With the side panel No.1 RH removed.
REMOVAL
| Symbol Meaning | |
|---|---|
|
Remove Weld Points |
|
Remove Weld Points |
*a and *b is reused.
After removing the *a and *b, remove the No.3 pillar.
*c in illustration indicates where the adhesive is located.
Roughly cut open the panel so that the adhesive can be reached. Cut through the adhesive with a cut chisel to remove the panel.
In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.
| *A | for Glide Type | - | - |
| *A | for Glide Type | - | - |
| *A | for Folding Type | - | - |
| *A | for Folding Type | - | - |
INSTALLATION
| Symbol Meaning | |
|---|---|
|
Spot Weld |
|
Plug Weld |
|
Plug Weld |
|
Body Sealer |
Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.
Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)
Before installing a new part, apply body sealer.
Apply body sealer in an even, continuous bead.
Before temporarily installing the new parts, weld the No.4 pillar, center door pillar gusset front, lower rail plate inner No.4, stiffener bracket No.5, center body pillar reinforce sub-assembly lower rear and center door pillar dust proof plate rear with the standard number of welding points.
Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115) to the area indicated by *a in the illustration.
Apply a light coat of adhesive around the plug welding points.
Apply enough adhesive to the panels.
After welding the No.4 pillar, center door pillar gusset front, lower rail plate inner No.4, stiffener bracket No.5, center body pillar reinforce sub-assembly lower rear and center door pillar dust proof plate rear to the vehicle side, install the *b and *c.
After welding, apply body sealer and undercoating to the corresponding parts. (See the painting / coating)
After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.
Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.
Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)
Before installing a new part, apply body sealer.
Apply body sealer in an even, continuous bead.
Before temporarily installing the new parts, weld the No.3 pillar, center door pillar gusset front, center door orening panel lower inner front, stiffener bracket No.5 and center body pillar plate outer with the standard number of welding points.
Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115) to the area indicated by *a in the illustration.
Apply a light coat of adhesive around the plug welding points.
Apply enough adhesive to the panels.
After welding the No.3 pillar, center door pillar gusset front, center door orening panel lower inner front, stiffener bracket No.5 and center body pillar plate outer to the vehicle side, install the *b and *c.
After welding, apply body sealer and undercoating to the corresponding parts. (See the painting / coating)
After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.
| *A | for Glide Type | - | - |
| *1 | NO.4 PILLAR | *2 | CENTER DOOR PILLAR GUSSET FRONT |
| *3 | LOWER RAIL PLATE INNER NO.4 | *4 | STIFFENER BRACKET NO.5 |
| *5 | CENTER BODY PILLAR REINFORCE SUB-ASSEMBLY LOWER REAR | *6 | CENTER DOOR PILLER DUST PROOF PLATE REAR |
| *A | for Glide Type | - | - |
| *A | for Glide Type | - | - |
| *A | for Folding Type | - | - |
| *1 | NO.3 PILLAR | *2 | CENTER DOOR PILLAR GUSSET FRONT |
| *3 | CENTER DOOR ORENING PANEL LOWER INNER FRONT | *4 | STIFFENER BRACKET NO.5 |
| *5 | CENTER BODY PILLAR PLATE OUTER | - | - |
| *A | for Folding Type | - | - |
| *A | for Folding Type | - | - |