Home › Engine / Hybrid System › N04C-UH (ENGINE CONTROL) › ECD SYSTEM
NM2850E _51 Engine / Hybrid System _074214 N04C-UH ENGINE CONTROL _0361388 ECD SYSTEM CO CONTROL F

N04C-UH ENGINE CONTROL  ECD SYSTEM  CONTROL  TURBOCHARGER CONTROL  


FUNCTION


a.

The engine ECU controls the nozzle vane position using the turbo motor driver, in order to obtain the calculated target turbo pressure appropriate to the engine operating conditions.


b.

The turbo motor driver detects the actual nozzle vane position and provides feedback to the engine ECU. The engine ECU calculates the optimal nozzle vane position in accordance with the driving conditions (engine speed, injection volume, atmospheric pressure, and water temperature, etc.), and sends a target nozzle vane position signal to the turbo motor driver. The turbo motor driver controls the nozzle vane position in accordance with this signal and the actual nozzle vane position.

W141061C01
1.156,1.448 0.813,0.896 true 4.198,0.594 3.948,1.052 true 0.656,0.729 0.969,0.958 0.313,0.229 10 false *1 4.177,0.385 4.49,0.708 0.313,0.323 10 false *2 5.229,2.448 5.542,2.76 0.313,0.313 10 false *3 5.26,1.646 5.563,1.896 0.302,0.25 10 false *4 6.198,1.49 6.521,1.771 0.323,0.281 10 false *5 6.208,2.115 6.521,2.396 0.313,0.281 10 false *6 6.219,2.74 6.51,2.979 0.292,0.24 10 false *7 6.208,3.375 6.531,3.625 0.323,0.25 10 false *8
*1 Turbo Motor Driver and DC Motor (Nozzle Vane Position Control) *2 Turbo Pressure Sensor
*3 Engine ECU *4 Atmospheric Pressure Sensor
*5 Crankshaft Position Sensor *6 Injector
*7 Water Temperature Sensor *8 Intake Air Temperature Sensor
V100159

CAN (V Bus) - -




OPERATION


a.

In Low Speed Range

i.

When the engine is running in a low speed range, the DC motor presses down the linkage with a signal from the turbo motor driver. The tip of the linkage rotates the unison ring counterclockwise through a drive arm.


ii.

The unison ring contains a driven arm, which is placed through the cutout portion of the unison ring. This driven arm also moves in the direction of the rotation of the unison ring. The fulcrum of the driven arm is an axis that is integrated with the nozzle vane behind the plate. When the driven arm moves counterclockwise, the nozzle vane moves toward the closing direction. This results in an increasing in the velocity of the exhaust gas flowing to the turbine, as well as the speed of the turbine. As a result, torque is improved when the engine is running at low speeds.

W141062C01
0.333,1.104 0.792,1.104 true 0.604,2.115 1.146,1.865 true 2.521,2.396 3.156,2.573 true 2.99,2.146 3.552,2.25 true 2.958,0.792 3.438,0.531 true 4.156,0.583 4.552,0.906 true 4.688,0.313 5.104,0.771 true 6.094,0.302 5.688,0.76 true 0.125,1.031 0.448,1.323 0.323,0.292 10 false *1 0.427,2.073 0.802,2.313 0.375,0.24 10 false *2 3.198,2.542 3.448,2.76 0.25,0.219 10 false *3 3.594,2.188 3.865,2.417 0.271,0.229 10 false *4 3.49,0.438 3.802,0.656 0.313,0.219 10 false *5 4,0.417 4.302,0.646 0.302,0.229 10 false *6 4.542,0.167 4.854,0.417 0.313,0.25 10 false *7 6.094,0.125 6.406,0.354 0.313,0.229 10 false *8
*1 Linkage *2 Drive Arm
*3 Driven Arm *4 Cutout Portion
*5 Unison Ring *6 Plate
*7 Fulcrum *8 Nozzle Vane




b.

In Medium-to-High Speed Range

i.

When the engine is running in a medium-to-high speed range, the DC motor pulls up the linkage with a signal from the turbo motor driver. With this, the driven arm moves clockwise and this opens the nozzle vane and maintains the specified supercharging pressure. Thus, the back pressure is lowered and the output and fuel consumption are improved.

W141063