Home › Engine / Hybrid System › N04C-UH (ENGINE CONTROL) › ECD SYSTEM
NM2850E _51 Engine / Hybrid System _074214 N04C-UH ENGINE CONTROL _0361388 ECD SYSTEM CO CONTROL F

N04C-UH ENGINE CONTROL  ECD SYSTEM  CONTROL  SUPPLY PUMP CONTROL  


CONSTRUCTION


a.

The drive force of the pump outputs in the following order: the crankshaft, the idle gears, the gear that is attached to the front of the pump, and the ring cam.


b.

The supply pump consists of four portions: a pump body to pump pressurized fuel, a discharge check valve to regulate the fuel flow rate, a suction control valve to regulate the fuel pressure at the inlet to the inhale check valve, and a feed pump to supply fuel to the pump body. The supply pump draws an appropriate amount of fuel and feeds pressurized fuel into the common-rail.


c.

The eccentric cam alternately moves two plungers via the ring cam.


d.

The two plungers are horizontally opposed, so when one plunger is in a suction stroke, the other is in a pumping stroke. The two plungers repeat these strokes in order to ensure a constant and stable delivery of fuel.

W141027C01
2.531,2.448 3.698,1.177 true 2.365,2.469 2.698,2.688 0.333,0.219 10 false *1
*1 SCV (Suction Control Valve) - -


W141029C01
2.875,0.313 3.813,0.708 true 3.844,0.271 4,0.125 4,0.125 4.167,0.125 true 4.042,0.563 4.76,0.208 true 3.875,1.104 5.313,1.01 5.313,1.01 3.875,1.542 true 4.458,1.531 5.24,2.083 true 3.854,2.51 3.99,2.677 3.99,2.677 4.156,2.677 true 2.958,2.573 3.813,2.031 true 2.51,1.917 3.219,1.458 true 2.542,0.823 3.74,1.271 true 2.677,0.219 3.021,0.448 0.344,0.229 10 false *1 2.344,0.698 2.729,0.969 0.385,0.271 10 false *2 2.333,1.896 2.667,2.167 0.333,0.271 10 false *3 4.208,2.583 4.438,2.76 0.229,0.177 10 false *4 5.302,2.063 5.656,2.302 0.354,0.24 10 false *5 5.365,0.917 5.719,1.25 0.354,0.333 10 false *6 4.823,0.083 5.104,0.313 0.281,0.229 10 false *7 4.208,0.042 4.438,0.219 0.229,0.177 10 false *4 2.781,2.563 3.125,2.792 0.344,0.229 10 false *1
*1 Plunger *2 Eccentric Cam
*3 Eccentric Camshaft *4 Inhale Check Valve
*5 Feed Pump *6 Ring Cam
*7 Discharge Check Valve - -



e.

The engine ECU determines the target fuel pressure based on the load condition.


f.

The engine ECU adjusts the SCV opening angle by the duty control function to reach the target fuel pressure.

W141028C01
1.292,0.865 1.635,0.979 true 2.458,0.573 2.479,0.958 true 3.99,0.531 4.531,0.448 true 4.021,0.885 4.573,0.854 true 3.979,1.271 4.573,1.385 true 1.094,0.76 1.417,1.063 0.323,0.302 10 false *1 2.365,0.375 2.688,0.604 0.323,0.229 10 false *2 4.594,0.344 4.948,0.563 0.354,0.219 10 false *3 4.615,0.771 4.885,0.969 0.271,0.198 10 false *4 2.031,0.708 2.271,0.917 0.24,0.208 10 false *a 2.635,1.469 2.927,1.688 0.292,0.219 10 false *b 5.531,0.833 5.844,1.135 0.313,0.302 10 false *c 4.615,1.323 4.969,1.542 0.354,0.219 10 false *3
*1 Engine ECU *2 SCV
*3 Plunger *4 Cam
*a Duty Control *b Fuel (From Fuel Tank)
*c Fuel (To Common-rail) - -




OPERATION


a.

Small Opening of Suction Control Valve

i.

When the opening of the suction control valve is small, the fuel suction passage narrows and slows down the fuel flow.


ii.

Even if the plunger reaches its maximum stroke, the volume of fuel drawn in by the plunger becomes restricted because the fuel suction passage is restricted. (See "B" in the diagram.)


iii.

The supply pump discharges fuel when the cam pushes the plunger upward and the fuel discharge pressure becomes higher than the fuel pressure in the common-rail. (See "C" in the diagram.)

W141030C01
1.177,2.313 1.958,2.156 true 1.167,2.844 1.875,2.625 true 1.156,1.635 1.438,1.813 0.281,0.177 10 false *1 0.969,2.24 1.323,2.521 0.354,0.281 10 false *2 0.99,2.802 1.406,3.167 0.417,0.365 10 false *3 1.76,1.365 2.073,1.625 0.313,0.26 10 false *a 3.375,1.396 3.688,1.604 0.313,0.208 10 false *b 4.365,1.406 4.646,1.656 0.281,0.25 10 false *c 0.99,0.833 1.333,1.073 0.344,0.24 10 false *d 5.885,0.26 6.313,0.552 0.427,0.292 10 false : *e 1.896,3.031 2.208,3.292 0.313,0.26 10 false *a 3.5,3.083 3.813,3.292 0.313,0.208 10 false *b 5.115,3.094 5.396,3.344 0.281,0.25 10 false *c
*1 SCV *2 Plunger
*3 Cam - -
*a Plunger Top-Dead-Center *b Plunger Bottom-Dead-Center
*c Compression Starting Point *d Plunger Stroke
*e Fuel Suction Volume - -




b.

Large Opening of Suction Control Valve

i.

When the opening of the suction control valve is large, the fuel suction passage widens and facilitates the fuel flow.


ii.

When the plunger reaches its maximum stroke, the plunger draws an ample volume of fuel because the fuel suction passage is not restricted. (See "B" in the diagram.)


iii.

The supply pump discharges fuel when the cam pushes the plunger upward and the fuel discharge pressure becomes higher than the fuel pressure in the common-rail. (See "C" in the diagram.)

W141031C01
1.125,2.979 1.604,2.719 true 1.042,2.365 1.698,2.292 true 0.906,1.688 1.135,1.896 0.229,0.208 10 false *1 0.854,2.313 1.177,2.583 0.323,0.271 10 false *2 0.917,2.969 1.25,3.271 0.333,0.302 10 false *3 1.542,3.135 1.865,3.354 0.323,0.219 10 false *a 3.469,3.167 3.781,3.385 0.313,0.219 10 false *b 5.354,3.156 5.667,3.385 0.313,0.229 10 false *c 0.677,0.885 0.948,1.135 0.271,0.25 10 false *d 5.688,0.302 6.125,0.625 0.438,0.323 10 false : *e 1.396,1.427 1.719,1.646 0.323,0.219 10 false *a 3.083,1.427 3.396,1.646 0.313,0.219 10 false *b 3.406,1.427 3.719,1.656 0.313,0.229 10 false *c
*1 SCV *2 Plunger
*3 Cam - -
*a Plunger Top-Dead-Center *b Plunger Bottom-Dead-Center
*c Compression Starting Point *d Plunger Stroke
*e Fuel Suction Volume - -