for Standard Body (for Rigid Mount)
Upper Face
Length measurements are indicated at the points where the arrows extending from the zero point intersect the lines that extend towards the outside of the illustration from each point.
In cases in which only one dimension is given, left and right are symmetrical.
For symbols, capital letters indicate right side of vehicle, small letters indicate left side of vehicle (seen from rear).
| Symbol | Name | Hole Diameter
mm (in.) |
|---|---|---|
| A, a | Body Mounting Hole | φ13 (0.51) |
| B, b | Shock Absorber Installation Hole | φ23.6 (0.93) |
| C, c | Body Mounting Hole | 18X16
(0.71X0.63) |
| D, d | Body Mounting Hole | 18X16
(0.71X0.63) |
| E, e | Body Mounting Hole | 18X16
(0.71X0.63) |
| F, f | Body Mounting Hole | 18X16
(0.71X0.63) |
| G, g | Body Mounting Hole | 18X16
(0.71X0.63) |
| H, h | Body Mounting Hole | 13X11
(0.51X0.43) |
| Wheel Base | 3200 mm (125.98 in.) |
| *A | LH | *B | RH |
| *C | Front | - | - |
| *a | mm
(in.) |
- | - |
| *a | Imaginary Datum Line | *b | Height from Imaginary Datum Line |
| *c | mm
(in.) |
- | - |
Lower Face
Length measurements are indicated at the points where the arrows extending from the zero point intersect the lines that extend towards the outside of the illustration from each point.
In cases in which only one dimension is given, left and right are symmetrical.
For symbols, capital letters indicate right side of vehicle, small letters indicate left side of vehicle (seen from rear).
| Symbol | Name | Hole Diameter
mm (in.) |
|---|---|---|
| A, a | Engine Under Cover Bracket Installation Nut | M8 (0.31) |
| B, b | Suspension Lower Arm Installation Hole | 40X18.5
(1.57X0.73) |
| C, c | Suspension Lower Arm Installation Hole | 40X18.5
(1.57X0.73) |
| D, d | Crossmember No. 4 Installation Hole | φ11 (0.43) |
| E, e | Rear Spring Front Shackle Hole | φ16 (0.63) |
| F, f | Bumper Stopper Installation Hole | φ11 (0.43) |
| G, g | Rear Spring Rear Shackle Hole | φ40 (1.57) |
| H, h | Side Rail Standard Hole | φ13 (0.51) |
| Wheel Base | 3200 mm (125.98 in.) |
| *A | LH | *B | RH |
| *C | Front | - | - |
| *a | mm
(in.) |
- | - |
| *a | Imaginary Datum Line | *b | Height from Imaginary Datum Line |
| *c | mm
(in.) |
- | - |
for Standard Body (for Rubber Mount)
Upper Face
Length measurements are indicated at the points where the arrows extending from the zero point intersect the lines that extend towards the outside of the illustration from each point.
In cases in which only one dimension is given, left and right are symmetrical.
For symbols, capital letters indicate right side of vehicle, small letters indicate left side of vehicle (seen from rear).
| Symbol | Name | Hole Diameter
mm (in.) |
|---|---|---|
| A, a | Body Mounting Hole | φ13 (0.51) |
| B, b | Shock Absorber Installation Hole | φ23.6 (0.93) |
| C, c | Body Mounting Hole | 18X16
(0.71X0.63) |
| D, d | Body Mounting Hole | 18X16
(0.71X0.63) |
| E, e | Body Mounting Hole | 18X16
(0.71X0.63) |
| F, f | Body Mounting Hole | φ51 (2.01) |
| G, g | Body Mounting Hole | φ51 (2.01) |
| H, h | Body Mounting Hole | φ51 (2.01) |
| J, j | Body Mounting Hole | φ51 (2.01) |
| K, k | Body Mounting Hole | φ51 (2.01) |
| Wheel Base | 3200 mm (125.98 in.) |
| *A | LH | *B | RH |
| *C | Front | - | - |
| *a | mm
(in.) |
- | - |
| *a | Imaginary Datum Line | *b | Distance between points other than those above |
| *c | mm
(in.) |
- | - |
Lower Face
Length measurements are indicated at the points where the arrows extending from the zero point intersect the lines that extend towards the outside of the illustration from each point.
In cases in which only one dimension is given, left and right are symmetrical.
For symbols, capital letters indicate right side of vehicle, small letters indicate left side of vehicle (seen from rear).
| Symbol | Name | Hole Diameter
mm (in.) |
|---|---|---|
| A, a | Engine Under Cover Bracket Installation Nut | M8 (0.31) |
| B, b | Suspension Lower Arm Installation Hole | 40X18.5
(1.57X0.73) |
| C, c | Suspension Lower Arm Installation Hole | 40X18.5
(1.57X0.73) |
| D, d | Crossmember No. 4 Installation Hole | φ11 (0.43) |
| E, e | Rear Spring Front Shackle Hole | φ16 (0.63) |
| F, f | Bumper Stopper Installation Hole | φ11 (0.43) |
| G, g | Rear Spring Rear Shackle Hole | φ40 (1.57) |
| H, h | Side Rail Standard Hole | φ13 (0.51) |
| Wheel Base | 3200 mm (125.98 in.) |
| *A | LH | *B | RH |
| *C | Front | - | - |
| *a | mm
(in.) |
- | - |
| *a | Imaginary Datum Line | *b | Distance between points other than those above |
| *c | mm
(in.) |
- | - |
for Long Body (for Rigid Mount)
exept LPG
Upper Face
Length measurements are indicated at the points where the arrows extending from the zero point intersect the lines that extend towards the outside of the illustration from each point.
In cases in which only one dimension is given, left and right are symmetrical.
For symbols, capital letters indicate right side of vehicle, small letters indicate left side of vehicle (seen from rear).
| Symbol | Name | Hole Diameter
mm (in.) |
|---|---|---|
| A, a | Body Mounting Hole | φ13 (0.51) |
| B, b | Shock Absorber Installation Hole | φ23.6 (0.93) |
| C, c | Body Mounting Hole | 18X16
(0.71X0.63) |
| D, d | Body Mounting Hole | 18X16
(0.71X0.63) |
| E, e | Body Mounting Hole | 18X16
(0.71X0.63) |
| F, f | Body Mounting Hole | 18X16
(0.71X0.63) |
| G, g | Body Mounting Hole | 18X16
(0.71X0.63) |
| H, h | Body Mounting Hole | 18X16
(0.71X0.63) |
| J, j | Body Mounting Hole | 13X11
(0.51X0.43) |
| Wheel Base | 3935 mm (154.92 in.) |
| *A | LH | *B | RH |
| *C | Front | - | - |
| *a | mm
(in.) |
- | - |
| *a | Imaginary Datum Line | *b | Height from Imaginary Datum Line |
| *c | mm
(in.) |
- | - |
Lower Face
Length measurements are indicated at the points where the arrows extending from the zero point intersect the lines that extend towards the outside of the illustration from each point.
In cases in which only one dimension is given, left and right are symmetrical.
For symbols, capital letters indicate right side of vehicle, small letters indicate left side of vehicle (seen from rear).
| Symbol | Name | Hole Diameter
mm (in.) |
|---|---|---|
| A, a | Engine Under Cover Bracket Installation Nut | M8 (0.31) |
| B, b | Suspension Lower Arm Installation Hole | 40X18.5
(1.57X0.73) |
| C, c | Suspension Lower Arm Installation Hole | 40X18.5
(1.57X0.73) |
| D, d | Crossmember No. 4 Installation Hole | φ11 (0.43) |
| E, e | Crossmember No. 5 Installation Hole | φ11 (0.43) |
| F, f | Rear Spring Front Shackle Hole | φ16 (0.63) |
| G, g | Bumper Stopper Installation Hole | φ11 (0.43) |
| H, h | Rear Spring Rear Shackle Hole | φ40 (1.57) |
| J, j | Side Rail Standard Hole | φ13 (0.51) |
| Wheel Base | 3935 mm (154.92 in.) |
| *A | LH | *B | RH |
| *C | Front | - | - |
| *a | mm
(in.) |
- | - |
| *a | Imaginary Datum Line | *b | Height from Imaginary Datum Line |
| *c | mm
(in.) |
- | - |
for LPG
Upper Face
Point F, f, on the vehicle are asymmetrical.
Length measurements are indicated at the points where the arrows extending from the zero point intersect the lines that extend towards the outside of the illustration from each point.
In cases in which only one dimension is given, left and right are symmetrical.
For symbols, capital letters indicate right side of vehicle, small letters indicate left side of vehicle (seen from rear).
| Symbol | Name | Hole Diameter
mm (in.) |
|---|---|---|
| A, a | Body Mounting Hole | φ13 (0.51) |
| B, b | Shock Absorber Installation Hole | φ23.6 (0.93) |
| C, c | Body Mounting Hole | 18X16
(0.71X0.63) |
| D | Body Mounting Nut | M10 (0.39) |
| d | Body Mounting Hole | 18X16
(0.71X0.63) |
| E | Body Mounting Nut | M10 (0.39) |
| e | Body Mounting Hole | 18X16
(0.71X0.63) |
| F, f | Body Mounting Hole | 18X16
(0.71X0.63) |
| G, g | Body Mounting Hole | 18X16
(0.71X0.63) |
| H, h | Body Mounting Hole | 18X16
(0.71X0.63) |
| J, j | Body Mounting Hole | 13X11
(0.51X0.43) |
| Wheel Base | 3935 mm (154.92 in.) |
| *A | LH | *B | RH |
| *C | Front | - | - |
| *a | mm
(in.) |
- | - |
| *a | Imaginary Datum Line | *b | Height from Imaginary Datum Line |
| *c | mm
(in.) |
- | - |
Lower Face
Length measurements are indicated at the points where the arrows extending from the zero point intersect the lines that extend towards the outside of the illustration from each point.
In cases in which only one dimension is given, left and right are symmetrical.
For symbols, capital letters indicate right side of vehicle, small letters indicate left side of vehicle (seen from rear).
| Symbol | Name | Hole Diameter
mm (in.) |
|---|---|---|
| A, a | Engine Under Cover Bracket Installation Nut | M8 (0.31) |
| B, b | Suspension Lower Arm Installation Hole | 40X18.5
(1.57X0.73) |
| C, c | Suspension Lower Arm Installation Hole | 40X18.5
(1.57X0.73) |
| D, d | Crossmember No. 4 Installation Hole | φ11 (0.43) |
| E, e | Crossmember No. 5 Installation Hole | φ11 (0.43) |
| F, f | Rear Spring Front Shackle Hole | φ16 (0.63) |
| G, g | Bumper Stopper Installation Hole | φ11 (0.43) |
| H, h | Rear Spring Rear Shackle Hole | φ40 (1.57) |
| J, j | Side Rail Standard Hole | φ13 (0.51) |
| Wheel Base | 3935 mm (154.92 in.) |
| *A | LH | *B | RH |
| *C | Front | - | - |
| *a | mm
(in.) |
- | - |
| *a | Imaginary Datum Line | *b | Height from Imaginary Datum Line |
| *c | mm
(in.) |
- | - |
for Long Body (for Rubber Mount)
Upper Face
Length measurements are indicated at the points where the arrows extending from the zero point intersect the lines that extend towards the outside of the illustration from each point.
In cases in which only one dimension is given, left and right are symmetrical.
For symbols, capital letters indicate right side of vehicle, small letters indicate left side of vehicle (seen from rear).
| Symbol | Name | Hole Diameter
mm (in.) |
|---|---|---|
| A, a | Body Mounting Hole | φ13 (0.51) |
| B, b | Shock Absorber Installation Hole | φ23.6 (0.93) |
| C, c | Body Mounting Hole | 18X16
(0.71X0.63) |
| D, d | Body Mounting Hole | 18X16
(0.71X0.63) |
| E, e | Body Mounting Hole | 18X16
(0.71X0.63) |
| F, f | Body Mounting Hole | 18X16
(0.71X0.63) |
| G, g | Body Mounting Hole | φ51 (2.01) |
| H, h | Body Mounting Hole | φ51 (2.01) |
| J, j | Body Mounting Hole | φ51 (2.01) |
| K, k | Body Mounting Hole | φ51 (2.01) |
| L, l | Body Mounting Hole | φ51 (2.01) |
| Wheel Base | 3935 mm (154.92 in.) |
| *A | LH | *B | RH |
| *C | Front | - | - |
| *a | mm
(in.) |
- | - |
| *a | Imaginary Datum Line | *b | Height from Imaginary Datum Line |
| *c | mm
(in.) |
- | - |
Lower Face
Length measurements are indicated at the points where the arrows extending from the zero point intersect the lines that extend towards the outside of the illustration from each point.
In cases in which only one dimension is given, left and right are symmetrical.
For symbols, capital letters indicate right side of vehicle, small letters indicate left side of vehicle (seen from rear).
| Symbol | Name | Hole Diameter
mm (in.) |
|---|---|---|
| A, a | Engine Under Cover Bracket Installation Nut | M8 (0.31) |
| B, b | Suspension Lower Arm Installation Hole | 40X18.5
(1.57X0.73) |
| C, c | Suspension Lower Arm Installation Hole | 40X18.5
(1.57X0.73) |
| D, d | Crossmember No. 4 Installation Hole | φ11 (0.43) |
| E, e | Crossmember No. 5 Installation Hole | φ11 (0.43) |
| F, f | Rear Spring Front Shackle Hole | φ16 (0.63) |
| G, g | Bumper Stopper Installation Hole | φ11 (0.43) |
| H, h | Rear Spring Rear Shackle Hole | φ40 (1.57) |
| J, j | Side Rail Standard Hole | φ13 (0.51) |
| Wheel Base | 3935 mm (154.92 in.) |
| *A | LH | *B | RH |
| *C | Front | - | - |
| *a | mm
(in.) |
- | - |
| *a | Imaginary Datum Line | *b | Height from Imaginary Datum Line |
| *c | mm
(in.) |
- | - |
for Super Long Body
Upper Face
Length measurements are indicated at the points where the arrows extending from the zero point intersect the lines that extend towards the outside of the illustration from each point.
In cases in which only one dimension is given, left and right are symmetrical.
For symbols, capital letters indicate right side of vehicle, small letters indicate left side of vehicle (seen from rear).
| Symbol | Name | Hole Diameter
mm (in.) |
|---|---|---|
| A, a | Body Mounting Hole | φ13 (0.51) |
| B, b | Shock Absorber Installation Hole | φ23.6 (0.93) |
| C, c | Body Mounting Hole | 18X16
(0.71X0.63) |
| D, d | Body Mounting Hole | 18X16
(0.71X0.63) |
| E, e | Body Mounting Hole | 18X16
(0.71X0.63) |
| F, f | Body Mounting Hole | 18X16
(0.71X0.63) |
| G, g | Body Mounting Hole | 18X16
(0.71X0.63) |
| H, h | Body Mounting Hole | 18X16
(0.71X0.63) |
| J, j | Body Mounting Hole | 18X16
(0.71X0.63) |
| K, k | Body Mounting Hole | 13X11
(0.51X0.43) |
| Wheel Base | 4435 mm (174.61 in.) |
| *A | LH | *B | RH |
| *C | Front | - | - |
| *a | mm
(in.) |
- | - |
| *a | Imaginary Datum Line | *b | Height from Imaginary Datum Line |
| *c | mm
(in.) |
- | - |
Lower Face
Length measurements are indicated at the points where the arrows extending from the zero point intersect the lines that extend towards the outside of the illustration from each point.
In cases in which only one dimension is given, left and right are symmetrical.
For symbols, capital letters indicate right side of vehicle, small letters indicate left side of vehicle (seen from rear).
| Symbol | Name | Hole Diameter
mm (in.) |
|---|---|---|
| A, a | Engine Under Cover Bracket Installation Nut | M8 (0.31) |
| B, b | Suspension Lower Arm Installation Hole | 40X18.5
(1.57X0.73) |
| C, c | Suspension Lower Arm Installation Hole | 40X18.5
(1.57X0.73) |
| D, d | Crossmember No. 4 Installation Hole | φ11 (0.43) |
| E, e | Crossmember No. 5 Installation Hole | φ11 (0.43) |
| F, f | Rear Spring Front Shackle Hole | φ16 (0.63) |
| G, g | Bumper Stopper Installation Hole | φ11 (0.43) |
| H, h | Rear Spring Rear Shackle Hole | φ40 (1.57) |
| J, j | Side Rail Standard Hole | φ13 (0.51) |
| Wheel Base | 4435 mm (174.61 in.) |
| *A | LH | *B | RH |
| *C | Front | - | - |
| *a | mm
(in.) |
- | - |
| *a | Imaginary Datum Line | *b | Height from Imaginary Datum Line |
| *c | mm
(in.) |
- | - |