Home › Vehicle Exterior › BODY PANEL › SIDE PANEL NO.1 LH (for LHD) › from 2019.08
BM2850E _01 Vehicle Exterior _075893 BODY PANEL _0369057 SIDE PANEL NO.1 LH(for LHD) F

BODY PANEL  SIDE PANEL NO.1 LH(for LHD)  ASSEMBLY REPLACEMENT  


K139980

REMOVAL



Symbol Meaning
K108818

Remove Weld Points
K108827

Cut and Join Location

REMOVAL POINT
1.

*a in illustration above indicates where the adhesive is located.

2.

Roughly cut open the panel so that the adhesive can be reached. Cut through the adhesive with a cut chisel to remove the panel.

HINT:

In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.



K150201C01
3.448,7.854 2.115,6.781 false 3.438,7.823 2.5,6.792 false 3.448,7.844 2.927,6.771 false 3.448,7.833 3.219,6.781 false 3.448,7.844 3.542,6.781 false 3.448,7.844 3.708,6.781 false 3.448,7.854 3.885,6.781 false 3.188,7.854 3.438,7.854 false 3.708,0.948 4.479,1.167 0.771,0.219 10 false 130 (5.12) 3.031,7.76 3.229,7.969 0.198,0.208 10 false *a 0.219,8.51 0.573,8.719 0.354,0.208 10 false *b
*b mm (in.) - -


K147914

INSTALLATION


Symbol Meaning
K108823

Plug Weld
K108827

Cut and Join Location
K108830

Fillet Weld
K108831

Butt Weld
K108834

Body Sealer


INSTALLATION POINT
1.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.

2.

*a Dent one part about 1 to 2 mm (0.04 to 0.08 in.) .

3.

Before temporarily installing the new parts, weld the front side panel outer and mudguard bracket front with the standard number of welding points.

4.

Before installing a new part, apply body sealer.

HINT:
·

Apply body sealer evenly about 5 mm (0.20 in.) from the flange, avoiding any oozing.

·

Apply body sealer evenly, about 3 to 4 mm (0.12 to 0.16 in.) in diameter.



5.

Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115) to the area indicated by *b in the illustration.

HINT:
·

Apply a light coat of adhesive around the plug welding points.

·

Apply enough adhesive to the panels.



6.

After welding, apply body sealer to the corresponding parts. (See the painting / coating)

7.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.


K150202C01
4.365,7.688 5.083,7 5.083,7 5.25,7 false 4.365,8.479 5.083,7 false 0.333,8.375 0.646,8.573 0.313,0.198 10 false *c 5.313,6.896 5.625,7.094 0.313,0.198 10 false *a 2.906,0.219 3.573,0.458 0.667,0.24 10 false 15 (0.59) 2.042,1.417 2.708,1.656 0.667,0.24 10 false 15 (0.59) 5.813,2.094 6.479,2.333 0.667,0.24 10 false 15 (0.59) 4.823,2.719 5.49,2.958 0.667,0.24 10 false 15 (0.59) 4.979,3.833 5.646,4.073 0.667,0.24 10 false 15 (0.59) 1.969,5.615 2.635,5.854 0.667,0.24 10 false 15 (0.59) 2.99,6.26 3.656,6.5 0.667,0.24 10 false 15 (0.59)
*c mm (in.) - -


K147916C01
2.719,5.104 2.365,5.969 2.365,5.969 2.531,5.969 false 3.115,1.813 2.948,1.813 2.948,1.813 3.01,2.573 false 3.146,1.729 3.458,1.927 0.313,0.198 10 false *1 2.583,5.885 2.896,6.083 0.313,0.198 10 false *2
*1 FRONT SIDE PANEL OUTER *2 MUDGUARD BRACKET FRONT


K150203C01
2.552,4.448 3.667,5.5 3.667,5.5 3.833,5.5 false 3.677,5.5 2.948,4.448 false 3.667,5.49 3.344,4.448 false 3.667,5.49 3.688,4.448 false 3.667,5.49 3.979,4.427 false 3.677,5.479 4.177,4.448 false 3.865,5.417 4.177,5.615 0.313,0.198 10 false *b 0.313,8.469 0.625,8.667 0.313,0.198 12 false *c 3.5,6.99 4.031,7.198 0.531,0.208 10 false 5 (0.20)
*c mm (in.) - -


K150204

K150205C01
1.927,6.479 2.094,6.479 2.094,6.479 3.448,7.052 false 1.042,7.698 1.208,7.698 1.208,7.698 1.49,7.51 false 3.219,8.01 3.385,8.01 3.385,8.01 3.604,8.344 false 4.646,7.135 4.969,6.823 4.969,6.823 5.135,6.823 false 4.25,6.667 5.219,6.417 5.219,6.417 5.385,6.417 false 5.208,7.531 5.396,7.74 5.396,7.74 5.563,7.74 false 4.365,8.396 4.635,8.031 4.635,8.031 4.802,8.031 false 1.417,7.125 1.583,7.125 1.583,7.125 1.802,7.458 false 1.771,6.417 2.083,6.615 0.313,0.198 10 false *1 4.896,3.646 5.49,3.875 0.594,0.229 10 false 5 (0.20) 5.01,5.333 5.604,5.563 0.594,0.229 10 false 5 (0.20) 3.052,7.917 3.365,8.115 0.313,0.198 10 false *2 0.875,7.604 1.188,7.802 0.313,0.198 10 false *3 5.177,6.74 5.49,6.938 0.313,0.198 10 false *5 5.427,6.333 5.74,6.531 0.313,0.198 10 false *4 5.594,7.656 5.906,7.854 0.313,0.198 10 false *6 4.844,7.948 5.156,8.146 0.313,0.198 10 false *5 0.104,8.615 0.417,8.813 0.313,0.198 10 false *c 1.198,8.146 1.51,8.344 0.313,0.198 10 false *7 1.25,7.052 1.563,7.25 0.313,0.198 10 false *2
*1 Plug Weld *2 Reference Surface
*3 New Panel *4 Fillet Weld
*5 Putty *6 Vehicle Side Panel
*7 Cross Section Illustration - -
*c mm (in.) - -


K147920