CONSTRUCTION
A brake actuator assembly integrated with a skid control computer was employed for vehicles with an VSC that uses CAN communication. The brake actuator assembly has a small size and light weight while still having sufficient ejection performance and guarantees excellent safety and running performance even for heavy vehicles.
The brake actuator assembly consists of the actuator, skid control ECU, solenoid relay, pump motor, and master cylinder pressure sensor.
| *a | Actuator Portion | *b | Skid Control ECU |
The actuator portion consists of 10 solenoid valves, 2 pressure regulator valves, 2 pump, 2 reservoirs, and master cylinder pressure sensor.
The 10 solenoid valves consist of 2 master cylinder cut solenoid valves [(1), (2)], 4 pressure holding solenoid valves [(3), (4), (5), (6)], and 4 pressure reduction solenoid valves [(7), (8), (9), (10)].
| *1 | Brake Master Cylinder Sub-assembly | *2 | Brake Actuator Assembly |
| *3 | Master Cylinder Pressure Sensor | *4 | Pump |
| *5 | Pressure Regulator Valves | *6 | Reservoirs |
| *7 | Rear Left Wheel Cylinder | *8 | Rear Right Wheel Cylinder |
| *9 | Front Left Wheel Cylinder | *10 | Front Right Wheel Cylinder |
OPERATION
ABS with EBD Operation
Based on the signals received from the 4 wheel speed sensors and yaw rate and deceleration sensor, the skid control ECU calculates the wheel rotation speed and deceleration for each wheel, in order to check for a wheel slippage condition. According to the slippage condition, the ECU controls the pressure holding solenoid valves and pressure reduction solenoid valves in order to adjust the fluid pressure of the brakes for each of the wheels in the following 3 modes: pressure reduction, pressure holding, and pressure increase modes.
Power Assist Brake (PAB) Operation
In certain situations when the vacuum pressure of the vacuum booster calculated using the vacuum sensor and master cylinder pressure sensor is low, the skid control ECU may provide brake assist. Or in the event of a brake booster failure, based on the brake pedal load sensing switch and master cylinder pressure sensor signal, the skid control ECU may provide brake assist.
If the skid control ECU judges the need for additional brake assist, pressure is generated by the pump in the brake actuator and directed to the wheel cylinder to apply a large amount of fluid pressure.
| *1 | Brake Master Cylinder Sub-assembly | *2 | Brake Actuator Assembly |
| *3 | Master Cylinder Pressure Sensor | *4 | Pump |
| *5 | Pressure Regulator Valves | *6 | Reservoirs |
| *7 | Rear Left Wheel Cylinder | *8 | Rear Right Wheel Cylinder |
| *9 | Front Left Wheel Cylinder | *10 | Front Right Wheel Cylinder |
| Item | Power Assist Brake (PAB) Not Activated | Power Assist Brake (PAB) Activated | |
|---|---|---|---|
|
*: The solenoid valves control the hydraulic pressure by adjusting continually between "open" and "closed" according to the operating conditions. |
|||
| (1), (2) | Master Cylinder Cut Solenoid Valve | OFF/Open | ON* |
| Port: (A), (B) | |||
| (3), (4), (5), (6) | Pressure Holding Solenoid Valve | OFF/Open | OFF/Open |
| Port: (C), (D), (E), (F) | |||
| (7), (8), (9), (10) | Pressure Reduction Solenoid Valve | OFF/Closed | OFF/Closed |
| Port: (G), (H), (I), (J) | |||
Brake Assist Operation
In the event of emergency braking, the skid control ECU determines the driver's intention based on the speed of the pressure increase in the master cylinder determined by the master cylinder pressure sensor signal. If the skid control ECU determines the need for additional brake assist, pressure is generated by the pump in the brake actuator assembly and directed to the wheel cylinder to apply a large amount of fluid pressure.
| *1 | Brake Master Cylinder Sub-assembly | *2 | Brake Actuator Assembly |
| *3 | Master Cylinder Pressure Sensor | *4 | Pump |
| *5 | Pressure Regulator Valves | *6 | Reservoirs |
| *7 | Rear Left Wheel Cylinder | *8 | Rear Right Wheel Cylinder |
| *9 | Front Left Wheel Cylinder | *10 | Front Right Wheel Cylinder |
| Item | Brake Assist Not Activated | Brake Assist Activated | |
|---|---|---|---|
|
*: The solenoid valves control the hydraulic pressure by adjusting continually between "open" and "closed" according to the operating conditions. |
|||
| (1), (2) | Master Cylinder Cut Solenoid Valve | OFF/Open | ON* |
| Port: (A), (B) | |||
| (3), (4), (5), (6) | Pressure Holding Solenoid Valve | OFF/Open | OFF/Open |
| Port: (C), (D), (E), (F) | |||
| (7), (8), (9), (10) | Pressure Reduction Solenoid Valve | OFF/Closed | OFF/Closed |
| Port: (G), (H), (I), (J) | |||
TRC Operation
The fluid pressure generated by the pump is regulated by the master cylinder cut solenoid valve to achieve the required pressure. Thus, the brakes for the drive wheels are controlled in the following 3 modes: pressure reduction, pressure holding, and pressure increase modes, to control slippage of the drive wheels.
The diagram below shows the hydraulic circuit in the pressure increase mode when the TRC system is activated. The pressure holding solenoid valve and the pressure reduction solenoid valve are turned ON/OFF according to the ABS and EBD operation pattern.
| *1 | Brake Master Cylinder Sub-assembly | *2 | Brake Actuator Assembly |
| *3 | Master Cylinder Pressure Sensor | *4 | Pump |
| *5 | Pressure Regulator Valves | *6 | Reservoirs |
| *7 | Rear Left Wheel Cylinder | *8 | Rear Right Wheel Cylinder |
| *9 | Front Left Wheel Cylinder | *10 | Front Right Wheel Cylinder |
| Item | TRC Not Activated | TRC Activated | ||||
|---|---|---|---|---|---|---|
| Pressure Increase Mode | Pressure Holding Mode | Pressure Reduction Mode | ||||
|
*: The solenoid valves control the hydraulic pressure by adjusting continually between "open" and "closed" according to the operating conditions. |
||||||
| (1) | Master Cylinder Cut Solenoid Valve | OFF/Open | ON* | ON* | ON* | |
| Port: (A) | ||||||
| (2) | Master Cylinder Cut Solenoid Valve | OFF/Open | ON* | ON* | ON* | |
| Port: (B) | ||||||
| Front Brake | (5), (6) | Pressure Holding Valve | OFF/Open | ON/Closed | ON/Closed | ON/Closed |
| Port: (E), (F) | ||||||
| (9), (10) | Pressure Reduction Valve | OFF/Closed | OFF/Closed | OFF/Closed | OFF/Closed | |
| Port: (I), (J) | ||||||
| Wheel Cylinder Pressure | - | - | - | - | ||
| Rear Brake | (3), (4) | Pressure Holding Valve | OFF/Open | OFF/Open | ON/Closed | ON/Closed |
| Port: (C), (D) | ||||||
| (7), (8) | Pressure Reduction Valve | OFF/Closed | OFF/Closed | OFF/Closed | ON/Open | |
| Port: (G), (H) | ||||||
| Wheel Cylinder Pressure | - | Increase | Holding | Reduce | ||
VSC Operation
The VSC system, by way of solenoid valves, controls the fluid pressure that is generated by the pump and applies it to the brake wheel cylinder of each wheel in the following 3 modes: pressure reduction, pressure holding, and pressure increase modes. As a result, the tendency of the vehicle to experience a front wheel skid or rear wheel skid is controlled.
Front Wheel Skid Restraining Control (Right Turn)
For front wheel skid restraining control, the brakes of the front wheel of the outer side of the turn and the rear wheels are applied. Also, depending on whether the brake is ON or OFF and the condition of the vehicle, there are circumstances in which the brake might not be applied to the wheels even if those wheels are targeted for braking. The diagram below shows the hydraulic circuit in the pressure increase mode, as it controls the front wheel skid condition while the vehicle makes a right turn. In other operating modes, the pressure holding valve and the pressure reduction valve are turned ON/OFF according to the ABS with EBD operation pattern.
| *1 | Brake Master Cylinder Sub-assembly | *2 | Brake Actuator Assembly |
| *3 | Master Cylinder Pressure Sensor | *4 | Pump |
| *5 | Pressure Regulator Valves | *6 | Reservoirs |
| *7 | Rear Left Wheel Cylinder | *8 | Rear Right Wheel Cylinder |
| *9 | Front Left Wheel Cylinder | *10 | Front Right Wheel Cylinder |
| Item | VSC Not Activated | VSC Activated | ||||
|---|---|---|---|---|---|---|
| Pressure Increase Mode | Pressure Holding Mode | Pressure Reduction Mode | ||||
|
*: The solenoid valves control the hydraulic pressure by adjusting continually between "open" and "closed" according to the operating conditions. |
||||||
| (1), (2) | Master Cylinder Cut Solenoid Valve | OFF/Open | ON* | ON* | ON* | |
| Port: (A), (B) | ||||||
| Front Brake | (5) | Pressure Holding Valve | OFF/Open | OFF/Open | ON/Closed | ON/Closed |
| Port: (E) | ||||||
| (6) | Pressure Holding Valve | OFF/Open | ON/Closed | ON/Closed | ON/Closed | |
| Port: (F) | ||||||
| (9) | Pressure Reduction Valve | OFF/Closed | OFF/Closed | OFF/Closed | ON/Open | |
| Port: (I) | ||||||
| (10) | Pressure Reduction Valve | OFF/Closed | OFF/Closed | OFF/Closed | OFF/Closed | |
| Port: (J) | ||||||
| Wheel Cylinder Pressure | Right | - | - | - | - | |
| Left | - | Increase | Holding | Reduce | ||
| Rear Brake | (3) | Pressure Holding Valve | OFF/Open | OFF/Open | ON/Closed | ON/Closed |
| Port: (C) | ||||||
| (4) | Pressure Holding Valve | OFF/Open | OFF/Open | ON/Closed | ON/Closed | |
| Port: (D) | ||||||
| (7) | Pressure Reduction Valve | OFF/Closed | OFF/Closed | OFF/Closed | ON/Open | |
| Port: (G) | ||||||
| (8) | Pressure Reduction Valve | OFF/Closed | OFF/Closed | OFF/Closed | ON/Open | |
| Port: (H) | ||||||
| Wheel Cylinder Pressure | Right | - | Increase | Holding | Reduce | |
| Left | - | Increase | Holding | Reduce | ||
Rear Wheel Skid Restraining Control (Right Turn)
For rear wheel skid restraining control, the brake of the front and rear wheels of the outer side of the turn are applied. Also, depending on whether the brake is ON or OFF and the condition of the vehicle, there are circumstances in which the brake might not be applied to the wheels even if those wheels are targeted for braking. The diagram below shows the hydraulic circuit in the pressure increase mode, as it controls the rear wheel skid condition while the vehicle makes a right turn. In other operating modes, the pressure holding valve and the pressure reduction valve are turned ON/OFF according to the ABS with EBD operation pattern.
| *1 | Brake Master Cylinder Sub-assembly | *2 | Brake Actuator Assembly |
| *3 | Master Cylinder Pressure Sensor | *4 | Pump |
| *5 | Pressure Regulator Valves | *6 | Reservoirs |
| *7 | Rear Left Wheel Cylinder | *8 | Rear Right Wheel Cylinder |
| *9 | Front Left Wheel Cylinder | *10 | Front Right Wheel Cylinder |
| Item | VSC Not Activated | VSC Activated | ||||
|---|---|---|---|---|---|---|
| Pressure Increase Mode | Pressure Holding Mode | Pressure Reduction Mode | ||||
|
*: The solenoid valves control the hydraulic pressure by adjusting continually between "open" and "closed" according to the operating conditions. |
||||||
| (1), (2) | Master Cylinder Cut Solenoid Valve | OFF/Open | ON* | ON* | ON* | |
| Port: (A), (B) | ||||||
| Front Brake | (5) | Pressure Holding Valve | OFF/Open | OFF/Open | ON/Closed | ON/Closed |
| Port: (E) | ||||||
| (6) | Pressure Holding Valve | OFF/Open | ON/Closed | ON/Closed | ON/Closed | |
| Port: (F) | ||||||
| (9) | Pressure Reduction Valve | OFF/Closed | OFF/Closed | OFF/Closed | ON/Open | |
| Port: (I) | ||||||
| (10) | Pressure Reduction Valve | OFF/Closed | OFF/Closed | OFF/Closed | OFF/Closed | |
| Port: (J) | ||||||
| Wheel Cylinder Pressure | Right | - | - | - | - | |
| Left | - | Increase | Holding | Reduce | ||
| Rear Brake | (3) | Pressure Holding Valve | OFF/Open | OFF/Open | ON/Closed | ON/Closed |
| Port: (C) | ||||||
| (4) | Pressure Holding Valve | OFF/Open | ON/Closed | ON/Closed | ON/Closed | |
| Port: (D) | ||||||
| (7) | Pressure Reduction Valve | OFF/Closed | OFF/Closed | OFF/Closed | ON/Open | |
| Port: (G) | ||||||
| (8) | Pressure Reduction Valve | OFF/Closed | OFF/Closed | OFF/Closed | OFF/Closed | |
| Port: (H) | ||||||
| Wheel Cylinder Pressure | Right | - | - | - | - | |
| Left | - | Increase | Holding | Reduce | ||
Hill-start Assist Operation
Hill-start assist control operation are performed by closing the master cylinder cut solenoid valves after the driver operates the brake pedal and leaving a certain amount of hydraulic pressure in the wheel cylinder. The diagram below shows the hydraulic circuit in the pressure holding mode.
| *1 | Brake Master Cylinder Sub-assembly | *2 | Brake Actuator Assembly |
| *3 | Master Cylinder Pressure Sensor | *4 | Pump |
| *5 | Pressure Regulator Valves | *6 | Reservoirs |
| *7 | Rear Left Wheel Cylinder | *8 | Rear Right Wheel Cylinder |
| *9 | Front Left Wheel Cylinder | *10 | Front Right Wheel Cylinder |
| Item | Hill-start Assist Control Operation | ||||
|---|---|---|---|---|---|
| Not Activated | Pressure Holding Mode | Pressure Reduction Mode | |||
| (1), (2) | Master Cylinder Cut Solenoid Valve | OFF/Open | ON/Closed | OFF/Open | |
| Port: (A), (B) | |||||
| Front Brake | (5) | Pressure Holding Valve | OFF/Open | OFF/Open | OFF/Open |
| Port: (E) | |||||
| (6) | Pressure Holding Valve | OFF/Open | OFF/Open | OFF/Open | |
| Port: (F) | |||||
| (9) | Pressure Reduction Valve | OFF/Closed | OFF/Closed | OFF/Closed | |
| Port: (I) | |||||
| (10) | Pressure Reduction Valve | OFF/Closed | OFF/Closed | OFF/Closed | |
| Port: (J) | |||||
| Wheel Cylinder Pressure | Right | - | Holding | Reduce | |
| Left | - | Holding | Reduce | ||
| Rear Brake | (3) | Pressure Holding Valve | OFF/Open | OFF/Open | OFF/Open |
| Port: (C) | |||||
| (4) | Pressure Holding Valve | OFF/Open | OFF/Open | OFF/Open | |
| Port: (D) | |||||
| (7) | Pressure Reduction Valve | OFF/Closed | OFF/Closed | OFF/Closed | |
| Port: (G) | |||||
| (8) | Pressure Reduction Valve | OFF/Closed | OFF/Closed | OFF/Closed | |
| Port: (H) | |||||
| Wheel Cylinder Pressure | Right | - | Holding | Reduce | |
| Left | - | Holding | Reduce | ||
Initial Check
After the ignition switch is turned ON (IG), and the vehicle attains an approximate speed of 6 km/h (4 mph) or more, the skid control ECU performs the initial check.
The functions of each solenoid valve and pump motor in the brake actuator assembly are checked in order.