Home › Vehicle Interior › METER / GAUGE / DISPLAY › COMBINATION METER › from 2021.01
NM2850E _58 Vehicle Interior _074159 METER / GAUGE / DISPLAY _0361244 COMBINATION METER DE DETAILS F

METER / GAUGE / DISPLAY  COMBINATION METER  DETAILS  COMBINATION METER  


CONSTRUCTION


a.

Multi-information Display (Models with Analog Type Combination Meter Assembly with Multi-information Display)

i.

The multi-information display has 2 areas depending on the display mode.

Y226484C01
5.667,1.25 5.5,0.917 true 5.667,1.667 5.5,2 true 1.635,2.302 1.875,1.885 true 2.792,1.885 3.094,2.323 true 1.542,2.333 1.854,2.49 0.313,0.156 10 false *1 3.073,2.354 3.385,2.51 0.313,0.156 10 false *2 4.719,0.656 5.031,0.813 0.313,0.156 10 false *3 5.385,0.729 5.698,0.885 0.313,0.156 10 false *4 5.427,2.031 5.74,2.188 0.313,0.156 10 false *5
*1 DISP Switch *2 ODO/TRIP Switch
*3 Multi-information Display *4 Drive Information Display
*5 ODO/TRIP Meter - -



ii.

The drive information display changes in the order shown below by pressing the DISP switch.


iii.

The average fuel consumption value can be reset by pressing and holding the DISP switch for 0.8 seconds or more.

Flow of Drive Information Display
Y226485C01
0.583,1.167 1,1.333 0.417,0.167 10 false *a (*f) 2.917,1.167 3.167,1.333 0.25,0.167 10 false *b 5.167,1.167 5.417,1.333 0.25,0.167 10 false *c 4,2.417 4.25,2.583 0.25,0.167 10 false *d 1.75,2.417 2,2.583 0.25,0.167 10 false *e
*a Average Fuel Consumption *b Average Vehicle Speed
*c Driving Time *d Cruising Range
*e Outside Temperature *f Pressing DISP switch for 0.8 seconds or more to reset.
V100136

Pressing DISP switch for less than 0.8 seconds. - -


HINT:

The illustrations shown are examples only. The illustrations may differ the actual vehicle screen.



iv.

The ice warning light was provided on the multi-information display.


v.

When the outside temperature drops below 3 °C, an ice warning light flashes 10 times to warn the driver to drive with caution due to icy road conditions. After the ice warning light flashes 10 times, the light stays on.


vi.

When the outside temperature reaches 5 °C, the light goes off.

Y226486C01
1.063,0.667 1.563,0.823 true 0.875,0.563 1.188,0.719 0.313,0.156 10 false *1 1.333,1.333 1.583,1.5 0.25,0.167 10 false *a 4,1.333 4.25,1.583 0.25,0.25 10 false *b
*1 Ice Warning Light - -
*a Outside Temperature Display *b Except Outside Temperature Display



vii.

The ODO/TRIP meter display changes in the order shown below by pressing the ODO/TRIP switch.


viii.

The meter panel luminance adjustment mode is also displayed when the taillight is on.


ix.

While the meter panel luminance adjustment mode is displayed, the brightness of the meter can be changed by pressing ODO/TRIP switch for 1 second or more. The brightness of the meter can be adjusted in 4 levels.

Flow of the ODO/TRIP Meter
Y246595C01
1.552,0.917 1.802,1.083 0.25,0.167 10 false *a 3.51,0.917 3.917,1.167 0.406,0.25 10 false *b (*i) 5.375,0.917 5.802,1.177 0.427,0.26 10 false *c (*i) 5.531,2.833 5.781,3 0.25,0.167 10 false *e 3.76,2.833 4.01,3 0.25,0.167 10 false *f 2,2.833 2.25,3 0.25,0.167 10 false *g 0.229,2.833 0.479,3.083 0.25,0.25 10 false *h 0.125,1.719 0.438,1.875 0.313,0.156 10 false *d 6,1.083 6.333,1.333 0.333,0.25 10 false *k 3.458,1.333 3.792,1.583 0.333,0.25 10 false *j
*a Odometer *b Trip Meter A
*c Trip Meter B *d Meter Panel Luminance Adjustment Mode
*e Luminance Ratio 100 % *f Luminance Ratio 75 %
*g Luminance Ratio 50 % *h Luminance Ratio 25 %
*i Pressing ODO/TRIP switch for 0.8 seconds or more to reset. *j Taillight is off
*k Taillight is on - -
V100135

Pressing ODO/TRIP switch for less than 0.8 seconds.
V100136

Pressing ODO/TRIP switch for 1.0 seconds or more.
V100137

Pressing ODO/TRIP Switch for less than 0.8 seconds, ignition switch is off or ODO/TRIP switch is not operated for 10 seconds or more. - -


HINT:

The illustrations shown are examples only. The illustrations may differ the actual vehicle screen.




b.

Multi-information Display (Models with Optitron Type Combination Meter Assembly)

i.

The multi-information display has 3 areas depending on the display mode.

Y246587C01
5.625,1.094 5.458,0.802 true 5.667,1.625 5.438,1.885 true 1.583,2.24 1.823,1.823 true 2.885,1.823 3.188,2.26 true 6.427,1.125 6.583,0.802 true 1.5,2.271 1.813,2.427 0.313,0.156 10 false *1 3.135,2.281 3.448,2.438 0.313,0.156 10 false *2 4.719,0.656 5.031,0.813 0.313,0.156 10 false *3 5.313,0.688 5.625,0.844 0.313,0.156 10 false *4 5.302,1.833 5.615,1.99 0.313,0.156 10 false *5 6.594,0.688 6.906,0.844 0.313,0.156 10 false *6
*1 DISP Switch *2 ODO/TRIP Switch
*3 Multi-information Display *4 Drive Information Display
*5 ODO/TRIP Meter *6 Outside Temperature Display



ii.

Drive Information Display

·

The drive information display changes in the order shown below by pressing the DISP switch.

·

The average fuel consumption value can be reset by pressing and holding the DISP switch for 0.8 seconds or more.


Flow of Drive Information Display
Y246588C01
2.969,1.104 3.281,1.26 0.313,0.156 10 false *b 5.521,1.104 5.833,1.26 0.313,0.156 10 false *c 5.5,2.208 5.813,2.365 0.313,0.156 10 false *d 5.521,3.302 5.833,3.458 0.313,0.156 10 false *e 2.958,3.302 3.271,3.458 0.313,0.156 10 false *f 0.417,1.104 0.854,1.302 0.438,0.198 10 false *a (*i) 0.406,3.313 0.719,3.469 0.313,0.156 10 false *g 0.417,2.198 0.729,2.354 0.313,0.156 10 false *h
*a Average Fuel Consumption *b Average Vehicle Speed
*c Driving Time *d Cruising Range
*e DPF Sedimentation Bar Display *f Meter Panel Luminance Adjustment Display
*g Settings *h Warning Message
*i Pressing DISP switch for 0.8 seconds or more to reset. - -
V100135

Pressing DISP switch for less than 0.8 seconds. - -


HINT:

The illustrations shown are examples only. The illustrations may differ the actual vehicle screen.



iii.

Meter Panel Luminance Adjustment Display

·

While the meter panel luminance adjustment mode is displayed, the brightness of the meter can be changed by pressing DISP switch for 1 second or more. The brightness of the meter can be adjusted in 5 levels.


Flow of the Meter Panel Luminance Adjustment Display
Y246591C01
0.604,1.115 0.938,1.281 0.333,0.167 10 false *a 2.927,1.115 3.177,1.281 0.25,0.167 10 false *b 5.25,1.115 5.5,1.281 0.25,0.167 10 false *c 4.031,2.458 4.281,2.625 0.25,0.167 10 false *d 1.813,2.458 2.063,2.625 0.25,0.167 10 false *e
*a Luminance Ratio 100 % *b Luminance Ratio 75 % (Tail Light in OFF)
Luminance Ratio 25 % (Tail Light in ON)
*c Luminance Ratio 50 % (Tail Light in OFF)
Luminance Ratio 12.5 % (Tail Light in ON)
*d Luminance Ratio 25 % (Tail Light in OFF)
Luminance Ratio 6.25 % (Tail Light in ON)
*e Luminance Ratio 12.5 % (Tail Light in OFF)
Luminance Ratio 3 % (Tail Light in ON)
- -
V100135

Pressing DISP switch for 1.0 seconds or more. - -


HINT:

The illustrations shown are examples only. The illustrations may differ the actual vehicle screen.



iv.

Outside Temperature Display

·

The outside temperature display and ice warning light was provided on the multi-information display.

·

When the outside temperature drops below 3 °C, an ice warning light flashes 10 times to warn the driver to drive with caution due to icy road conditions. After the ice warning light flashes 10 times, the light stays on.

·

When the outside temperature reaches 5 °C, the light goes off.


Y246589C01
5.698,0.625 6.073,0.5 true 6.115,0.406 6.427,0.563 0.313,0.156 10 false *1 1.333,1.333 1.583,1.5 0.25,0.167 10 false *a 4,1.333 4.25,1.583 0.25,0.25 10 false *b
*1 Ice Warning Light - -
*a Outside Temperature Display *b When below 3 °C



v.

ODO/TRIP Meter

·

The ODO/TRIP meter display changes in the order shown below by pressing the ODO/TRIP switch.


Flow of the ODO/TRIP Meter
Y246590C01
0.75,1.083 1,1.25 0.25,0.167 10 false *a 2.917,1.083 3.417,1.25 0.5,0.167 10 false *b (*d) 5,1.083 5.417,1.25 0.417,0.167 10 false *c (*d)
*a Odometer *b Trip Meter A
*c Trip Meter B *d Pressing ODO/TRIP switch for 0.8 seconds or more to reset.
V100135

Pressing ODO/TRIP switch for less than 0.8 seconds. - -



vi.

Setting Function

·

The items displayed on the multi-information display can be customized.

·

The following items can be selected on the information setting screen.


Item Available Setting
Language The language used on the multi-information display can be selected:
·

English

·

Simplified Chinese

·

Traditional Chinese


Units The unit displayed on the multi-information display can be selected:
·

km (km/L)

·

km (L/100 km)




vii.

Warning Mode Function

·

When a warning is necessary, the warning message interrupts the current display on the multi-information display.

·

A warning message is displayed via an interrupt display when a vehicle malfunction occurs to warn the driver. Also, an advice message is displayed via an interrupt display depending on the situation, such as when the driver must proceed with caution.

·

The buzzer in the combination meter assembly may sound depending on the item displayed on the multi-information display.


Engine System
1.

The combination meter assembly displays the following messages based on signals received from the engine oil pressure switch assembly.

Message Master Warning Light Buzzer
ENGINE OIL
PRESSURE LOW
Illuminates Sounds

2.

The combination meter assembly displays the following messages based on signals received from the engine oil level sensor.

Message Master Warning Light Buzzer
ENGINE OIL LOW Illuminates Sounds

3.

The combination meter assembly displays the following messages based on signals received from the fuel sedimenter level warning switch.

Message Master Warning Light Buzzer
DRAIN WATER
FROM FUEL FILTER
Illuminates Sounds

4.

The combination meter assembly displays the following messages based on signals received from the fuel sedimenter level warning switch.

Message Master Warning Light Buzzer
REPLACE FUEL FILTER - -


UREA Selective Catalytic Reduction (SCR) System
1.

The combination meter assembly displays the following messages based on signals received from the emission control ECU assembly via the ECM.

Message Master Warning Light Buzzer
AdBlue LOW - -
REFILL AdBlue NOW Illuminates Sounds
REFILL AdBlue NOW
LOW POWER
Illuminates Sounds
INCORRECT AdBlue
DETECTED
Illuminates Sounds
INCORRECT AdBlue
DETECTED
CHANGE AdBlue NOW
Illuminates Sounds
INCORRECT AdBlue
DETECTED
UNABLE TO
RESTART ENGINE
CHANGE AdBlue NOW
Illuminates Sounds
INCORRECT AdBlue
DETECTED
LOW POWER
CHANGE AdBlue NOW
Illuminates Sounds
SCR MALFUNCTION Illuminates Sounds
SCR MALFUNCTION
CHECK AdBlue
VISIT YOUR DEALER
Illuminates Sounds


Brake System
1.

The combination meter assembly displays the following messages based on signals received from the parking brake switch assembly and skid control ECU.

Message Master Warning Light Buzzer
RELEASE
PARKING BRAKE
Blinks Sounds




c.

Rental Car Mode Display Function

i.

A rental car mode display function was provided to display the odometer and switch on the backlight for a fixed time when the ignition switch was switched from ON to OFF or when the driver's seat door was opened while the ignition was off.


ii.

The rental car mode display function displays the odometer and switches on the backlight when the ignition switch is switched from ON to OFF or when the driver's seat door is opened while the ignition is off.


iii.

The display of the multi-information display switches as shown below when the ignition switch is operated or when the driver's seat door is opened.

HINT:

The rental car mode display function is activated when the driver's seat door was opened on RHD models only.


Flow of the Rental Car Mode Display (Analog Type Combination Meter Assembly)
Y226488C01
0.25,0.25 0.5,0.417 0.25,0.167 10 false *a 4.958,0.25 5.208,0.417 0.25,0.167 10 false *b 0.438,0.646 0.688,0.813 0.25,0.167 10 false *c 2.875,0.646 3.292,0.813 0.417,0.167 10 false *d (*f) 5.313,0.646 5.729,0.813 0.417,0.167 10 false *e (*h) 1.198,1.583 1.448,1.833 0.25,0.25 10 false *g
*a While Ignition Switch is OFF *b While Ignition Switch is ON
*c Display Off *d Rental Car Mode Display
*e Normal Display *f Backlight is switched on at the same time.
*g RHD models only *h The item selected the last time the ignition was switched on is displayed.
V100135

Ignition switch is turned to ON
V100136

Ignition switch is turned OFF
V100137

Driver's seat door is open
V100138

After 30 seconds has passed from the start of display (rental car mode display timeout)


HINT:

The illustrations shown are examples only. The illustrations may differ the actual vehicle screen.


Flow of the Rental Car Mode Display (Optitron Type Combination Meter Assembly)
Y246592C01
0.333,0.333 0.583,0.5 0.25,0.167 10 false *a 4.833,0.333 5.083,0.5 0.25,0.167 10 false *b 0.583,0.573 0.833,0.74 0.25,0.167 10 false *c 2.917,0.573 3.333,0.74 0.417,0.167 10 false *d (*f) 5.25,0.573 5.667,0.74 0.417,0.167 10 false *e (*g)
*a While Ignition Switch is OFF *b While Ignition Switch is ON
*c Display Off *d Rental Car Mode Display
*e Normal Display *f Backlight is switched on at the same time.
*g The item selected the last time the ignition was switched on is displayed. - -
V100135

Ignition switch is turned to ON
V100136

Ignition switch is turned OFF
V100137

Driver's seat door is open
V100138

After 30 seconds has passed from the start of display (rental car mode display timeout)


HINT:

The illustrations shown are examples only. The illustrations may differ the actual vehicle screen.




d.

DPF Sedimentation Bar Display

i.

A DPF sedimentation bar display was employed to display the amount of Particulate Matter (PM) deposited in the DPF catalyst using a 10-stage bar graph.


ii.

An LCD for DPF sedimentation bar display was installed under the tachometer on the models with analog type combination meter assembly.

Displayed Information
Display Item Display Outline
DPF Sedimentation Bar Display Analog Type Combination Meter Assembly
Y246596

The amount of Particulate Matter (PM) deposited in the DPF catalyst is displayed using a 10-stage bar graph.
Optitron Type Combination Meter Assembly
Y246594




e.

Shift Position Indicator (Models with A861E A/T)

i.

A shift position indicator was employed to display the current shift position.


ii.

An LCD for shift position indicator was installed under the tachometer.

Y246593C01
1.094,2.708 1.406,2.865 0.313,0.156 10 false *a
*a Shift Position Indicator - -
V100135

Shift Lever Operation
V100136

First Hold Switch (No. 1 Pattern Select Switch Assembly) Operation




f.

Buzzer

i.

The table below shows the warning and reminder functions of the buzzer in the combination meter assembly.

Priority Item
1 Driver Seat Belt Warning (Models for G.C.C. Countries)
2 Emergency Door Warning
3 Driver Seat Belt Warning (Excluding Models for G.C.C. Countries)
4 Passenger Seat Belt Warning
5 Brake Fluid Low Warning
6 Vacuum Warning
7 Engine Oil Pressure Warning
8 Engine Coolant Temperature Warning
9 Multi-information Display Warning
10 Speed Warning
11 Parking Brake Unreleased Warning
12 Door Open while Driving Warning
13 Fuel Sedimenter Warning
14 DPF Warning

HINT:

The buzzer function differs by the vehicle specification.




g.

Back Buzzer Control Function

i.

A back buzzer control was provided to notify bystanders that the vehicle is reversing by sounding the back buzzer assembly when the shift position was set to "R". The meter ECU controls the back buzzer assembly.


ii.

If a shift position R signal is input from the back-up light switch assembly*1 or ECM*2, the meter ECU sounds the back buzzer assembly intermittently.

*1: Models with M/T

*2: Models with A/T


System Diagram
Y276434E01
3.333,1.333 4.083,1.667 0.75,0.333 10 false Meter ECU 5.417,1.5 6.917,1.833 1.5,0.333 10 false Back Buzzer Assembly 3.083,0.333 4.333,1 1.25,0.667 10 false Combination Meter Assembly 0.5,0.333 1.917,1 1.417,0.667 10 false Back-up Light Switch Assembly*1 0.917,1.479 1.5,1.771 0.583,0.292 10 false ECM*2 0.167,2.417 1.5,2.75 1.333,0.333 10 false *2: Models with A/T 0.167,2.083 1.5,2.417 1.333,0.333 10 false *1: Models with M/T



h.

Seat Belt Warning Function (Models with Seat Belt Warning System)

i.

Seat Belt Warning Function (Models for G.C.C. Countries)

·

When the ignition switch is ON, this system detects the condition of the seat belt based on the signal from the driver seat belt buckle switch.

·

If the ignition switch is turned to the "ON" position with the seatbelt unbuckled, the buzzer sounds for the 8 seconds.

·

If the vehicle reaches a speed of 20 km/h (12.4 mph) with the seatbelt unbuckled, the buzzer sounds once. If the seat belt is still unbuckled after 24 seconds, the buzzer will sound intermittently for 6 seconds. Then, if the seat belt is still unbuckled, the buzzer will sound in a different tone for 90 seconds.

·

Once a buzzer begins to sounds, it will continue until the driver seat belt is buckled or the ignition switch is turned off.



ii.

Seat Belt Warning Function (Excluding Models for G.C.C. countries)

·

When the ignition switch is ON, this system detects the condition of the seat belt based on the signal from the driver seat belt buckle switch or passenger seat belt buckle switch*.

·

If the vehicle reaches a speed of 20 km/h (12.4 mph) with the seatbelt unbuckled, the buzzer will sound intermittently for 24 seconds. Then, if the seat belt is still unbuckled, the buzzer will sound in a different tone for 100 more seconds.

·

Once a buzzer begins to sounds, it will continue until the driver seat belt or passenger seat belt* is buckled or the ignition switch is turned off.

*: Models with passenger seat belt warning system