Home › Vehicle Exterior › BODY PANEL › ROOF PANEL NO.4 › 2017.01–2019.08
BM2850E _01 Vehicle Exterior _075893 BODY PANEL _0369078 ROOF PANEL NO.4 F

BODY PANEL  ROOF PANEL NO.4  CUT AND JOIN REPLACEMENT SECTIONS  


K140020

With the roof panel No.1 removed.


HINT:

w/ ROOF SIDE REINFORCEMENT (See the 2019/08-)


REMOVAL


Symbol Meaning
K108818

Remove Weld Points
K108827

Cut and Join Location
K108828

Cut Location for Supply Parts


K146281C02
4.146,4.948 4.729,5.25 0.583,0.302 10 false 90 (3.54) 2.563,5.24 3.271,5.531 0.708,0.292 10 false 235 (9.25) 0.198,0.177 0.51,0.333 0.313,0.156 10 false *A 1.208,1.073 1.521,1.229 0.313,0.156 10 false *1 3.292,1.083 3.604,1.24 0.313,0.156 10 false *2 5.729,1.104 6.042,1.26 0.313,0.156 10 false *3 0.167,8.604 0.479,8.802 0.313,0.198 10 false *a
*A LH - -
*1 Rough Cut Panel *2 Grind
*3 After Removing - -
*a mm (in.) - -


K146282C01
0.26,0.271 0.573,0.427 0.313,0.156 10 false *A
*A LH - -


K146283C01
0.229,0.188 0.542,0.344 0.313,0.156 10 false *A 1.188,1.021 1.5,1.177 0.313,0.156 10 false *1 3.531,1.052 3.844,1.208 0.313,0.156 10 false *2 5.729,1.042 6.042,1.198 0.313,0.156 10 false *3
*A RH - -
*1 Rough Cut Panel *2 Grind
*3 After Removing - -


K146284C01
0.281,0.292 0.594,0.448 0.313,0.156 10 false *A
*A RH - -


INSTALLATION


Symbol Meaning
K108823

Plug Weld
K108825

Plug Weld
K108831

Butt Weld


INSTALLATION POINT
1.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.

2.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)

3.

Follow the welding conditions when welding *a to assure sufficient weld strength.

Plug Diameter Welding Wire Diameter Plug Welding Hole Pitch Shield Gas
4 mm (0.16 in.) 0.6 mm (0.02 in.) 25 mm (0.98 in.) Metal active gas (Ar 80% + CO2 20%))
5 mm (0.20 in.) 0.8 mm (0.03 in.) 30mm (1.18 in.)

4.

After welding, apply body sealer to the corresponding parts. (See the painting / coating)

5.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.


K146285C02
3.563,5.646 3.438,5.115 3.438,5.115 3.219,5.115 false 1.438,0.302 1.271,0.302 1.271,0.302 1.51,1.177 false 0.302,0.24 0.615,0.396 0.313,0.156 10 false *A 3.042,5.063 3.354,5.219 0.313,0.156 10 false *2 0.177,8.604 0.49,8.76 0.313,0.156 10 false *b 3.781,5.646 4.563,5.854 0.781,0.208 10 false 3.7 (0.15) 2.625,6.448 3.375,6.656 0.75,0.208 10 false 11.8 (0.46) 4.875,0.979 5.188,1.177 0.313,0.198 10 false *a 5.271,2.146 5.583,2.344 0.313,0.198 10 false *a 1.479,0.219 1.792,0.375 0.313,0.156 10 false *1
*A LH - -
*1 FRONT BODY PILLAR UPPER OUTER *2 Plug Welding Hole Center
*b mm (in.) - -


K146286C01
0.198,0.208 0.51,0.365 0.313,0.156 10 false *A
*A LH - -


K146287C02
3.552,5.646 3.74,5.229 3.74,5.229 3.906,5.229 false 5.563,1.125 6.198,0.26 6.198,0.26 5.979,0.26 false 0.104,0.135 0.417,0.292 0.313,0.156 10 false *A 5.833,0.198 6.146,0.354 0.313,0.156 10 false *1 0.167,8.583 0.479,8.74 0.313,0.156 10 false *b 2.01,0.844 2.323,1 0.313,0.156 11 false *a 1.135,2.156 1.448,2.313 0.313,0.156 10 false *a 3.948,5.177 4.26,5.333 0.313,0.156 10 false *2 2.74,5.635 3.396,5.833 0.656,0.198 10 false 3.7 (0.15) 3.875,6.479 4.583,6.729 0.708,0.25 10 false 11.8 (0.46)
*A RH - -
*1 FRONT BODY PILLAR UPPER OUTER *2 Plug Welding Hole Center
*b mm (in.) - -


K146288C01
0.177,0.271 0.49,0.427 0.313,0.156 10 false *A
*A RH - -