Home › Engine / Hybrid System › N04C-UH (INTAKE / EXHAUST) › INTAKE SYSTEM
NM2850E _51 Engine / Hybrid System _074218 N04C-UH INTAKE / EXHAUST _0369127 INTAKE SYSTEM DE DETAILS F

N04C-UH INTAKE / EXHAUST  INTAKE SYSTEM  DETAILS  TURBOCHARGER  


CONSTRUCTION


A variable nozzle vane type turbocharger, which has a small-diameter turbine and which is made by Honeywell (Garrett brand), is used to improve the efficiency of the system.


a.

Variable Nozzle Vane Type Turbocharger

i.

The variable nozzle vane type turbocharger consists primarily of a turbine wheel, compressor wheel, nozzle vane, unison ring, linkage, DC motor and turbo motor driver. The DC motor and turbo motor driver are integrated.


ii.

This turbocharger has realized great improvements in low-speed torque, maximum output, fuel consumption, and emission reduction. These improvements have been accomplished through variable control of the nozzle vane position, and an optimal velocity for the exhaust gas inflow to the turbine wheel at all times in response to the engine condition.


iii.

The engine ECU outputs a signal to the turbo motor driver, which actuates the DC motor, to control the nozzle vane position. Also, the turbo motor driver detects the position of the nozzle vane.

W141017C01
2.156,1.385 2.479,0.896 true 2.073,2.271 2.917,2.531 true 1.646,3.385 2.333,3.979 true 3.865,1.25 4.354,0.698 true 3.458,1.344 3.042,1.01 true 3.781,1.74 4.688,1.083 true 5.969,2.729 6.375,2.104 true 4.677,4.208 5.344,3.323 true 2.49,0.698 2.854,0.948 0.365,0.25 10 false *1 2.979,2.5 3.281,2.76 0.302,0.26 10 false *2 2.385,4 2.729,4.281 0.344,0.281 10 false *3 2.875,0.854 3.208,1.156 0.333,0.302 10 false *4 4.396,0.552 4.76,0.792 0.365,0.24 10 false *5 4.708,0.948 4.979,1.188 0.271,0.24 10 false *6 4.5,4.198 4.958,4.458 0.458,0.26 10 false *7 6.365,1.927 6.635,2.167 0.271,0.24 10 false *6
*1 Turbine *2 Linkage
*3 Turbo Motor Driver and DC Motor *4 Unison Ring
*5 Drive Arm *6 Nozzle Vane
*7 Turbine Wheel - -



iv.

The exhaust gas from the exhaust manifold goes through the nozzle vane inside the turbocharger housing, and flows to the exhaust pipe through the turbine wheel. The speed of the turbine wheel (supercharging pressure) differs depending on the flow velocity of the exhaust gas going through the turbine wheel and the flow velocity of the exhaust gas is controlled by the opening angle of the nozzle vane. At times like during idling, when the exhaust gas is reduced, the nozzle vanes are almost fully closed, but as there is a slight clearance between the nozzle vanes, the exhaust gas flows through this clearance to the exhaust pipe. As the nozzle vanes of this type of turbocharger can move in this way, there is no need for bypassing as with the conventional type turbocharger.

W141018C01
2.823,2.063 3.542,1.531 true 4.573,1.104 5.094,0.646 true 4.521,1.792 5.146,2.281 true 2.635,2.052 2.979,2.333 0.344,0.281 10 false *1 5.156,0.51 5.51,0.781 0.354,0.271 10 false *2 5.198,2.313 5.583,2.542 0.385,0.229 10 false *3
*1 Compressor Wheel *2 Turbine Wheel
*3 Nozzle Vane - -
V100135

Exhaust Gas
V100136

Intake Air