CONSTRUCTION
Models without CAN Communication System
The brake actuator assembly consists of 12 solenoid valves, 2 pressure regulator valves, 2 pumps and 2 reservoirs.
The 12 solenoid valves consist of 2 master cylinder cut solenoid valves [(1), (4)], 2 reservoir cut solenoid valves [(2), (3)], 4 pressure holding solenoid valves [(5), (6), (7), (8)], and 4 pressure reduction solenoid valves [(9), (10), (11), (12)].
| *1 | Brake Master Cylinder Sub-assembly | *2 | Brake Actuator Assembly |
| *3 | Pressure Regulator Valve | *4 | Pump |
| *5 | Reservoir | *6 | Rear Right Wheel Cylinder |
| *7 | Rear Left Wheel Cylinder | *8 | Front Left Wheel Cylinder |
| *9 | Front Right Wheel Cylinder | - | - |
Models with CAN Communication System
A brake actuator assembly integrated with a skid control computer was employed for vehicles with an ABS that uses CAN communication. The brake actuator assembly has a small size and light weight while still having sufficient ejection performance and guarantees excellent safety and running performance even for heavy vehicles.
The brake actuator assembly consists of the actuator, skid control ECU, solenoid relay, pump motor, and master cylinder pressure sensor.
| *a | Actuator Portion | *b | Skid Control ECU |
The actuator portion consists of 10 solenoid valves, 2 pressure regulator valves, 2 pump, 2 reservoirs, and master cylinder pressure sensor.
The 10 solenoid valves consist of 2 master cylinder cut solenoid valves [(1), (2)], 4 pressure holding solenoid valves [(3), (4), (5), (6)], and 4 pressure reduction solenoid valves [(7), (8), (9), (10)].
| *1 | Brake Master Cylinder Sub-assembly | *2 | Brake Actuator Assembly |
| *3 | Master Cylinder Pressure Sensor | *4 | Pump |
| *5 | Pressure Regulator Valves | *6 | Reservoirs |
| *7 | Rear Left Wheel Cylinder | *8 | Rear Right Wheel Cylinder |
| *9 | Front Left Wheel Cylinder | *10 | Front Right Wheel Cylinder |
OPERATION
Models without CAN Communication System
Normal Braking
When the hydraulic pressure of the master cylinder rises, brake fluid is used to transfer hydraulic pressure to the hydraulic circuit of the master cylinder cut solenoid valve, pressure holding solenoid valve and wheel cylinder through the pressure regulator valve.
| *1 | Master Cylinder | *2 | Pump |
| *3 | Reservoir | *4 | Wheel Cylinder |
| Item | Normal Braking | ||
|---|---|---|---|
| Valve | No. | Port | |
| Pressure Regulator Valve | (1) | (A) | Open |
| Master Cylinder Cut Solenoid Valve | (2) | (B) | OFF/Open |
| Reservoir Cut Solenoid Valve | (3) | (C) | OFF/Closed |
| Pressure Holding Solenoid Valve | (4) | (D) | OFF/Open |
| Pressure Reduction Solenoid Valve | (5) | (E) | OFF/Closed |
ABS Operation
Pressure Reduction Mode
When the wheels are about to lock, the pressure holding solenoid valve closes and the pressure reduction solenoid valve opens according to signals from the skid control ECU. As a result, the wheel cylinder brake fluid flows through the pressure reduction solenoid valve to the reservoir, reducing the hydraulic pressure of the wheel cylinder. When ABS is operating, control signals from the skid control ECU are constantly output to the pump. As a result, brake fluid is returned to the master cylinder by the pump.
| *1 | Master Cylinder | *2 | Pump |
| *3 | Reservoir | *4 | Wheel Cylinder |
| Item | Pressure Reduction Mode | ||
|---|---|---|---|
| Valve | No. | Port | |
| Pressure Regulator Valve | (1) | (A) | Open |
| Master Cylinder Cut Solenoid Valve | (2) | (B) | OFF/Open |
| Reservoir Cut Solenoid Valve | (3) | (C) | OFF/Closed |
| Pressure Holding Solenoid Valve | (4) | (D) | ON/Closed |
| Pressure Reduction Solenoid Valve | (5) | (E) | ON/Open |
Pressure Holding Mode
When the hydraulic pressure of the wheel cylinder is increased or decreased to the required hydraulic pressure, the pressure holding solenoid valve and pressure reduction solenoid valve simultaneously close according to control signals from the skid control ECU. As a result, both the master cylinder side and reservoir side circuits are shut and the hydraulic pressure of the wheel cylinder is maintained.
| *1 | Master Cylinder | *2 | Pump |
| *3 | Reservoir | *4 | Wheel Cylinder |
| Item | Pressure Holding Mode | ||
|---|---|---|---|
| Valve | No. | Port | |
| Pressure Regulator Valve | (1) | (A) | Open |
| Master Cylinder Cut Solenoid Valve | (2) | (B) | OFF/Open |
| Reservoir Cut Solenoid Valve | (3) | (C) | OFF/Closed |
| Pressure Holding Solenoid Valve | (4) | (D) | ON/Closed |
| Pressure Reduction Solenoid Valve | (5) | (E) | OFF/Closed |
Pressure Increase Mode
When a sudden increase in the hydraulic pressure of the wheel cylinder is required, the pressure holding solenoid valve opens according to control signals from the skid control ECU. In this case, the system returns to its normal condition and brake fluid is sent from the master cylinder to the wheel cylinder to increase the hydraulic pressure of the wheel cylinder. The speed at which the hydraulic pressure increases is controlled by alternating between pressure increase mode and pressure holding mode.
| *1 | Master Cylinder | *2 | Pump |
| *3 | Reservoir | *4 | Wheel Cylinder |
| Item | Pressure Increase Mode | ||
|---|---|---|---|
| Valve | No. | Port | |
| Pressure Regulator Valve | (1) | (A) | Open |
| Master Cylinder Cut Solenoid Valve | (2) | (B) | OFF/Open |
| Reservoir Cut Solenoid Valve | (3) | (C) | OFF/Closed |
| Pressure Holding Solenoid Valve | (4) | (D) | OFF/Open |
| Pressure Reduction Solenoid Valve | (5) | (E) | OFF/Closed |
Power Assist Brake (PAB) Operation
The valves and pump are operated according to control signals from the skid control ECU, sending hydraulic pressure to the wheel cylinders and generating hydraulic pressure greater than that of the master cylinder.
| *A | Except when Brake Booster Negative Pressure has Decreased | *B | When Brake Booster Negative Pressure has Decreased |
| *1 | Master Cylinder | *2 | Pump |
| *3 | Reservoir | *4 | Wheel Cylinder |
| Item | Except when Brake Booster Negative Pressure has Decreased | When Brake Booster Negative Pressure has Decreased | ||
|---|---|---|---|---|
| Valve | No. | Port | ||
| Pressure Regulator Valve | (1) | (A) | Closed | Open |
| Master Cylinder Cut Solenoid Valve | (2) | (B) | OFF/Open | ON/Closed |
| Reservoir Cut Solenoid Valve | (3) | (C) | ON/Open | ON/Open |
| Pressure Holding Solenoid Valve | (4) | (D) | OFF/Open | OFF/Open |
| Pressure Reduction Solenoid Valve | (5) | (E) | OFF/Closed | OFF/Closed |
Initial Check
After the ignition switch is turned ON (IG), and the vehicle attains an approximate speed of 6 km/h (4 mph) or more, the skid control ECU performs the initial check.
The functions of each solenoid valve and pump motor in the brake actuator assembly are checked in order.
Models with CAN Communication System
ABS with EBD Operation
Based on the signals received from the 4 wheel speed sensors and yaw rate and deceleration sensor, the skid control ECU calculates the wheel rotation speed and deceleration for each wheel, in order to check for a wheel slippage condition. According to the slippage condition, the ECU controls the pressure holding solenoid valves and pressure reduction solenoid valves in order to adjust the fluid pressure of the brakes for each of the wheels in the following 3 modes: pressure reduction, pressure holding, and pressure increase modes.
Power Assist Brake (PAB) Operation
In certain situations when the vacuum pressure of the vacuum booster calculated using the vacuum sensor and master cylinder pressure sensor is low, the skid control ECU may provide brake assist. Or in the event of a brake booster failure, based on the brake pedal load sensing switch and master cylinder pressure sensor signal, the skid control ECU may provide brake assist.
If the skid control ECU judges the need for additional brake assist, pressure is generated by the pump in the brake actuator and directed to the wheel cylinder to apply a large amount of fluid pressure.
| *1 | Brake Master Cylinder Sub-assembly | *2 | Brake Actuator Assembly |
| *3 | Master Cylinder Pressure Sensor | *4 | Pump |
| *5 | Pressure Regulator Valves | *6 | Reservoirs |
| *7 | Rear Left Wheel Cylinder | *8 | Rear Right Wheel Cylinder |
| *9 | Front Left Wheel Cylinder | *10 | Front Right Wheel Cylinder |
| Item | Power Assist Brake (PAB) Not Activated | Power Assist Brake (PAB) Activated | |
|---|---|---|---|
|
*: The solenoid valves control the hydraulic pressure by adjusting continually between "open" and "closed" according to the operating conditions. |
|||
| (1), (2) | Master Cylinder Cut Solenoid Valve | OFF/Open | ON* |
| Port: (A), (B) | |||
| (3), (4), (5), (6) | Pressure Holding Solenoid Valve | OFF/Open | OFF/Open |
| Port: (C), (D), (E), (F) | |||
| (7), (8), (9), (10) | Pressure Reduction Solenoid Valve | OFF/Closed | OFF/Closed |
| Port: (G), (H), (I), (J) | |||
Brake Assist Operation
In the event of emergency braking, the skid control ECU determines the driver's intention based on the speed of the pressure increase in the master cylinder determined by the master cylinder pressure sensor signal. If the skid control ECU determines the need for additional brake assist, pressure is generated by the pump in the brake actuator assembly and directed to the wheel cylinder to apply a large amount of fluid pressure.
| *1 | Brake Master Cylinder Sub-assembly | *2 | Brake Actuator Assembly |
| *3 | Master Cylinder Pressure Sensor | *4 | Pump |
| *5 | Pressure Regulator Valves | *6 | Reservoirs |
| *7 | Rear Left Wheel Cylinder | *8 | Rear Right Wheel Cylinder |
| *9 | Front Left Wheel Cylinder | *10 | Front Right Wheel Cylinder |
| Item | Brake Assist Not Activated | Brake Assist Activated | |
|---|---|---|---|
|
*: The solenoid valves control the hydraulic pressure by adjusting continually between "open" and "closed" according to the operating conditions. |
|||
| (1), (2) | Master Cylinder Cut Solenoid Valve | OFF/Open | ON* |
| Port: (A), (B) | |||
| (3), (4), (5), (6) | Pressure Holding Solenoid Valve | OFF/Open | OFF/Open |
| Port: (C), (D), (E), (F) | |||
| (7), (8), (9), (10) | Pressure Reduction Solenoid Valve | OFF/Closed | OFF/Closed |
| Port: (G), (H), (I), (J) | |||
Initial Check
After the ignition switch is turned ON (IG), and the vehicle attains an approximate speed of 6 km/h (4 mph) or more, the skid control ECU performs the initial check.
The functions of each solenoid valve and pump motor in the brake actuator assembly are checked in order.