Home › Vehicle Exterior › BODY PANEL › ROOF PANEL NO.5 › from 2019.08
BM2850E _01 Vehicle Exterior _075893 BODY PANEL _0369079 ROOF PANEL NO.5 F

BODY PANEL  ROOF PANEL NO.5  CUT AND JOIN REPLACEMENT SECTIONS (PATTERN 2)  


K154010

With the roof panel No.6 removed.


REMOVAL


Symbol Meaning
K108818

Remove Weld Points
K108827

Cut and Join Location


REMOVAL POINT
1.

*a in illustration above indicates where the adhesive is located.

2.

Roughly cut open the panel so that the adhesive can be reached. Cut through the adhesive with a cut chisel to remove the panel.

HINT:

In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.



K145002C01
1.75,3.188 1.917,2.917 1.917,2.917 2.083,2.917 false 1.75,3.427 1.917,2.917 false 1.635,3.198 1.5,2.917 1.5,2.917 1.333,2.917 false 1.635,3.427 1.5,2.917 false 0.167,0.177 0.479,0.333 0.313,0.156 10 false *A 0.167,0.427 0.479,0.583 0.313,0.156 10 false *B 0.167,8.5 0.479,8.656 0.313,0.156 10 false *b 2.135,2.833 2.448,3.031 0.313,0.198 10 false *a 1.167,2.833 1.479,3.031 0.313,0.198 10 false *a 2.646,5.177 3.229,5.375 0.583,0.198 10 false 25 (0.98)
*A for Glide Type *B LH
*b mm (in.) - -


K145003C01
1.75,3.208 1.917,2.917 1.917,2.917 2.083,2.917 false 1.75,3.427 1.917,2.917 false 1.646,3.219 1.5,2.917 1.5,2.917 1.333,2.917 false 1.635,3.438 1.5,2.917 false 0.167,0.167 0.479,0.323 0.313,0.156 10 false *A 0.167,0.427 0.479,0.583 0.313,0.156 10 false *B 0.167,8.51 0.479,8.667 0.313,0.156 10 false *b 2.135,2.833 2.448,3.031 0.313,0.198 10 false *a 1.156,2.833 1.469,3.031 0.313,0.198 10 false *a 2.635,5.167 3.219,5.365 0.583,0.198 10 false 25 (0.98)
*A for Folding Type *B LH
*b mm (in.) - -


K145004C01
5.281,3.573 5.417,3.25 5.417,3.25 5.583,3.25 false 5.292,3.802 5.417,3.25 false 5.167,3.792 5,3.25 false 5.167,3.573 5,3.25 5,3.25 4.833,3.25 false 0.167,0.167 0.479,0.323 0.313,0.156 10 false *A 0.167,8.51 0.479,8.667 0.313,0.156 10 false *b 3.896,5.448 4.479,5.646 0.583,0.198 10 false 25 (0.98) 4.656,3.167 4.969,3.365 0.313,0.198 10 false *a 5.635,3.177 5.948,3.375 0.313,0.198 10 false *a
*A RH - -
*b mm (in.) - -


INSTALLATION


Symbol Meaning
K108823

Plug Weld
K108827

Cut and Join Location
K108831

Butt Weld


INSTALLATION POINT (LH)
1.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.

2.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)

3.

If the entire supply part is not needed, remove the part of the supply part that is needed.

4.

Before temporarily installing the new parts, weld the NO.1 side panel, roof side panel outer and roof drip side channel center No.1 with the standard number of welding points.

5.

Follow the welding conditions when welding *a to assure sufficient weld strength.

Plug Diameter Welding Wire Diameter Plug Welding Hole Pitch Shield Gas
4 mm (0.16 in.) 0.6 mm (0.02 in.) 25 mm (0.98 in.) Metal active gas (Ar 80% + CO2 20%)
5 mm (0.20 in.) 0.8 mm (0.03 in.) 30mm (1.18 in.)

6.

Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115) to the area indicated by *b in the illustration.

HINT:
·

Apply a light coat of adhesive around the plug welding points.

·

Apply enough adhesive to the panels.



7.

After welding, apply body sealer to the corresponding parts. (See the painting / coating)

8.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.


INSTALLATION POINT (RH)
1.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.

2.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)

3.

If the entire supply part is not needed, remove the part of the supply part that is needed.

4.

Before temporarily installing the new parts, weld the front body pillar upper outer and roof side panel outer with the standard number of welding points.

5.

Follow the welding conditions when welding *a to assure sufficient weld strength.

Plug Diameter Welding Wire Diameter Plug Welding Hole Pitch Shield Gas
4 mm (0.16 in.) 0.6 mm (0.02 in.) 25 mm (0.98 in.) Metal active gas (Ar 80% + CO2 20%)
5 mm (0.20 in.) 0.8 mm (0.03 in.) 30mm (1.18 in.)

6.

Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115) to the area indicated by *b in the illustration.

HINT:
·

Apply a light coat of adhesive around the plug welding points.

·

Apply enough adhesive to the panels.



7.

After welding, apply body sealer to the corresponding parts. (See the painting / coating)

8.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.


K154003C02
4.583,1.5 5,1.833 5,1.833 5.167,1.833 false 2.896,4.573 2.5,3.833 2.5,3.833 2.333,3.833 false 3.552,7.938 3.75,8.167 3.75,8.167 3.917,8.167 false 0.219,0.281 0.531,0.438 0.313,0.156 10 false *A 5.24,1.771 5.552,1.927 0.313,0.156 10 false *1 2.135,3.76 2.448,3.917 0.313,0.156 10 false *2 5.344,4.375 5.656,4.531 0.313,0.156 10 false *a 0.25,8.5 0.563,8.656 0.313,0.156 10 false *c 4,8.115 4.302,8.333 0.302,0.219 10 false *3 2.813,6.635 3.51,6.833 0.698,0.198 10 false 3.7 (0.15) 3.906,7.458 4.656,7.656 0.75,0.198 10 false 11.8 (0.46) 4.208,0.781 4.875,0.979 0.667,0.198 10 false 100 (3.94)
*A LH - -
*1 NO.1 SIDE PANEL *2 ROOF SIDE PANEL OUTER
*3 Plug Welding Hole Center - -
*c mm (in.) - -


K146292C03
2.938,3.771 3.125,3.104 3.125,3.104 3.385,3.104 false 3.823,4.146 3.979,4.938 3.979,4.938 4.24,4.938 false 0.219,0.281 0.531,0.438 0.313,0.156 10 false *A 3.427,3.042 3.74,3.198 0.313,0.156 10 false *1 4.292,4.875 4.604,5.031 0.313,0.156 10 false *2
*A LH - -
*1 ROOF SIDE PANEL OUTER *2 ROOF DRIP SIDE CHANNEL CENTER NO.1


K154004C02
1.74,3.167 1.917,2.833 1.917,2.833 2.083,2.833 false 1.667,3.135 1.5,2.833 1.5,2.833 1.333,2.833 false 1.76,3.365 1.917,2.833 false 1.625,3.354 1.5,2.833 false 0.281,0.229 0.594,0.385 0.313,0.156 10 false *A 0.281,0.385 0.594,0.542 0.313,0.156 10 false *B 2.125,2.771 2.438,2.927 0.313,0.156 10 false *b 1.167,2.771 1.479,2.927 0.313,0.156 10 false *b
*A for Glide Type *B LH


K154005C02
1.729,3.167 1.917,2.833 1.917,2.833 2.083,2.833 false 1.74,3.354 1.917,2.833 false 1.646,3.146 1.5,2.833 1.5,2.833 1.333,2.833 false 1.635,3.354 1.5,2.833 false 0.302,0.344 0.615,0.5 0.313,0.156 10 false *A 0.302,0.5 0.615,0.656 0.313,0.156 10 false *B 1.167,2.76 1.479,2.917 0.313,0.156 10 false *b 2.135,2.76 2.448,2.917 0.313,0.156 10 false *b
*A for Folding Type *B LH


K154006C02
2.615,1.938 2.25,2.25 2.25,2.25 2.083,2.25 false 3.781,4.594 4,3.917 4,3.917 4.167,3.917 false 3.5,7.917 3.667,8.167 3.667,8.167 3.833,8.167 false 0.219,0.281 0.531,0.438 0.313,0.156 10 false *A 1.896,2.188 2.208,2.344 0.313,0.156 10 false *1 4.219,3.854 4.531,4.01 0.313,0.156 10 false *2 1.083,4.354 1.396,4.51 0.313,0.156 10 false *a 0.25,8.5 0.563,8.656 0.313,0.156 10 false *c 3.906,8.104 4.177,8.333 0.271,0.229 10 false *3 2.417,1.229 3.167,1.427 0.75,0.198 10 false 100 (3.94) 3.708,6.635 4.458,6.833 0.75,0.198 10 false 3.7 (0.15) 2.49,7.458 3.24,7.656 0.75,0.198 10 false 11.8 (0.46)
*A RH - -
*1 FRONT BODY PILLAR UPPER OUTER *2 ROOF SIDE PANEL OUTER
*3 Plug Welding Hole Center - -
*c mm (in.) - -


K154007C02
5.281,3.521 5.417,3.167 5.417,3.167 5.583,3.167 false 5.281,3.74 5.417,3.167 false 5.167,3.51 5,3.167 5,3.167 4.833,3.167 false 5.167,3.729 5,3.167 false 0.198,0.24 0.51,0.396 0.313,0.156 10 false *A 4.667,3.094 4.979,3.25 0.313,0.156 10 false *b 5.625,3.094 5.938,3.25 0.313,0.156 10 false *b
*A RH - -