Home › Engine / Hybrid System › N04C-VQ ENGINE CONTROL › ECD SYSTEM
NM2850E _51 Engine / Hybrid System _074231 N04C-VQ ENGINE CONTROL _0361389 ECD SYSTEM CO CONTROL F

N04C-VQ ENGINE CONTROL  ECD SYSTEM  CONTROL  SUPPLY PUMP CONTROL  


FUNCTION


a.

The ECM determines the target fuel pressure based on the load condition.


b.

The ECM adjusts the SCV opening angle by the duty control function to reach the target fuel pressure.

W141028C01
1.292,0.865 1.635,0.979 true 2.458,0.573 2.479,0.958 true 3.99,0.531 4.531,0.448 true 4.021,0.885 4.573,0.854 true 3.979,1.271 4.573,1.385 true 1.094,0.76 1.417,1.063 0.323,0.302 10 false *1 2.365,0.375 2.688,0.604 0.323,0.229 10 false *2 4.594,0.344 4.948,0.563 0.354,0.219 10 false *3 4.615,0.771 4.885,0.969 0.271,0.198 10 false *4 2.031,0.708 2.271,0.917 0.24,0.208 10 false *a 2.635,1.469 2.927,1.688 0.292,0.219 10 false *b 5.531,0.833 5.844,1.135 0.313,0.302 10 false *c 4.615,1.323 4.969,1.542 0.354,0.219 10 false *3
*1 ECM *2 SCV
*3 Plunger *4 Cam
*a Duty Control *b Fuel (from Diesel Fuel Filter Assembly)
*c Fuel (to Common-rail Assembly) - -




OPERATION


a.

Small Opening of Suction Control Valve

i.

When the opening of the suction control valve is small, the fuel suction passage narrows and slows down the fuel flow.


ii.

Even if the plunger reaches its maximum stroke, the volume of fuel drawn in by the plunger becomes restricted because the fuel suction passage is restricted. (See "B" in the diagram.)


iii.

The injection or supply pump assembly discharges fuel when the cam pushes the plunger upward and the fuel discharge pressure becomes higher than the fuel pressure in the common-rail assembly. (See "C" in the diagram.)

W141030C01
1.177,2.313 1.958,2.156 true 1.167,2.844 1.875,2.625 true 1.156,1.635 1.438,1.813 0.281,0.177 10 false *1 0.969,2.24 1.323,2.521 0.354,0.281 10 false *2 0.99,2.802 1.406,3.167 0.417,0.365 10 false *3 1.76,1.365 2.073,1.625 0.313,0.26 10 false *a 3.375,1.396 3.688,1.604 0.313,0.208 10 false *b 4.365,1.406 4.646,1.656 0.281,0.25 10 false *c 0.99,0.833 1.333,1.073 0.344,0.24 10 false *d 5.885,0.26 6.313,0.552 0.427,0.292 10 false : *e 1.896,3.031 2.208,3.292 0.313,0.26 10 false *a 3.5,3.083 3.813,3.292 0.313,0.208 10 false *b 5.115,3.094 5.396,3.344 0.281,0.25 10 false *c
*1 SCV *2 Plunger
*3 Cam - -
*a Plunger Top-Dead-Center *b Plunger Bottom-Dead-Center
*c Compression Starting Point *d Plunger Stroke
*e Fuel Suction Volume - -




b.

Large Opening of Suction Control Valve

i.

When the opening of the suction control valve is large, the fuel suction passage widens and facilitates the fuel flow.


ii.

When the plunger reaches its maximum stroke, the plunger draws an ample volume of fuel because the fuel suction passage is not restricted. (See "B" in the diagram.)


iii.

The injection or supply pump assembly discharges fuel when the cam pushes the plunger upward and the fuel discharge pressure becomes higher than the fuel pressure in the common-rail assembly. (See "C" in the diagram.)

W141031C01
1.125,2.979 1.604,2.719 true 1.042,2.365 1.698,2.292 true 0.906,1.688 1.135,1.896 0.229,0.208 10 false *1 0.854,2.313 1.177,2.583 0.323,0.271 10 false *2 0.917,2.969 1.25,3.271 0.333,0.302 10 false *3 1.542,3.135 1.865,3.354 0.323,0.219 10 false *a 3.469,3.167 3.781,3.385 0.313,0.219 10 false *b 5.354,3.156 5.667,3.385 0.313,0.229 10 false *c 0.677,0.885 0.948,1.135 0.271,0.25 10 false *d 5.688,0.302 6.125,0.625 0.438,0.323 10 false : *e 1.396,1.427 1.719,1.646 0.323,0.219 10 false *a 3.083,1.427 3.396,1.646 0.313,0.219 10 false *b 3.406,1.427 3.719,1.656 0.313,0.229 10 false *c
*1 SCV *2 Plunger
*3 Cam - -
*a Plunger Top-Dead-Center *b Plunger Bottom-Dead-Center
*c Compression Starting Point *d Plunger Stroke
*e Fuel Suction Volume - -