSET
*3 CENTER DOOR PILLAR GUSSET REAR *4 CENTER DOOR OPENING PANEL LOWER INNER REAR
*5 STIFFENER BRACKET NO.5 *6 PILLAR TO RAIL GUSSET NO.1
*7 CENTER BODY PILLAR PLATE OUTER - -


K147978C02
1.677,2.073 2.083,1.625 false 1.896,2.021 2.094,1.625 false 1.677,2.167 2.083,1.625 2.083,1.625 2.24,1.625 false 0.125,0.146 0.438,0.365 0.313,0.219 10 false *A 2.292,1.563 2.604,1.76 0.313,0.198 10 false *a
*A for Folding Type - -


K146222C02
3.25,5.438 3.083,5.438 3.083,5.438 2.99,4.927 false 4.823,4.469 4.646,4.469 4.646,4.469 4.281,3.458 false 0.229,0.292 0.542,0.448 0.313,0.156 10 false *A 4.875,4.406 5.188,4.604 0.313,0.198 10 false *b 3.281,5.365 3.594,5.563 0.313,0.198 10 false *a
*A for Folding Type - -