Home › Vehicle Exterior › BODY PANEL › CENTER DOOR RAIL LOWER INNER(for RHD)
BM2850E _01 Vehicle Exterior _075893 BODY PANEL _0369069 CENTER DOOR RAIL LOWER INNER(for RHD) F

BODY PANEL  CENTER DOOR RAIL LOWER INNER(for RHD)  ASSEMBLY REPLACEMENT  


K139854

With the center door rail lower outer, No.3 pillar and No.4 pillar removed. (for Gliding Type)

With the No.3 pillar and No.4 pillar removed. (for Folding Type)


REMOVAL


Symbol Meaning
K108818

Remove Weld Points
K108820

Remove Weld Points


REMOVAL POINT
1.

*a in illustration above indicates where the adhesive is located.

2.

Roughly cut open the panel so that the adhesive can be reached. Cut through the adhesive with a cut chisel to remove the panel.

HINT:

In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.



K146225C02
2.635,5.375 3.354,4.813 3.354,4.813 3.625,4.813 false 4.396,5.375 3.354,4.813 false 3.667,4.74 3.979,4.938 0.313,0.198 10 false *a 0.292,0.198 0.604,0.396 0.313,0.198 10 false *A
*A for Glide Type - -


K146226C01
0.281,0.271 0.594,0.469 0.313,0.198 10 false *A
*A for Glide Type - -


K146229C01
2.594,5.417 3.292,4.813 3.292,4.813 3.458,4.813 false 3.281,4.813 4.5,5.406 false 3.51,4.74 3.823,4.938 0.313,0.198 10 false *a 0.313,0.354 0.625,0.51 0.313,0.156 10 false *A
*A for Folding Type - -


K146230C01
0.271,0.292 0.583,0.448 0.313,0.156 10 false *A
*A for Folding Type - -


INSTALLATION


Symbol Meaning
K108823

Plug Weld
K108825

Plug Weld
K108834

Body Sealer


INSTALLATION POINT
1.

Before installing a new part, apply body sealer.

HINT:

Apply body sealer in an even, continuous bead.


2.

Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115) to the area indicated by *a in the illustration.

HINT:
·

Apply a light coat of adhesive around the plug welding points.

·

Apply enough adhesive to the panels.



3.

After welding, apply body sealer and undercoating to the corresponding parts. (See the painting /coating)

4.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.


K146227C02
2.375,2.406 2.469,0.833 2.469,0.833 2.677,0.833 false 4.573,2.375 4.667,0.802 4.667,0.802 4.875,0.802 false 3.469,3.646 3.719,4.083 3.719,4.083 3.875,4.083 false 2.635,5.833 3.375,5.25 3.375,5.25 3.531,5.25 false 4.385,5.813 3.375,5.26 false 2.74,0.781 3.052,0.938 0.313,0.156 10 false *1 4.906,0.75 5.219,0.906 0.313,0.156 10 false *2 3.906,4.031 4.219,4.188 0.313,0.156 10 false *3 3.583,5.198 3.896,5.396 0.313,0.198 10 false *a 0.271,0.219 0.604,0.469 0.333,0.25 10 false *A
*A for Glide Type - -
*1 NO.3 INNER PILLAR LOWER *2 NO.4 INNER PILLAR LOWER
*3 NO.7 LOWER INNER RAIL SUB-ASSEMBLY LOWER - -


K146228C01
0.25,0.271 0.563,0.469 0.313,0.198 10 false *A
*A for Glide Type - -


K146233C01
2.365,2.427 2.479,0.927 2.479,0.927 2.625,0.927 false 4.573,2.396 4.688,0.896 4.688,0.896 4.833,0.896 false 4.146,4.25 3.969,4.25 3.969,4.25 3.74,3.646 false 2.604,5.813 3.417,6.281 3.417,6.281 3.604,6.281 false 3.417,6.271 4.49,5.813 false 0.26,0.219 0.573,0.375 0.313,0.156 10 false *A 2.667,0.875 2.979,1.031 0.313,0.156 10 false *1 4.875,0.854 5.188,1.01 0.313,0.156 10 false *2 4.177,4.188 4.49,4.344 0.313,0.156 10 false *3 3.635,6.219 3.948,6.375 0.313,0.156 10 false *a
*A for Folding Type - -
*1 NO.3 INNER PILLAR LOWER *2 NO.4 INNER PILLAR LOWER
*3 NO.7 LOWER INNER RAIL SUB-ASSEMBLY LOWER - -


K146234C01
4.281,7.958 4.125,7.958 4.125,7.958 3.906,7.135 false 0.24,0.271 0.552,0.427 0.313,0.156 10 false *A 4.323,7.896 4.635,8.052 0.313,0.156 10 false *1
*A for Folding Type - -
*1 CENTER DOOR RAIL LOWER OUTER - -