REMOVAL
| Symbol Meaning | |
|---|---|
|
Remove Weld Points |
|
Cut and Join Location |
|
Cut Location for Supply Parts |
*a in illustration above indicates where the adhesive is located.
Roughly cut open the panel so that the adhesive can be reached. Cut through the adhesive with a cut chisel to remove the panel.
In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.
| *A | for Standard Body | - | - |
| *b | mm (in.) | - | - |
| *A | for Long Body | - | - |
| *b | mm (in.) | - | - |
| *A | for Super Long Body | - | - |
| *b | mm (in.) | - | - |
INSTALLATION
| Symbol Meaning | |
|---|---|
|
Plug Weld |
|
Cut and Join Location |
|
Fillet Weld |
|
Butt Weld |
|
Body Sealer |
Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.
Before installing a new part, apply body sealer.
Apply body sealer in an even, continuous bead.
Before temporarily installing the new parts, weld the rear body panel front and emergency step base with the standard number of welding points. (w/ Emergency Step)
*a Dent one part about 1 to 2 mm (0.04 to 0.08 in.).
Before installing a new part, apply body sealer.
Apply body sealer evenly about 5 mm (0.20 in.) from the flange, avoiding any oozing.
Apply body sealer evenly, about 3 to 4 mm (0.12 to 0.16 in.) in diameter.
Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115) to the area indicated by *b in the illustration.
Apply a light coat of adhesive around the plug welding points.
Apply enough adhesive to the panels.
Follow the welding conditions when welding *c to assure sufficient weld strength.
| Plug Diameter | Welding Wire Diameter | Plug Welding Hole Pitch | Shield Gas |
|---|---|---|---|
| 4 mm (0.16 in.) | 0.6 mm (0.02 in.) | 25 mm (0.98 in.) | Metal active gas (Ar 80% + CO2 20%) |
| 5 mm (0.20 in.) | 0.8 mm (0.03 in.) | 30mm (1.18 in.) |
After welding, apply body sealer to the corresponding parts. (See the painting / coating)
After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.
| *A | w/ Emergency Step | - | - |
| *1 | REAR BODY PANEL FRONT | *2 | EMERGENCY STEP BASE |
| *A | for Standard Body | - | - |
| *d | mm (in.) | - | - |
| *A | for Standard Body | - | - |
| *1 | REAR BODY PANEL FRONT | - | - |
| *d | mm (in.) | - | - |
| *A | for Standard Body | - | - |
| *A | for Standard Body | - | - |
| *1 | Fillet Weld | *2 | Putty |
| *3 | Vehicle Side Panel | *4 | Plug Weld |
| *5 | Reference Surface | *6 | New Panel |
| *7 | Cross Section Illustration | - | - |
| *d | mm (in.) | - | - |
| *A | for Long Body | - | - |
| *d | mm (in.) | - | - |
| *A | for Long Body | - | - |
| *1 | REAR BODY PANEL FRONT | - | - |
| *d | mm (in.) | - | - |
| *A | for Long Body | - | - |
| *A | for Long Body | - | - |
| *1 | Fillet Weld | *2 | Putty |
| *3 | Vehicle Side Panel | *4 | Plug Weld |
| *5 | Reference Surface | *6 | New Panel |
| *7 | Cross Section Illustration | - | - |
| *d | mm (in.) | - | - |
| *A | for Super Long Body | - | - |
| *d | mm (in.) | - | - |
| *A | for Super Long Body | - | - |
| *1 | FRONT SIDE PANEL OUTER | *2 | REAR BODY PANEL FRONT |
| *d | mm (in.) | - | - |
| *A | for Super Long Body | - | - |
| *A | for Super Long Body | - | - |
| *1 | Fillet Weld | *2 | Putty |
| *3 | Vehicle Side Panel | *4 | Plug Weld |
| *5 | Reference Surface | *6 | New Panel |
| *7 | Cross Section Illustration | - | - |
| *d | mm (in.) | - | - |
| *A | for Super Long Body | - | - |
| *1 | Plug Welding Hole Center | - | - |
| *d | mm (in.) | - | - |