Home › Drivetrain › A861E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM › from 2019.08
NM2850E _52 Drivetrain _083616 A861E AUTOMATIC TRANSMISSION / TRANSAXLE _0406493 AUTOMATIC TRANSMISSION SYSTEM CO CONTROL F

A861E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  CONTROL  AUTOMATIC TRANSMISSION CONTROL  


FUNCTION OF MAIN COMPONENTS


Component Function
Transmission Solenoid S1 Performs connection switching to each clutch/brake for the line pressure/control pressure.
Transmission Solenoid S2
Transmission Solenoid S3
Transmission Solenoid S4
Linear Solenoid SL1 Controls the clutch hydraulic pressure.
Linear Solenoid SL2 Controls the clutch/brake hydraulic pressure.
Linear Solenoid SL3 Controls the clutch/brake hydraulic pressure or the lock-up pressure.
Linear Solenoid SL4 Performs line pressure control.
No. 1 Oil Pressure Switch Detects the control hydraulic pressure of linear solenoid SL1.
No. 2 Oil Pressure Switch Detects the control hydraulic pressure of linear solenoid SL2.
No. 3 Oil Pressure Switch Detects the control hydraulic pressure of transmission solenoid S1.
No. 4 Oil Pressure Switch Detects the control hydraulic pressure of transmission solenoid S2.
No. 5 Oil Pressure Switch Detects the control hydraulic pressure of transmission solenoid S3.
No. 6 Oil Pressure Switch Detects the control hydraulic pressure of transmission solenoid S4.
No. 7 Oil Pressure Switch Detects the control hydraulic pressure of linear solenoid SL3.
No. 8 Oil Pressure Switch Detects the line hydraulic pressure.
Speed Sensor Sends wheel speed signals to the skid control ECU.
Temperature Sensor Detects the temperature inside the transmission hydraulic pressure control circuit.
ATF Temperature Sensor (Transmission Wire)
Stop Light Switch Assembly Detects the brake pedal depressing signal.
Park/Neutral Position Switch Assembly Detects the shift lever position.
O/D Switch (Transmission Control Switch) Switches the O/D switch (transmission control switch) on/off.
Transmission Revolution Sensor (NC) Detects the output speed of the transmission.
Speed Sensor (NT) Detects the turbine rotation axis of the torque converter assembly.
First Hold Switch (No. 1 Pattern Select Switch Assembly) Fixes the gear to 1st gear when this switch is turned on with the shift lever position in "2/L".
Exhaust Brake Switch (Windshield Wiper Switch Assembly) Switches the exhaust brake on/off.
Combination Meter Assembly Speedometer Sends wheel speed signals to the transmission control ECU.
Shift Position Indicator Notifies the driver of the current shift position by displaying an indicator.
O/D OFF Indicator Light
·

Notifies the driver that the O/D switch (transmission control switch) is off by turning the indicator on.

·

Notifies the driver that the transmission control ECU has detected a malfunction in the system by blinking the indicator.


Exhaust Brake Indicator Light Notifies the driver that the exhaust brake switch (windshield wiper switch assembly) is on by turning the indicator on.
Brake Actuator Assembly Skid Control ECU Sends wheel speed signals to the speedometer.
Transmission control ECU Performs transmission control based on signals from each sensor.
ECM
·

Sends engine speed signals to the transmission control ECU.

·

Sends throttle opening angle signal to transmission control ECU via translate ECU Assembly.


Translate ECU Assembly Relays CAN communication signals.
Central Gateway ECU (Network Gateway ECU)
DLC3 DTCs and ECU data can be read by connecting and operating a diagnostic tool.


SYSYTEM CONTROL


a.

Shifting and Lock-up Control

i.

Shifting point control and lock-up control are performed based on the shift position, vehicle speed, throttle opening angle and driving conditions.

Shift Positions and Shift Position/Lock-up Patterns
Shift Range D (O/D Switch (Transmission Control Switch) Shifting/Lock-up Pattern
D OFF 1st←→2nd←→3rd←→4th←→5th*←→6th*
D ON 1st←→2nd←→3rd←→4th←→5th*
4 - 1st←→2nd←→3rd←→4th
2/L - 1st←→2nd

HINT:

*: Lock-up Control




b.

First Hold Control

i.

When the shift lever is moved to "2/L" and the first hold switch (No. 1 pattern select switch assembly) provided in the center console is turned on, the shift range is fixed to 1st gear.

Shifting Patterns (with Shift Lever in "2/L")
First Hold Switch (No. 1 Pattern Select Switch Assembly) Shifting Patterns
OFF 1st←→2nd
ON Fixed to 1st gear

First Hold Control Release Condition
Release Condition
When the shift range is other than "2/L".
When the shift range is "2/L" and the first hold switch is turned off.
Ignition switch off.



c.

Deceleration Control

i.

Deceleration control is used to optimize the engine brake force when the exhaust brake is on.


ii.

When the exhaust brake is on, high accuracy vehicle weight estimation and road grade estimation are performed. Downshifting is performed automatically based on changes in vehicle weight, the road grade and the vehicle speed to ensure engine brake force.


iii.

Deceleration control is released when the exhaust brake is turned off.

Deceleration Control Operation Conditions
conditions
Exhaust brake on.
When driving from 6th gear to 4th gear with the D range selected.
When a downshift requests is generated based on the shift position determination map (determined from the vehicle weight, road grade and vehicle speed).




FAIL-SAFE


a.

This function minimizes the loss of operability when a malfunction occurs in the sensors or solenoids.


b.

For details, refer to the Repair Manual.



DIAGNOSIS


a.

When a malfunction is detected due to signals from sensors, the O/D OFF indicator light in the combination meter assembly is turned on to warn the driver.


b.

The diagnostic tool can now be used to perform failure diagnosis for the entire vehicle.