Home › Vehicle Exterior › BODY PANEL › SIDE PANEL NO.3 LH › from 2019.08
BM2850E _01 Vehicle Exterior _075893 BODY PANEL _0369113 SIDE PANEL NO.3 LH F

BODY PANEL  SIDE PANEL NO.3 LH  ASSEMBLY REPLACEMENT  


K139857

With the side panel No.4 LH removed.


REMOVAL



Symbol Meaning
K108818

Remove Weld Points
K108828

Cut Location for Supply Parts

REMOVAL POINT
1.

*a in illustration above indicates where the adhesive is located.

2.

Roughly cut open the panel so that the adhesive can be reached. Cut through the adhesive with a cut chisel to remove the panel.

HINT:

In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.



K146167C01
4.052,6.604 3.292,5.271 false 4.052,6.594 3.521,5.292 false 4.052,6.583 3.844,5.281 false 4.063,6.573 4.208,5.281 false 4.063,6.583 4.573,5.271 false 4.052,6.594 4.344,6.594 false 0.302,0.302 0.615,0.458 0.313,0.156 10 false *A 4.396,6.521 4.708,6.719 0.313,0.198 10 false *a
*A for Standard Body - -


K146168C01
3.958,6.5 3.292,5.281 false 3.958,6.5 3.531,5.292 false 3.969,6.49 3.854,5.281 false 3.969,6.479 4.208,5.271 false 3.969,6.49 4.563,5.26 false 3.958,6.5 4.229,6.5 false 0.292,0.24 0.604,0.396 0.313,0.156 10 false *A 4.271,6.427 4.583,6.625 0.313,0.198 10 false *a
*A for Long Body - -


K153328C02
4.083,7.417 3.917,7.417 3.917,7.417 3.031,6.313 false 3.917,7.417 3.25,6.302 false 3.917,7.417 3.833,6.302 false 3.917,7.417 4.146,6.302 false 3.917,7.417 4.385,6.302 false 3.917,7.417 4.531,6.302 false 3.917,7.417 3.521,6.302 false 0.167,0.167 0.479,0.323 0.313,0.156 10 false *A 4.156,7.333 4.469,7.531 0.313,0.198 10 false *a
*A for Super Long Body - -


K146169

INSTALLATION


Symbol Meaning
K108823

Plug Weld
K108831

Butt Weld
K108834

Body Sealer


INSTALLATION POINT
1.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.

2.

Before installing a new part, apply body sealer.

HINT:

Apply body sealer in an even, continuous bead.


3.

Before temporarily installing the new parts, weld the rear body panel rear, side panel to rear mudguard bracket, mudguard bracket rear and fuel inlet box with the standard number of welding points.

4.

Before installing a new part, apply body sealer.

HINT:
·

Apply body sealer evenly about 5 mm (0.20 in.) from the flange, avoiding any oozing.

·

Apply body sealer evenly, about 3 to 4 mm (0.12 to 0.16 in.) in diameter.



5.

Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115) to the area indicated by *a in the illustration.

HINT:
·

Apply a light coat of adhesive around the plug welding points.

·

Apply enough adhesive to the panels.



6.

Follow the welding conditions when welding *b to assure sufficient weld strength.

Plug Diameter Welding Wire Diameter Plug Welding Hole Pitch Shield Gas
4 mm (0.16 in.) 0.6 mm (0.02 in.) 25 mm (0.98 in.) Metal active gas (Ar 80% + CO2 20%)
5 mm (0.20 in.) 0.8 mm (0.03 in.) 30mm (1.18 in.)

7.

After welding, apply body sealer to the corresponding parts. (See the painting / coating)

8.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.


K146170C01
3.156,4.281 4.25,3.719 4.25,3.719 4.458,3.719 false 1.958,5.052 4.198,4.271 4.198,4.271 4.438,4.271 false 0.552,7.281 0.333,7.281 0.333,7.281 1.594,5.781 false 1.188,7.042 0.979,7.042 0.979,7.042 1.479,6.229 false 4.51,3.656 4.823,3.813 0.313,0.156 10 false *1 0.594,7.229 0.906,7.385 0.313,0.156 10 false *2 1.26,6.979 1.573,7.135 0.313,0.156 10 false *3 4.5,4.229 4.813,4.385 0.313,0.156 10 false *4
*1 REAR BODY PANEL REAR *2 SIDE PANEL TO REAR MUDGUARD BRACKET
*3 MUDGUARD BRACKET REAR *4 FUEL INLET BOX


K146171C04
4.167,5.552 3.302,4.396 false 4.177,5.552 3.521,4.396 false 4.167,5.531 3.833,4.396 false 4.177,5.531 4.219,4.396 false 4.177,5.542 4.563,4.385 false 4.177,5.552 4.365,5.552 false 0.219,0.292 0.531,0.448 0.313,0.156 10 false *A 0.198,8.594 0.51,8.75 0.313,0.156 10 false *c 4.406,5.49 4.719,5.646 0.313,0.156 10 false *a 2.781,6.771 3.292,6.969 0.51,0.198 10 false 5 (0.20)
*A for Standard Body - -
*c mm (in.) - -


K146172C05
3.906,5.615 3.292,4.385 false 3.906,5.604 3.51,4.375 false 3.917,5.615 3.823,4.385 false 3.927,5.594 4.219,4.385 false 3.927,5.604 4.563,4.375 false 3.927,5.615 4.146,5.615 false 0.208,0.219 0.521,0.375 0.313,0.156 10 false *A 0.188,8.625 0.5,8.781 0.313,0.156 10 false *c 4.188,5.552 4.5,5.708 0.313,0.156 10 false *a 2.802,6.802 3.313,7.021 0.51,0.219 10 false 5 (0.20)
*A for Long Body - -
*c mm (in.) - -


K153331C02
3.917,6.333 3.75,6.333 3.75,6.333 3.021,5.323 false 3.75,6.333 3.24,5.313 false 3.75,6.333 3.51,5.313 false 3.75,6.333 3.833,5.313 false 3.75,6.333 4.135,5.313 false 3.75,6.333 4.375,5.313 false 3.75,6.333 4.531,5.313 false 2.438,1.635 2.156,1 2.156,1 1.99,1 false 4.594,1.656 5,1 5,1 5.167,1 false 0.167,0.167 0.479,0.323 0.313,0.156 10 false *A 0.167,8.583 0.479,8.74 0.313,0.156 10 false *c 3.979,6.24 4.292,6.438 0.313,0.198 10 false *a 1.813,0.917 2.125,1.073 0.313,0.156 10 false *1 5.24,0.906 5.552,1.063 0.313,0.156 10 false *2 2.792,7.365 3.354,7.563 0.563,0.198 10 false 5 (0.20)
*A for Super Long Body - -
*1 REAR BODY PANEL REAR *2 SIDE PANEL RELIEF GUSSET NO.4
*c mm (in.) - -


K153332C02
5.365,6.458 5.583,6.167 5.583,6.167 5.75,6.167 false 0.167,0.167 0.479,0.323 0.313,0.156 10 false *A 5.813,6.073 6.125,6.229 0.313,0.156 10 false *1 0.167,8.583 0.479,8.74 0.313,0.156 10 false *c 2.167,7.583 2.479,7.781 0.313,0.198 10 false *b 4.188,0.885 4.5,1.083 0.313,0.198 10 false *b 4.177,1.5 4.49,1.698 0.313,0.198 10 false *b 5.667,3.167 5.979,3.365 0.313,0.198 10 false *b 5.667,3.927 5.979,4.125 0.313,0.198 10 false *b 5.667,4.635 5.979,4.833 0.313,0.198 10 false *b 4.563,6.438 5.313,6.635 0.75,0.198 10 false 3.7 (0.15) 5.76,7.26 6.594,7.458 0.833,0.198 10 false 11.8 (0.46)
*A for Super Long Body - -
*1 Plug Welding Hole Center - -
*c mm (in.) - -


K146173