Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM › 2017.01–2019.08
NM2850E _58 Vehicle Interior _074251 HEATING / AIR CONDITIONING _0361397 AIR CONDITIONING SYSTEM CO CONTROL F

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  CONTROL  AIR CONDITIONING CONTROL  


FUNCTION OF MAIN COMPONENTS


Room Cooler System for the Manual Air Conditioner
Component Function
Air Conditioning Amplifier Assembly Controls the room cooler by signals from switches, sensors, and other devices.
Air Conditioning Control Assembly Switches the recirculation/fresh air and configures the blow temperature and blower level.
Room Cooler Unit (Cooler Unit Assembly) No. 1 Cooler Thermistor Detects the blow temperature of the room cooler unit (cooler unit assembly).
Blower Resistor (Room Cooler) Changes the resistance value according to operation of the room cooler blower lever and controls the number of revolutions of the room cooler blower motor (blower motor with fan sub-assembly).
Room Cooler Blower Motor (Blower Motor with Fan Sub-assembly) Driven by the current from the blower resistor (room cooler) and distributes air inside the vehicle.
Compressor with Magnet Clutch Assembly Suctions, compresses, and ejects the refrigerant.
Condenser with Receiver Assembly No. 1 Pressure Switch Detects the refrigerant pressure.
Condenser Blower Motor Assembly Cools cooler condenser core.
Roof Ventilator Damper Servo Sub-assembly Driven according to operation of the room cooler recirculation/fresh air selector switch and open and close the recirculation/fresh air control door for the room cooler.
Air Conditioning Idle Up VSV (Vacuum Switching Valve Assembly)*1 Driven by signals from the air conditioning compressor relay.
ECM*2 Outputs signals to the air conditioning amplifier assembly.

HINT:

*1: Models with air conditioning idle up VSV (vacuum switching valve assembly)

*2: Models without 14B or 1HZ engine



Front Heater System for the Manual Air Conditioner
Component Function
Air Conditioning Control Assembly Front Heater Blower Lever Configures the blower level.
Front Heater Temperature Control Lever Configures the blower temperature.
Front Heater Unit Heater Blower Resistor (Front Heater) Changes the resistance value according to operation of the front heater blower lever and controls the number of revolutions of the front heater blower motor (front heater blower case sub-assembly).
Front Heater Blower Motor (Front Heater Blower Case Sub-assembly) Driven by the current from the heater blower resistor (front heater) and distributes air inside the vehicle.

Rear Heater System for the Manual Air Conditioner
Component Function
Air Conditioning Control Assembly Rear Heater Blower Lever Configures the blower level.
Rear Heater Temperature Control Lever Configures the blower temperature.
Rear Heater Assembly/ No. 2 Rear Heater Assembly Heater Blower Resistor (Rear Heater) Changes the resistance value according to operation of the rear heater blower lever and controls the number of revolutions of the rear heater blower motor (rear heater blower case sub-assembly).
Rear Heater Blower Motor (Rear Heater Blower Case Sub-assembly) Driven by the current from the heater blower resistor (rear heater) and distributes air inside the vehicle.

SYSTEM CONTROL


a.

Temperature Control (Room Cooler System for the Manual Air Conditioner)

i.

Detects the evaporator blow temperature from No. 1 cooler thermistor and switches the magnet clutch on and off when the room cooler is on. At maximum cooling, switches off at 3°C or lower and switches on at 4°C or higher.



b.

Air Conditioning Shutoff Control During Acceleration (Room Cooler System for the Manual Air Conditioner)

i.

If an air conditioner shutoff signal is input from the ECM, the magnet clutch of the interim compressor with magnet clutch assembly is switched off.