Home › Power Source / Network › NETWORKING › MULTIPLEX COMMUNICATION SYSTEM › from 2019.08
NM2850E _57 Power Source / Network _074169 NETWORKING _0361175 MULTIPLEX COMMUNICATION SYSTEM GE GENERAL F

NETWORKING  MULTIPLEX COMMUNICATION SYSTEM  GENERAL  GENERAL  


OUTLINE


a.

The multiplex communication system has been adopted for the some models.


b.

The multiplex communication system uses the following communication protocol:

i.

The Controller Area Network (CAN) is used for communication between the engine, chassis and body electrical system.



c.

The CAN has 2 types, with different communication speeds: the HS-CAN (high speed) and the MS-CAN (medium speed)*.

*: Models with UREA Selective Catalytic Reduction (SCR) system



d.

The central gateway ECU (network gateway ECU) and translate ECU assembly* are used as gateways to transmit data between the buses.

*: Models with UREA Selective Catalytic Reduction (SCR) system




MAIN FEATURES


a.

Multiplex communication uses serial communication data that consists of bits and frames in order to exchange information between the various ECUs. This allows a reduction of the amount of wiring used in the vehicle.

i.

A bit is the basic unit of communication used to represent the information. A bit is represented by binary values of "0" or "1".


ii.

A frame is a body of data transmitted together. A frame contains a header that indicates the beginning, and an end message that indicates the end.

Conceptual Drawing
Y233532E01
0.063,0.719 1.802,1 1.74,0.281 10 false Serial Communication Data 1.844,0.521 2,0.729 0.156,0.208 10 false 1 1.854,0.938 2.01,1.146 0.156,0.208 10 false 0 2.281,1.271 2.802,1.531 0.521,0.26 10 false Header 2.281,1.271 2.802,1.531 0.521,0.26 10 false Header 3.594,0.76 4.115,1.021 0.521,0.26 10 false Data 4.729,1.26 5.646,1.5 0.917,0.24 10 false End Message 3.563,1.813 4.083,2.073 0.521,0.26 10 false Frame 0.417,3.281 0.938,3.542 0.521,0.26 10 false Battery 1.844,4.031 2.365,4.292 0.521,0.26 10 false Switch 2.5,3.229 2.854,3.458 0.354,0.229 10 false ECU 4.583,3.24 4.938,3.469 0.354,0.229 10 false ECU 3.073,2.719 3.427,2.948 0.354,0.229 10 false On 3.063,3.115 3.417,3.344 0.354,0.229 10 false Off 6.26,3.031 6.938,3.271 0.677,0.24 10 false Motor 6.26,2.594 6.938,2.833 0.677,0.24 10 false Light 6.271,3.427 6.948,3.667 0.677,0.24 10 false Heater 6.26,3.833 6.938,4.073 0.677,0.24 10 false Solenoid



b.

CAN Type

i.

The CAN protocol is the rule for establishing data communication. If the ECUs in the network use different frameworks for their data, such as communication speed, communication wire, and signals, they will be unable to understand each other. Therefore, a protocol (rule) must be established among them.


ii.

The CAN is able to transmit larger amounts of data faster than other protocols. This feature makes it possible to transmit data accurately in the engine, chassis and body electrical system, which requires large amounts of data to be transmitted in short periods of the time.

Protocol CAN (HS-CAN) CAN (MS-CAN)
Communication Speed 500 kbps* 250 kbps*
Communication Wire Twisted-pair Wire
Drive Type Differential Voltage Drive
Data Length 1-8 Bytes (Variable)

HINT:

*: bps is an abbreviation of "Bits Per Second", indicating the number of bits that can be transmitted per second.




c.

Communication Wire

i.

A twisted pair of wires is used for CAN communication.

Communication Wire Outline
Twisted-pair Wire
Y120996

This communication wire is a pair of twisted wires. Communication is driven by applying different voltages to the 2 lines in order to send a single signal. This system, which is called a "Differential Voltage Drive", reduces noise.

Y211516E02
1.813,1.333 2.177,1.531 0.365,0.198 10 false ECU 5.073,1.323 5.417,1.573 0.344,0.25 10 false ECU 3.094,1.531 4.292,1.833 1.198,0.302 10 false Twisted-pair Wire 2.865,2.156 4.458,2.521 1.594,0.365 10 false Differential Voltage Drive