Home › Vehicle Exterior › BODY PANEL › SIDE PANEL NO.1 RH (for RHD) › from 2019.08
BM2850E _01 Vehicle Exterior _075893 BODY PANEL _0369108 SIDE PANEL NO.1 RH(for RHD) F

BODY PANEL  SIDE PANEL NO.1 RH(for RHD)  ASSEMBLY REPLACEMENT  


K139868

REMOVAL



Symbol Meaning
K108818

Remove Weld Points
K108827

Cut and Join Location

REMOVAL POINT
1.

*a in illustration above indicates where the adhesive is located.

2.

Roughly cut open the panel so that the adhesive can be reached. Cut through the adhesive with a cut chisel to remove the panel.

HINT:

In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.



K150206C01
4.031,6.76 4.75,7.75 4.75,7.75 4.917,7.75 false 4.75,7.75 4.208,6.76 false 4.75,7.75 4.417,6.75 false 4.75,7.75 4.667,6.75 false 4.75,7.75 5,6.75 false 4.75,7.75 5.5,6.75 false 4.75,7.75 5.833,6.75 false 0.729,5.917 1.042,6.115 0.313,0.198 10 false *A 0.302,8.396 0.615,8.594 0.313,0.198 10 false *b 5.083,7.688 5.396,7.885 0.313,0.198 10 false *a 2.115,0.927 2.802,1.156 0.688,0.229 10 false 130 (5.12)
*A for LPG - -
*b mm (in.) - -


K146131

INSTALLATION


Symbol Meaning
K108823

Plug Weld
K108827

Cut and Join Location
K108830

Fillet Weld
K108831

Butt Weld
K108834

Body Sealer


INSTALLATION POINT
1.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.

2.

*a Dent one part about 1 to 2 mm (0.04 to 0.08 in.) .

3.

Before temporarily installing the new parts, weld the front side panel outer and mudguard bracket front with the standard number of welding points.

4.

Before temporarily installing the new parts, weld the front side panel outer, mudguard bracket front and front body pillar lower hinge retainer with the standard number of welding points. (for LPG)

5.

Before installing a new part, apply body sealer.

HINT:
·

Apply body sealer evenly about 5 mm (0.20 in.) from the flange, avoiding any oozing.

·

Apply body sealer evenly, about 3 to 4 mm (0.12 to 0.16 in.) in diameter.



6.

Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115) to the area indicated by *b in the illustration.

HINT:
·

Apply a light coat of adhesive around the plug welding points.

·

Apply enough adhesive to the panels.



7.

After welding, apply body sealer to the corresponding parts. (See the painting / coating)

8.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.


K150187C02
2.083,7.083 2.948,7.792 false 1.927,7.083 2.083,7.083 2.083,7.083 2.948,8.563 false 0.208,8.531 0.49,8.677 0.281,0.146 10 false *c 1.677,6.99 1.958,7.135 0.281,0.146 10 false *a 3.854,0.313 4.542,0.51 0.688,0.198 10 false 15 (0.59) 4.708,1.531 5.396,1.729 0.688,0.198 10 false 15 (0.59) 1.01,2.188 1.698,2.385 0.688,0.198 10 false 15 (0.59) 2,2.844 2.688,3.042 0.688,0.198 10 false 15 (0.59) 1.844,3.948 2.531,4.146 0.688,0.198 10 false 15 (0.59) 4.833,5.74 5.521,5.938 0.688,0.198 10 false 15 (0.59) 3.698,6.375 4.385,6.573 0.688,0.198 10 false 15 (0.59)
*c mm (in.) - -


K147930C01
3,0.854 3.031,0.313 3.031,0.313 3.198,0.313 false 4.417,3.042 4.646,3.406 4.646,3.406 4.813,3.406 false 2.542,6.906 1.979,7.406 1.979,7.406 2.146,7.406 false 3.25,0.219 3.563,0.417 0.313,0.198 10 false *1 4.823,3.313 5.135,3.51 0.313,0.198 10 false *2 0.448,4.031 0.76,4.229 0.313,0.198 10 false *A 2.198,7.313 2.51,7.51 0.313,0.198 10 false *3
*1 FRONT SIDE PANEL OUTER *2 MUDGUARD BRACKET FRONT
*3 FRONT BODY PILLAR LOWER HINGE RETAINER - -
*A for LPG - -


K150207C01
4.885,5.75 4.75,5.75 4.75,5.75 4.25,4.75 false 4.75,5.75 4.438,4.75 false 4.75,5.75 4.771,4.75 false 4.75,5.75 5.083,4.75 false 4.75,5.75 5.5,4.75 false 4.75,5.75 5.854,4.75 false 4.99,5.667 5.302,5.865 0.313,0.198 10 false *b 0.74,3.885 1.052,4.083 0.313,0.198 10 false *A 2.958,7.281 3.563,7.521 0.604,0.24 10 false 5 (0.20) 0.302,8.438 0.615,8.635 0.313,0.198 10 false *c
*A for LPG - -
*c mm (in.) - -


K150189

K150190C02
3.604,7.302 4.896,6.677 4.896,6.677 5.104,6.677 false 5.531,7.688 5.896,7.167 5.896,7.167 6.073,7.167 false 4.375,8.427 4.615,8.063 4.615,8.063 4.813,8.063 false 3.156,8.51 2.979,8.146 2.979,8.146 2.75,8.146 false 1.865,7.75 1.604,8.073 1.604,8.073 1.417,8.073 false 2.49,7.469 2.104,7.156 2.104,7.156 1.854,7.156 false 2.896,6.896 1.792,6.708 1.792,6.708 1.573,6.708 false 5.271,7.76 5.688,8.167 5.688,8.167 5.875,8.167 false 1.615,3.865 2.104,4.063 0.49,0.198 10 false 5 (0.20) 0.042,8.667 0.396,8.865 0.354,0.198 10 false *c 1.115,8.354 1.385,8.531 0.271,0.177 10 false *7 1.219,8.01 1.51,8.219 0.292,0.208 10 false *6 2.542,8.083 2.854,8.281 0.313,0.198 10 false *5 1.667,7.094 1.979,7.292 0.313,0.198 10 false *5 1.385,6.635 2,6.833 0.615,0.198 10 false *4 5.156,6.615 5.927,6.813 0.771,0.198 10 false *1 6.135,7.104 6.594,7.302 0.458,0.198 10 false *2 4.865,8 5.323,8.198 0.458,0.198 10 false *2 5.927,8.104 6.698,8.302 0.771,0.198 10 false *3 1.469,5.542 1.958,5.74 0.49,0.198 10 false 5 (0.20)
*1 Plug Weld *2 Reference Surface
*3 New Panel *4 Fillet Weld
*5 Putty *6 Vehicle Side Panel
*7 Cross Section Illustration - -
*c mm (in.) - -


K146137